Xerox 8254E User Manual

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide4-67 d. Press the [Enter] key. "PF2: Initial Change" displays in the control panel.
• The initial adjustment value is saved.
5. Perform Confirm Print.
a. Press the [+] key or [–] key to select "PF3: Confirm Print.".
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide 4-68b. Press the [Enter] key. "Feed Length: 250 mm" displays in the control panel.
Notes:
•The length of media that is fed (i.e., the feed length) for confirmation adjustment 
printing is normally set at 250mm.
•If you increase the feeding length, the accuracy of the Media feed compensation 
improves.
•To change the feeding length, press the [+] key or [–] key and change the set value.
c. Press the [Enter] key. "Printing" displays in the control panel.
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide4-69
• Confirmation adjustment printing starts.
• When the Confirm Print operation is complete "Ready to Print" displays in the control panel.
• After the confirmation adjustment printing is complete, cut the media.
Cutting Media
6. Measure the distance between the two plus marks (+) in the confirmation adjustment print, using a 
ruler. Then, confirm that the measured distance matches the feed length when printing.
a. If the measured distance does not match the feed length, follow the procedure from Steps 1 through 5 
and re-adjust.
b. If the measured distance does
 match the feed length, proceed to Step 7.
7. If you see banding or waves in the print, perform Micro adjustment printing.
a. Display the Media feed compensation menu in the control panel in the same way as in Step 1.
b. Press the [+] key or [–] key to select "PF4:Micro Print."
No.Name
1Feed length
2Media feeding direction
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide 4-70c. Press the [Enter] key. "Printing" displays in the control panel.
• Micro adjustment printing starts.
Notes:
•If, after viewing the first band, you feel that the adjustment might not have been large 
enough, you do not have to wait for all five bands of the image to finish printing. You can 
speed things up by doing the following:
–Press the [Cancel] key.
–Make another adjustment.
–Run again.
•When you feel you are in the correct region, run again and view all five bands to confirm 
that the adjustment is correct.
d. Press the [Enter] key.
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide4-71
8. If you see white or dark lines on all bands, you may have to adjust the pulse to a greater +/- value 
than +/- 2 and retry.
• After the micro adjustment printing is completed, "PF4:Micro Print" displays in the control 
panel.
9. Refer to the illustrations below and check the printing result.
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide 4-72
10. Set up Micro Adjustment Change.
a. Press the [+] key or [–] key to select "PF5:Micro Change."
b. Press the [Enter] key. "Micro: 0pulse" displays in the control panel.
c. Press the [+] key or [–] key and enter the micro adjustment value according to the printing result in Step 
7.
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide4-73 d. Press the [Enter] key.
•The micro adjustment value is saved.
•"PF5:Micro Change" displays in the control panel.
11. Press the [Cancel] key several times. "Ready to Print" displays in the control panel.
The adjustment of the Media feed compensation value is complete.
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide 4-74
8264E only - Installing Media Holder Plates
Variations in quality and use conditions can cause the edges of the media to curl, resulting in damage 
to the media by the print head surface. To prevent this, use the media holder plates to reduce the 
amount of curling in the media.
Follow the procedure below to install the media holder plates.
1. Display the Side margin menu in the control panel.
a. Press the [Menu] key. "Menu 1: Setup>" displays in the control panel.
b. Press the [>] key. "Set1: MediaType" displays in the control panel.
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide4-75 c. Press the [+] key or [–] key to select "Set4: Side Margin."
d. Press the [Enter] key. "Side Margin: ** mm" displays in the control panel.
Side Margin Menu
Note:
•The current setting value is displayed in the "**" of the Side Margin menu.
2. Set up the margins (side margins) to 10mm while printing.
a. Press the [+] key or [–] key to select "Side Margin: 10 mm."
Downloaded From ManualsPrinter.com Manuals 
						

							Handling the Printer
Xerox 8254E / 8264E Color Wide Format Printer
User Guide 4-76b. Press the [Enter] key. This saves the setting and "Set4: Side Margin" is again displayed in the control 
panel.
c. Press the [Cancel] key several times. "Ready to Print" displays in the control panel.
3. Load the roll media.
Setting Roll Media
4. Set the media holder plates by sliding them from both sides of the platen.
Note:
•Do not use the media holder plates for media whose thickness is 400μm (0.4mm) or 
greater. The media holder plate may interfere with the print head. 
Downloaded From ManualsPrinter.com Manuals