Vodavi Starplus Triad S Description Manual
Here you can view all the pages of manual Vodavi Starplus Triad S Description Manual. The Vodavi manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 411
Customer Database Programming Introduction FeaturesVoicemail In-Band Signaling Voicemail Disconnect Table VOICE MAIL IN-BAND FEATURES Voicemail In-Band Digits Voicemail Transfer/Forward Voicemail Broker VOICE MAIL INDEX TABLE Voicemail Group Voicemail ID NumberFLASH 67 FLASH 68 FLASH 70 EXCEPTION TABLES PROGRAMMING TOLL RESTRICTION PROGRAMMING Allow Table A Programming Deny Table A Programming Allow Table B Programming Deny Table B Programming Special Table 1 Programming Special Table 2 Programming...
Page 412
I-16Customer Database Programming Introduction FeaturesProgram CodeFlex ButtonDefault ValueSpecial Table 4 Programming 8Home Area Code for Special Table 1 9Area Code for Special Table 2 10Area Code for Special Table 3 11Displaying Toll Table Entries 12LEAST COST ROUTING (LCR) PROGRAMMING LCR TABLES PROGRAMMINGFLASH 75 3-Digit Area/Office Code Table 1See LCR Tables 6-Digit Area/Office Code Table 2None Exception Code Table 3See LCR Tables Route List Table 4 Insert/Delete Table 5Daily Start Time Table...
Page 413
Customer Database Programming Introduction FeaturesInitialize ICLID-DID Tables Initialize Directory Dialing Tbl Parameters Initialize Hunt Group Parameters Initialize ACD*/UCD Group Parameters Initialize Voicemail* Group Parameters Initialize Verified Account Code Table System Reset PRINTING SYSTEM DATABASE PARAMETERS INTRODUCTION Printing System Parameters Printing CO Line Attributes Printing Station Attributes Printing CO/Station Port Parameters Printing Exception Tables Printing System Speed Numbers...
Page 414
~...l-18 Customer Database Programming Introduction FeaturesProgram CodeFlex ButtonDefault ValueLOAD DATABASE ROUTINE FLASH 86 {:;I::;, 2,lLi5. _i_. .._ ._-.z.- -.-.._Upload database 1PC Only Download database 2PC OnlyL* Features available with Optional Software Table 2-l: Default Values Issue I- December 1998STARPLUS Triad-S System Programming Manual
Page 415
Customer Database Programmingl-19 Program Mode Entry (Key Station) Program Mode Entry (Key Station) Programming is performed at Station 100 (defaults to Port 01) using a 24-button Digital Display Terminal. Programming is always done at this station regardless of the class of service or which station has been assigned the attendant(s). Before entering the program mode, the programmer must verify that Station 100 is properly connected. To enter the program mode: 1Press the ON/OFF button (optional). LED...
Page 416
I-20Customer Database Programming Customer Data Worksheets Use the procedures below to return the system database to default values: 1Place Switch #l on the BKSU in the ON position. 2Turn the power off and on to initialize the system database to the default. 3Once the database is initialized, place Switch #I in the OFF position to protect the database. Customer Data Worksheets Before attempting programming, it is strongly recommended that customer data worksheets be prepared (Refer to Product Desription...
Page 417
Customer Database Programming Database Upload/Download Routine Upload/Download through Remote Administration 1Connect one end of an RS232C serial cable from the RS-232C connector on the MISUof the Triad-S System to the desired Comm Port on the PC. Use a sfraighf-through LB-9 to DB-9 (female to female) cable. 2Load a communication software package (i.e., Procomm) into the PC. Make the necessary changes to the following areas of the communications package. Save these permanent settings. Items to Change...
Page 418
l-22Customer Database Programming Database Upload/Download Routine 2-I: Data Terminal Program Codes Cross Reference for terminal characters that representthe key set buttons. By entering [?] from the terminal, a Help screen displays. 5Enter the information on the following screen capture. Continue with the steps that follow. 44 Digital Hybrid Key-SystemEng. Ver. 1.36-FFFF DATE:12/01/98 TIME:15:37:14 ENTER PASSWORD: admr ADMIN PROGRAMMING adm>, ENTER PROGRAM NO adm>86 LOAD DATABASE ROUTINE ENTER BUTTON...
Page 419
Customer Database Programming Database Upload/Download Routinel-23 7This displays the Receive XMODEM screen on the PC monitor. Enter a path and file name for the database file and press to begin the download routine. Receive XMODEM Please enter filename: 8On the PC, press to begin the download routine. A Confirmation tone is heard from the communications package after the download is complete and theADM> prompt displays. 9Enter M and press . 10On the PC, press + . Press to exit Procomm and return to...
Page 420
. .l-24Customer Database Programming Database Upload/Download Routine IEnter the information on the following screen capture. 44 Digital Hybrid Key-SystemEng. Ver. 1.36-FFFF DATE:12/01/98 TIME:15:37:14 ENTER PASSWORD: adm> ADMIN PROGRAMMING adm>, ENTER PROGRAM NO adm>86 LOAD DATABASE ROUTINE ENTER BUTTON NUMBERThe HOLD button on adm>wa key set is the DOWNLOAD DATEBASEsame as the PRESS HOLD +- kS;szn,;;;e;;yboard. adm> 2On the PC, press to display the Upload Protocol screen. Enter X to set the upload...