Vodavi Starplus Sts Key Systems Programming Operation Manual

ICLID ProgrammingA-7
ICLID / Caller ID
2. To program ICLID features, use the flexible button(s) as defined in the following 
procedures.
Button # 1 = Disable/Enable
Button # 2 = Name In Display
Button # 3 = Baud Rate Display
Button # 4 = Port Assignment
3. After all entries are made, press HOLD to accept the data.
When entering the ICLID features programming area the buttons on the digital telephone are 
defined as shown below:
Enable/Disable
Description
The ICLID (Incoming Calling Line IDentification)...

A-8ICLID Programming
ICLID / Caller ID
Baud Rate Display
Description
The STS system can provide ICLID input on the standard RS-232C of the BKSU (also on
LCOB w/CIDU. The baud rate is displayed as 150, 300, 600, 1200, 2400, 4800, 9600, or 19.2K 
baud.
Programming Steps
The ICLID baud rate is programmed using FLASH 15 Baud Rate assignments. The LCD 
displays the current baud rate based on which number is assigned to the ICLID Port number.
DEFAULT … Baud Rate is 9600.
Port Assignment
Programming Steps
1....

ICLID ProgrammingA-9
ICLID / Caller ID
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press Button #21 to select Page C. The display updates. The following message displays to 
indicate current programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the RING DELAY TIMER flexible button (FLASH 40, Page C, Button...

A-10ICLID Programming
ICLID / Caller ID
Initialize ICLID-DID Tables
Description
ICLID - DID  Table parameters may be initialized, setting all data fields to their original default 
values.
Programming Steps
1. Press the ICLID TABLES flexible button (FLASH 80, Button #8). The following message 
displays:
2. Press the HOLD button. A confirmation tone sounds.
Ta b l e  A - 1 :  IC L I D  Ta b l e  D e f a u l t s
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
FLASH 43 ICLID TABLES...

ICLID ProgrammingA-11
ICLID / Caller ID
Print ICLID - DID Tables
Description
The Print ICLID-DID Tables command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device. When printing the ICLID - DID Tables, the following data prints (an 
example follows the programming steps):

ICLID Features

ICLID Translation Table

ICLID Unanswered Call Table

ICLID Ringing Assignments Table

DID...

A-12ICLID Programming
ICLID / Caller ID
Figure A-2: ICLID - DID Tables Printout
ICLID NAME BAUD PORT
N Y 9600 1
ICLID TRANSLATION TABLE
-----------------------
ENTRY ROUTE NAME NUMBER
600 ## .
601 ## .
602 ## .
603 ## .
... and so on through 799 .
ICLID UNANSWERED CALL TABLE
---------------------------
NONE
ROUTE RING ASSIGNMENTS
----------------------
00
NONE
01
NONE
... and so on through 99 - NONE
100
S100A
101
S101A
... and so on through 149 - S149A
150
NONE
151
NONE
... and so on through 251 - NONE...

ICLID Call Management Tables A-13
ICLID / Caller ID
ICLID Call Management Tables
Description
Two ICLID Call Management Tables are maintained in the system. These tables consist of an 
Answered Call Management Table and an Unanswered Call Management Table. Each have a 
100-entry capacity.
Answered Call Management Table
Description
The Answered ICLID Table feature adds a table that captures the ICLID calls that were 
answered. The table can store up to 100 entries of the most recently answered ICLID calls....

A-14 ICLID Call Management Tables
ICLID / Caller ID
Unanswered Call Management Table
Description
An Unanswered Call Management Table with 100 entry capacity is maintained in the system. 
The calling number/name information pertaining to any unanswered call is placed in this 
table at the time the system determines the call was abandoned.
This table may be accessed from any display telephone to review unanswered calls. Only an 
Attendant station can delete an entry from this table.
Operation
To enter the...

B
Least Cost Routing
This section describes the Least Cost Routing (LCR) feature and how to program the
eight LCR Tables to monitor the digits dialed at each station and select the best route
for the call.