Vodavi Starplus Sts Key Systems Programming Operation Manual

School Zone2-231
Features and Operation
Operation
To control School Zone call forwarding (at an Administrator station):
1. Dial [630] + a call forward condition code (0 or 6-9) + a valid destination number
Call Forward Condition Codes: Valid Destinations:
0 = Disabled Station Numbers
6 = All Call Forward Hunt Groups
7 = No Answer Call Forward UCD Groups
8 = Busy Call Forward Voice Mail Groups
9 = Busy / No Answer Call Fwd
2. Press [HOLD]. A confirmation tone sounds.
To view the call forwarding status of...

2-232Single Line Telephone
Features and Operation
Single Line Telephone
Compatibility
Description
The STS supports industry standard 2500-type (DTMF) single line telephone (SLT) 
instruments. When the Circuit Single Line Interface Board (CSIB) is installed in the STS, a 
maximum of 24 single telephones can be supported.
SLT DTMF Receiver Timer
Description
Single line telephones require the use of a DTMF receiver when going off-hook and dialing. 
When SMDR or toll restriction (via COS assignments) is...

Single Line Telephone2-233
Features and Operation
Programming Steps
1. Press the SLT HOOK FLASH TIMER flexible button (FLASH 01, Button #14). The following 
message displays:
2. Enter a valid number on the dial pad that corresponds to 0.5-2.0 seconds in 1/10 second 
increments.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … SLT Hook Flash Timer is set at 10 (one second).
SLT Hook Flash Bounce Timer
Description
The SLT Hook Flash Bounce Timer determines the...

2-234Software Version (MBU)
Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … SLT Hook Flash Bounce Timer is set to 0.30 seconds.
Software Version (MBU)
Description
The current system software version of the Main Board Unit (MBU) can be viewed. The display 
shows the version number and level of software.
Operation
To view the Software Version Display:
Dial the S/W Display code [605] on the dial pad. The top line of the LCD shows the...

Speakerphone2-235
Features and Operation
2. Enter the range of fixed station numbers (100-149) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current programming...

2-236Sp ee d Di al
Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Speakerphone Operation
Description
The Speakerphone feature allows you to conduct a conversation without lifting the handset. 
Speakerphone volume can be adjusted as desired.
Operation
1. Press ON/OFF button to...

Speed Dial2-237
Features and Operation
Operation
To use speed dial:
1. If an outside line was not specified in programming, one can be selected now or the 
system assigns the line.
2. Press the SPEED button and dial speed bin location,
-or-
Press the preprogrammed speed bin button,
-or-
Use the Soft Key’s SPD option and dial a speed bin location when in an idle condition.
To store speed dial numbers:
1. Press the SPEED button once.
2. Press an OUTSIDE LINE button or POOL button.
-or-
Select an outside...

2-238Sp ee d Di al
Features and Operation

SINGLE LINE TELEPHONE
To use speed dial:
1. Lift handset.
2. Dial [668] on the dial pad.
3. Dial desired station or system speed bin number (9000-9099).
4. Replace the handset to end the call.
To store speed dial numbers:
1. Lift handset.
2. Dial [661] on the dial pad.
3. Dial desired station speed number (9000-9019).
4. Dial telephone number to store.
5. Briefly press and release the hookswitch. A confirmation tone sounds.
System Speed Dial Access
Description...

Speed Dial2-239
Features and Operation
2. Enter the range of fixed station numbers (100-149) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the SPEED flexible button (Button #6). The following message...

2-240Sp ee d Di al
Features and Operation
Speed Bins - Chaining
Description
Speed dial bins can be chained together. This is helpful for accessing Long Distance carriers 
or banking services when account codes are required.
Operation
 To chain speed bins together, simply press one speed bin and then another as required.
Initialize System/Station Speed Numbers
Description
System and Station Speed bins may be initialized to reset all bins to their original default 
value (empty). All bins 9000-9099 are...