Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

SYSTEM PARAMETERS PROGRAMMINGSTARPLUS @ SPD 4696
Digital Key Telephone SystemMISC. SYSTEM PARAMETERS
610.4FLASH RATES (Programmable)
Programming Steps
If the system is in the programming mode, continue
using the program codes, If starting to program here,enter the programming mode. Refer to Sec. 600.2,
Program Mode Entry (Key Station)
If Flash Rate(s) are to be changed:
a. Press FLASH and dial 
[07]. The following mes-
sage is shown on the display phone:
A.incoming CO Line Ringing
Programming Steps
If...

STARPLUS @ SPD 4696
Digital Key Telephone SystemSYSTEM PARAMETERS PROGRAMMING
FLASH RATES (Cont’d)
6. Incoming Intercom RingingProgramming Steps
a. Press the INCOMING INTERCOM RINGING
flexible button (Button 
#2). The following mes-
sage is shown on the display phone:
;iDescription
The Incoming Intercom Ringing flash rate can be
programmed to 16 different options identified in the
flash rate table. This allows the user to customize thekey system configuration to desired flash rates.
Default: By default,...

SYSTEM PARAMETERS PROGRAMMINGSTARPLUS @ SPD 4696
Digital Key Telephone SystemMISC. SYSTEM PARAMETERS
610.5
ATI-ENDANT STATION ASSIGNMENT
Programming Steps
If Attendant Station(s) are to be changed:
a. Press FLASH and dial 
[lo]. The following mes-
sage is shown on the display phone:
b. Enter up to three three-digit station number(s)
on the dial pad.
c. Press the HOLD button to save the entry. Con-
firmation tone is heard and the display will now
update.610.6
SYSTEPul TIME AND DATE
Programming Steps
To...

STARPLUS @ SPD 4896
Digital Key Telephone System
MISC. SYSTEM PARAMETERS (Cont’d)
610.7
PBX DIALING CODES
Programming Steps
Description
If PBX Diaiing Codes are to be assigned:
a. Press FLASH and dial 
[12]. The following mes-
sage is shown on the display phone:Five one or two-digit PBX access codes can be
programmed into memory. When dialed, these
codes signal the system so that toll restriction is
applied at the next dialed digit. When a single digit
code 
[9] is entered, it must be followed by the...

SYSTEM PARAMETERS PROGRAMMINGSTARPLUS @ SPD 4696
Digital Key Telephone SystemMISC. SYSTEM PARAMETERS (Cont’d)
610.9
RELAY/SENSOR PROGRAMMING
Programming Steps
it is necessary to assign a Station ID to the
station. port usad for a Relay&ensof InterfaceModuk Refer ta Sec. 63U.2, item A. Stationidenttfkatfon before proceeding.!
If Relays are to be assigned:a. Press FLASH and dial 
[14]. Relay #l (Flex
Button 
#l) and Relay/Sensor #l (Flex Button
#12) LEDs will be lit indicating the system is in
the...

STARPLUS @ SPD 48%
Digital Key Telephone SystemSYSTEM PARAMElERS PROGRAMMING
RELAY/SENSOR PROGRAMMING (Cont’d)
A.Programming relay for External Paging:Programming Steps
1.Press the appropriate flex button 12 thru 15 toindicate which Relay/Sensor interface Mod-
ule is to be programmed.
2.Press flex buttons (I-3) to indicate the desired
relay to be programmed.
3.Dial [l] on the dial pad.
4.Enter a one-digit page zone number (l-7)
5. Press the HOLD button to save the entry.
Confirmation tone is heard and...

SYSTEM PARAMETERS PROGRAMMING
STARPLUS @ SPD 4896
Digital Key Telephone System
RELAY/SENSOR PROGRAMMING (Cont’d)
C.Programming relay for Power Failure
Transfer:Programming Steps
I.Press the appropriate flex button 12 thru 15 to
indicate which Relay/Sensor interface Mod-
ule is to be programmed.
2. Press flex buttons (l-3) to indicate desired
relay to be programmed.
3.Dial [3] on the dial pad.
4. Press the HOLD button to save the entry.
Confirmation tone is heard and the display will
now...

STARPLUS @ SPD 4896
Digital Key Telephone SystemSYSTEM PARAMETERS PROGRAMMING
RELAY/SENSOR PROGRAMMING (Cont’d)
D.Programming relay for Loud Bell Control:Programming Steps
1.Press the appropriate flex button 12 thru 15 toindicate which Relay/Sensor Interface Mod-
ule is to be programmed.
2. Press flex buttons (l-3) to indicate desired
relay to be programmed.
3.Dial [4] on the dial pad.
4.Enter the three-digit station number (100-l 95)
5. Press the HOLD button to save the entry.
Confirmation tone is heard...

SYSTEM PARAMEFERS PROGRAMMING
RELAY/SENSOR PROGRAMMING (Cont’d)
E.Programming relay for CO Line Control:
STARPLUS @ SPD 4896
Digital Key Telephone System
1.
2.
3.
4.
5.Programming StepsDescription
Press the appropriate flex button 12 thru 
15 to
indicate which Relay/Sensor Interface Mod-
ule is to be programmed.
Press flex buttons (l-3) to indicate desired
relay to be programmed.
Dial 
[5] on the dial pad.
Enter a two-digit CO Line number (O-i-48)
Press the HOLD button to save the entry.
Confirmation...

STARPLUS @ SPD 4696
Digital Key Telephone System
SYSTEM PARAMETERS PROGRAMMINGI
RELAY/SENSOR PROGRAMMING (Cont’d)
G.Program sensing circuit as a RAN
Sensing (RAN END) circuit:
1.
2.
3.
4.
5.Programming Steps
Press the appropriate flex button 12 thru 15 toindicate which Relay/Sensor interface Mod-
ule is to be programmed.
Press flex buttons (4-6) to select the sensing
circuit to be programmed.
Dial 
[S] on the dial pad.
Enter a one-digit RAN Table number (I-8) the
sensing circuit should be associated to....