Vodavi Starplus Hybrid Key Telephone System Installation Manual

Starplus ’ 1428 In-Band Integration 
I 
J Connecting Blocks 
I 
12x4 I 
Ring 
SLl- 
r I I n-*-1 _- 
Generator - m 
pq 
I 
1428 HARDWARE REQUIREMENTS 
0 One 2 x 4 SLT expander card, each card provides 4 SLT circuits. Or one OPX box per VM port can 
be used. Each OPX box decreases EKT ports by one. 
0 One RM (DTMF receiver module) installed on the 2 x 4 SLT card. This will provide two (2) DTMF 
receivers total on the system. If the system has an expansion KSU and 2 x4 or 4 x 8 card installed, 
an...

CONFIGURING THE 1428 WITH THE Starplus AVP 
1. On the single line telephone ports that are to be assigned to the VM group disable the conference 
feature. Flash 50 XXX-XXX, button 3, LED should be OFF. Where XXX-XXX are the SLT extension 
range numbers to be assigned to the VM group. If you are using the supervised transfer feature, 
leave conference enabled on these ports. 
2. Enter the VM group programming for VM group 1 (440). Flash 65, button 1. This button should be lit 
for Steps 3-4. 
3. Enter the...

CONFIGURING THE Starplus AVP Cont’d 
9. From the Phone.Sys list select 1428.PBX and press the [ENTER] key. L 
10. Press the [ESC] key until the highlight bar is on the CONFIGURATION menu item. 
The ten step procedure above has loaded the following configuration parameters: 
n Dialing Prefixes 
Local Call = 
Long Distance = 9, (, = Pause) 
9,1 
8 Feature Prefixes 
Transfer Start = 
Set Message Wait = 
Clear Message Wait = 
Abort a Busy/No-Answer 
Reject a Caller = 
Transfer Connect = &,8# (& = hookflash)...

CONFIGURING THE Starplus AVP Cont’d 
EVENT HANDLER 
This item is in the COS menu and is used to match certain COS with specific call out lines. For 
example, mailboxes 100-l 27 could have a COS with event handler 1. Their message light and _ 
notification functions would be performed on the call out lines marked with a 1. To program this 
function: 
1. 
2. Highlight the MODULES menu item and press the [DOWN ARROW] key to pulldown 
the menu, 
Highlight the GLOBAL SETTINGS menu item and press the [ENTER]...

For a detailed description of each function please refer to the Starplus AVP manual, The appropriate 
sections are: 
Voice Messaging Page 620-l 2 
Auto Attendant Page 620-34 
Menu Routing Page 620-56  

Starplus @ 2856 In-Band Integration 
2856 HARDWARE REQUIREMENTS 
/ u ml’ 
Connecting 
Blocks 
L I 
Ring 4x8 * Telephone 
SLT - 
Interface 
, Generator - oud 
- Board 
pj - 
4x8 
cl -40 V dc _ 
Power Z 
jUPPlY 4= 
EKT 
Stations 
0 One 4 x 8 SLT expander card, each card provides 8 SLT circuits. Or one OPX box per VM port can 
be used. Each OPX box decreases EKT ports by one. 
0 One RM (DTMF receiver module) installed on the 4 x 8 SLT card. This will provide one (1) DTMF 
receiver per 4 X 8 board. This can...

CONFIGURING THE 2856 WITH THE Starplus AVP 
1. On the single line telephone ports that are to be assigned to the VM group disable the conference 
feature. Flash 50 XXX-XXX, button 3, LED should be OFF. Where XXX-XXX are the SLTLextension 
range numbers to be assigned to the VM group. If you are using the supervised transfer feature, 
leave conference enabled on these ports. 
2. Enter the VM group programming for VM group 1 (440). Flash 65, button 1. This button should be lit 
for Steps 3-4. 
3. 
4. Enter...

CONFIGURING THE Starplus AVP Cont’d 
The ten step procedure above has loaded the following configuration parameters: 
n Dialing Prefixes 
Local Call = 
9. (8 = Pause) 
Long Distance = 
9.1 
n Feature Prefixes 
Transfer Start = 
Set Message Wait = 
Clear Message Wait = 
Abort a Busy/No-Answer 
Reject a Caller = 
* Transfer Connect &,6# (& = hookflash) 
420@ (@ = extension number) 
421@ (@ = extension number) 
(L, 
& 
& 
8 
Mailboxes 100-l 55 and a disconnect mailbox of 999 
n Extensions 100-l 55 
l This...

CONFIGURING THE Starplus AVP 
Cont’d 
EVENT HANDLER 
This item is in the COS menu and is used to match certain COS with specific call out lines. For 
example, mailboxes 100-l 55 could have a COS with event handier 1. Their message light and 
notification functions would be performed on the call out lines marked with a 1. To program this 
function: 
1. 
2. Highlight the MODULES menu item and press the [DOWN ARROW] key to pulldown 
the menu. 
Highlight the GLOBAL SETTINGS menu item and press the [ENTER]...

For a detailed descriptiqn of each function please refer to the Starpius AVP manual. The appropriate 
sections are: 
Voice Messaging Page 620-l 2 
Auto Attendant Page 620-34 
Menu Routing Page 620-56