Vodavi Starplus Hybrid Key Telephone System Installation Manual

1) Speaker volume adjusts all voice signals sent to the speaker (i.e.. 
Speakerphone Conversations, Background Music, Page announcements) 
2) Ring Volume adjusts all tone signals sent to the speaker. 
i) Muted ringing will be proportionately quieter than normal ringing based on 
the volume setting. 
G. H-T-P Switch - Three position slide switch which controls the method of receiving 
intercom calls. 
a. Hand&e (I-I) Position - Upon hearing a tone burst and voice announcement over 
the speaker the User...

3) On/Off button (fixed)) 
4) Mute button (fixed) 
5) Speed button (fixed) 
6) Flash (fixed) 
7) Transfer button (fixed) 
8) Hold button (fixed) 
C. Speakerphone Description 
a. Hand&x intercom two-way conversation. 
b. Terminate call with the On/Off button. 
c. Automatic Pre-selection allows the speakerphone to be enabled by pressing a 
button (i.e.. DSS, CO Line, Page . . . . . etc..) 
D. Volume controls. 
E. H-T-P Switch - Three position slide switch which controls the method of receiving 
intercom...

: The following features are not allowed to be programmed onto DSSIDLS 
Console flexible buttons: ACD Agent or Supervisor Login, Do Not Disturb, Call 
Forward, Camp-on, Available/Unavailable, Personal Park, Voice Mail, and 
Headset Mode. The features may still be programmed onto the keyset fl 
Consoles may be associated with a station. No Duplicate 
Maps 1 and 2 permitted, more than one Map 3 may be associated with a station. 
6. SLT Adapter / Off-Premise Extension Module 
A. Uses a Digital Terminal Port...

9, PFTU - Power Fail Transfer Unit 
A. Provides the relay transfer circuits for up to 12 CO Lines in the event of a Power 
Failure. 
B. Controlled by a Relay Sensor Module Programmed for Power Fail Transfer. 
C. A customer provided 12 Volt DC Power Supply is required to operate the unit. 
Page 14  

System Check-Out 
I. Installation Check-Out List 
1. Power REQUIREMENTS. 
A. The System requires a Dedicated Branch Circuit. 
a. A good definition of the circuit is the use of a constant, separately fused, dedicated 
only to providing power to the KSUs power supplies, 117 volt plus or minus 5%, 
15 Ampere, Single Phase, 3-wire (parallel blade with ground) power outlet located 
within 5 feet of the KSU. KEEP THE POWER DEDICATED TO THE 
SYSTEM. 
2. Preliminary Procedures 
A. Test System Ground 
a. Ground...

E. After the LEDs return to their pattern, enter the programming mode either from 
Station 100 or via the RS232 communications port on the CPU and INITIALIZE the 
DATABASE (Flash 80, button 8, Hold). 
F. The System is now ready for programming. 
Page 16  

Customer Database Programming 
I. Introduction 
1. Flexible Programming allows the system to be tailored to the customers needs. 
2. No interruptions in call processing while programming the database. 
A. Exception is flexible port assignment. Requires a reset so system can assign time slots. 
3. Methods of Programming. 
A. From Station 100 (port 01) using a Executive Display Terminal. 
a. Enter the programming mode by dialing **3226. 
b. The On/Off Key on the terminal is lit. 
c. The System is ready to...

ii) While in programming entering a question mark (?) will return the Remote 
Administration Key Definitions. 
4. Data Base Programming Structure and Indications 
A. Once the database is entered programming of attributes is facilitated using Data Field 
(FLASH or Program Codes) codes. 
a. Data Fields are used as a method of Dividing the Database into Sections of Related 
Attributes, much like drawers within a file cabinet. Related items are grouped 
together and then an individual item is changed by...

B. Do a Flash 80, Press Flexible Button Eight (8), and Press Hold. System will initialize 
and reset. 
C. Customer Data Worksheets 
a. Prepare the worksheets prior to attempting programming. 
b. Save the sheets and update each time programming changes are made. 
c. Useful when programming because it contains most of the information necessary 
to program the entire system (Program Code, Button Map, Function, Format of 
Entry, Default Value). Very little supplemental information necessary to move 
around...

E. Download Instructions 
a. 
b. 
C. 
d. 
e. 
E 
8. 
h. 
i. 
i Connect an RS232-C Serial Cable from the compurter to an I/O port on the - 
System. 
Load the Procomm Plus software on the computer. Update the parameters in 
Procomm Plus to the settings given above. 
Press the EN7ER key on the computer. A prompt will display, requesting the 
system password be entered. Type the word VODA Ki’ and press IW7IX 
On the keyboard press CGA444 86 W. 
On the keyboard press ALT and then FI key simultaneously. This...