Vodavi Starplus 2448ex Hybrid Key Telephone System Installation Manual

sTARPLUS@ 2448EX Hybrid Key Telephone System 
VOICE MAIL GROUPS (Cont’d) 
c. ‘Leave” Mail Index Entry 
Programming Steps 
To specify the “Leave” mail index (outpulsing table) 
to be accessed by a Voice Mail group: 
1. Press the L flexible button (Button #I 0). 
2 Enter the one-digit outpulsing table number 
(O-7) on the dial pad. 
3. Press the HOLD button to enter the data. Description 
L The leave” mail index specifies the outpulsing 
Table where the “in-band” digits required to connect 
a caller,...

vy-H#i%melephone System sTARPLUS@ 2446EX 
610.37 VOICE MAIL OUTPULSING TABLE 
A. Voice Mail In-Band Signaling: 
Programming Steps 
If Voice Mail In-Band signalling is to be used: 
1. Press FLASH and dial [371. The following mes- 
sage is shown on the display phone. 
2. 
3. 
4. 
5. Where: 
y = the table index (O-7) 
x = entered digits (O-9, #, 
l , Pauses) 
Dial [O]-[7l for the y value (the table number 
entry of the voice mail entry you want to pro- 
gram). 
Dial one of the following, if required: 
0 =...

_ - 
sTARPLUS@ 2448EX Hybrid Key Telephone System 
. . 
VOICE MAIL OUTPULSING TABLE (Cont’d) 
B. Voice Mail Disconnect Table: 
Programming Steps Description 
1. 
2. 
3. 
4. Dial (81 for Table 8 (the table number used for 
the Voice Mail disconnect signal). 
Dial [0] for prefix. (required) 
Enter up to 12 digits which will be used for the 
disconnect signal, including ‘*’ and ‘W. TFtAN 
button = pause. 
Press the HOLD button. Display will now up- 
date. 
.-, 
To avoid Voice Mail ports from being tied up...

-5Y 
--  
/ 
SECTION 620 
1 
CO LINE ATTRIBUTES PROGRAMMING ’ 
620.1 CO LINE PROGRAMMING 
Programming Steps Description 
If the system is in the programming mode, continue 
using program codes. If starting to program here, 
enter the programming mode. If the system is in the 
programming mode, continue using program first 
(Refer to Paragraph 600.3). 
If any CO line features are to be changed: 
A Press FLASH and dial [40]. The following mes- 
sage is shown on the display phone: 
Program button 12 (SLCT)...

I -- Hybrid Key Telephone System BARPLUS@ 2448EX 
CO LINE PROGRAMMING (Cont’d) 
A. DTMF/Dial Pulse Programming 
Programming Steps 
1. Press the DTMF flexible button (Button #I). 
l LED on = DTMF enabled 
l LED off= Dial Pulse enabled 
2. Press the HOLD button to enter data. 
B. CO/PBX Programming 
Programming Steps 
I. Press the CO flexible button (Button #I2). 
l LED on = CO type is enabled 
.* LED off= PBX is enabled 
2. Press the HOLD button to enter data. 
C. UNA Programming 
Programming Steps 
1....

sTARPLUS@ 2448EX Hybrid Key Telephone System 
CO LINE 
PROGRAMMING (Cont’d) 
0. 
1. 
2. 
3. 
E. 
1. 
2. 
3. 
Loop Supervision Programming 
Programming Steps 
Press the SUPV flexible button (Button #4). 
Enter a onediiit timer value on the dial pad 
between 1 and 9 which corresponds to 100-900 
msec. 
Press the HOLD button to enter data. Description 
SUPV. Loop supervision is used primarily with 
DISA, Voice Mail/Auto Attendant and with unsuper- 
vised conference applications. A provides the sys- 
tern...

t -. --~ 
i Hybrid Key Telephone System sTARPLUS@ 2448EX 
CO UNE PROGRAMMING (Cont’d) 
F. Flash Timer Programming 
Programming Steps 
1. Press 
the FLASH flexible button (Button #6). 
2. Enter a two-digit timer value between 01-20 
which 
corresponds to 1 OOmsec-2 seconds. 
3. Press 
the HOLD button to enter data. 
G. Line Group Programming 
Prorrramming Steps 
1. Press the GROUP flexible button (Button #7). 
2. Enter a one-digit value between l-8 which cor- 
responds to Groups l-8. 
3. Press 
the HOLD...

i 
t 
A sTARPLUS@ 
2448EX 
Hybrid Key Telephone System 
CO LINE PROGRAMMING (Cont’d) 
H. Class of Service (COS) Programming 
1. 
2. Programming Steps 
Press the COS flexible button (Button #8). 
Enter a one-digit value between 1-5 which cor- 
responds to five possible class of service to 
which a line may be assigned: 
COSl = No restrictions. 
COS2= Table A governs, Station COS 2 and 4 
are monitored. 
COS3= Table B governs, Station COS 3 and 4 
are monitored. 
CO%= Restricts 0,l ,‘,# dialed as first...

+ 
I 
Hybrid Key Telephone System sTARPLUS@ 2446m 
CO LINE PROGRAMMING (Cont’d) 
I. Direct Ringing to UCD Groups 
Programming Steps 
To assign ringing of a CO line directly into a UCD 
group: 
1. Press the UCD flexible button (Sutton #9). The 
following message is shown on the display 
phone: 
2. Enter the three (3) digit UCD group pilot number 
(890-897) of the UCD group desired. 
3. Press HOLD button. The following message is 
shown on the display phone to indicate current 
programming 
of that line or...

1 
1 
sTARPLUS@ 2448EX 
Hybrid Key Telephone System 
,--Y 
SECTION 630 
STATION AlTRIBUTES PROGRAMMING 
‘. 630.1 STAlION PROGRAMMING 
Programming Steps 
If the system is in the programming mode, continue 
using program codes. if starting to program here, 
enter the programming mode first (Refer to Para- 
graph 600.3). 
if station features are to be changed: 
A Press FLASH and dial [50]. The following mes- 
sage is shown on the display phone: 
Program button twefve (SLCT) will be lit. Enter 
a six digit...