Vodavi Starplus 2448ex Hybrid Key Telephone System Installation Manual

- 
Hybrid Key Telephone System =ARPLUS@ 2446EX 
analyzing and manipulation of the number takes only 
a fraction of a second from the time the station user 
begins to dial until the number is dialed out over the 
public network lines. 
If no lines are available in any of the CO line groups 
programmed for that mute and allowed to that sta- 
tion, the call can be automatically queued on to the 
first choice (least costly) line group. If the user waits 
three seconds after dialing the number, they will hear...

~ARPLUS@ %‘t8u( Hybrid Key Telephone System 
7 
LCR PROGRAMMING (Cont’d) 
C. LCR Programming 
Programming Steps 
If you are in 
the program mode, continue using the 
program codes. if you are starting to program here, 
enter the program mode first. 
NOTE: LCR must be disabled while pmgramming or 
making changes to any of the LCR tab/es. Refer to 
sec. 610.23 for instn&ions to disable LCR. 
1. To program the system for Least Cost Routing, 
press FLASH and dial [61]. The following rnes- 
sage is shown on...

Hybrid Key Telephone System sTARPLUS@ 2446EX 
LCR PROGRAMMING (Cont’d) 
D. SDigit Area/Office Code Table 
Programming Steps 
1. Press 3-DIGIT TBL flexible button (Button # 1). 
The following message will be shown on the 
display phone: 
Where: 
L = [0] for non leading l(‘1” not dialed) 
[l] for leading l(‘1” is dialed) 
NNN = area/officecode 
RR = route list number 00-15 
6 = [0] do not go to 6 digit table 
[l] go to 6 digit table 
PP = number of digits expected to be dialed. 
2. Press the HOLD button to...

Hybrid Key Telephone System 
LCR PROGRAMMING (Cont’d) 
F. Exception Code Table 
Programming Steps 
1. Press EXCEPT TBL flexible button (Button #3). 
The following message will be shown on the 
display phone: 
Where: 
S = [0] to remove code from table 
[l] to add code to table 
XX= exception codes 
(for single digit codes, press DND button 
as 2nd digit). 
The digits [1 and [#] may be entered as 
valid digits. 
RR= route table number, 00-l 5 
2. HOLD must be pressed after each entry. Dis- 
play will now...

Hybrid Key Telephone System sTARPLUS@ 2448EX 
LCR PROGRAMMING (Cont’d) 
G. Route List Table 
Programming Steps 
1. Press the ROUTE UST flexible button (Button 
#4). The following message will be shown on 
the display phone: 
Where: 
RR = Route List Table number 00-15 
T = Time Period Route list 1-4 
G = CO tine Group l-7 
DD = Insert/Delete Table reference 00-l 9 
(##I for none) 
L= LCR Class of Service (LCOS) 
2. Press HOLD. Display will now update. 
3. To enter additional CO line groups in the same...

mARPLUS@ 2448EX Hybrid Key Telephone System 
 
LCR PROGRAMMING (Cont’d) 
H. 
1. Insert/Delete Table 
Programming Steps 
Press INS/DEL TDL flexible button (button #5). 
The following message will be shown on the 
display phone: 
-1 2. Enter the table information as follows; 
Where: 
lT = Insert/Delete Table Number 00-l 9 
X - [O] Pm-Delete numbers 
(first digits dialed in the number) 
[I ] Pm-Insert numbers 
(insert digits in front of number dialed) 
[2] Post-Insert numbers 
(insert digits behind number...

Hybrid Key Telephone System sTARPLUS@ 2446EX 
LCR PROGRAMMING (Cont’d) 
I. Daily Start Time Table 
Programming Steps 
1. Press the DAILY START flexible button (button 
#6). The following message will be shown on 
the display phone: 
2. Enter times in military form (2400 Hours) in 
succession. Pressing the HOLD bulton after 
each time entered. Default times are 0800, 
1700,230O (8 AM, 5 PM, and 11 PM), and the 
fourth time is disabled (##I#). To change a 
start time all times must be reentered. 
3....

STARPLUS@ 2dd8u( Hybrid Key Telephone System 
LCR PROGRAMMING (Cont’d) 
J. Weekly Schedule Table 
Programming Steps 
1. Press the WEEKLY SCHED flexible button 
(button ##7). The following message will be 
shown on the display phone: 
Where: 
O= Monday 
I= Tuesday 
2= Wednesday 
3= Thursday 
4= Friday 
5 Saturday 
6= Sunday 
‘3 
_ T = Time Period Route List (l-4) to use for the time 
of day (based 
on the daily start time table). Enter 
values for all time periods specified in the daily start 
time table...

- 
Hybrid Key Telephone System %ARPLUS@ 2448Ex 
LCR PROGRAMMING (Cont’d) 
K. Default LCR Data Base 
In an effort 
to decrease installation and set up time, 
usually associated with LCR, a default LCR data 
base has been incorporated. The default LCR data 
base will provide basic muting for local and long 
distance dialing. Default entries have been made in 
the 3-Digit Table for local office codes (NNX’s) and 
all area codes (NPA’s). Two mutes have been es- 
tablished with the default data base for...

STARPLUS%~~~EX Hybrid Key Telephone System A 
-.. 
SECTION 660 
INITIALIZE DATA BASE PARAMETERS 
660.1 
INlTfALlZE SYSTEM PARAMETERS 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.3). 
If System Parameters need to he initialized: 
1. Press PIASH and dial [70]. The following mes- 
sage will he shown on the display phone: Descrfption 
The system parameters may be initialized...