Vodavi Starplus 2448ex Hybrid Key Telephone System Installation Manual

Hybrid Key Telephone System sTARPLUSw 2448EX 
STATION PROGRAMMING (Cont’d) 
R. Display Flexible Buttons 
Programming Steps 
1. Press the DSP flexible button (Page B, Button 
W 
2. The programming assignment on four buttons 
will be displayed starting with the lowest button 
number. With each sub-sequent depression of 
the DSP 
button the next four buttons will be 
displayed. The following message is shown on 
the display: 
Description 
DSP. Any time a display of button programming 
(default or changed)...

~ARPLUS@ 2448EX Hybrid Key Telephone System 
SECTION 640 
EXCEPTION TABLES PROGRAMMING 
640.1 INTRODUCTION 
Programming Steps 
The 2448EX Hybrid Key Telephone System offers a 
flexible means of applying toll restriction to stations 
or indiiduak. Dialii privileges (or toll restriction) 
is determined through assignment of station and CO 
line Class Of Service (COS). Several types of re- 
striction can be derived simply by programming COS 
assignments and CO line access to stations. This 
may, in some...

Table 640-2 Allow/Deny Toll Table 
ALLOW 
TABLE 
ENTRIES 
a 1 followed by an area code). 
The 2448EX system also offers four (4) special 
tables that can be referenced from within the two 
allow tables. Three of the special tables can be 
assigned to specific 
area codes that require further 
toll restriction definition. The fourth special table is 
reserved for use as 
a home area code table (num- 
bers within the same area code as the site where the 
system is installed). This provides expanded ability...

sTARPLUS@ 2448EX Hybrid Key Telephone System 
-. 
643.3 TOU RESTRICTION PROGRAMMING 
A Entering Toll Table Programming 
Programming Steps 
If the system is in the programming mode, continue 
using program codes. If starting to program here, 
enter the programming mode first (See Paragraph 
600.3) 
NOTE: It is recommended tiat the Exception Tables 
be initiakedpriar to entering data into the tabks. Do 
this by rollowing the instructions in Sec. 600.4 for 
initialking the Ekeption Tables (Flash 73). This...

Hybrid Key Telephone System STARPLUS@ 2448EX _ 
Exception Tables Programming (Cont’d) 
B. Allow Table Programming 
Programming Steps 
1. Press the ALL-A or ALL-B flexible button (But- 
ton #I or #3). The following display will be 
shown on the display telephone: 
The first two bins locations are displayed. 
2. Dial on the dial pad the twodigit bin number 
(01-20) the allow code is to be entered into. 
NOTE: It is recommended that; bin 17 be reserved 
for an entry that will reference special table number...

sTARPLUS@ 2448M Hybrid Key Telephone System 
Exception Tables Programming (Cont’d) 
Allow Table Programming (Cont’d) 
Programming Steps 
2. For an enby that is to reference the Home Area 
Code table (special table 4) the entry may also 
be entered to expect or not expect a leading 
digit [l]. In fact in some cases it may be desir- 
able to enter both of the following entries; 
Leading diiit [l] - BB 1 DDD {S} 
an&or 
Non Leading [l] - BB DDD {S} 
Where: 
BB = Bin number (recommended bin 20) 
DDD =...

Hybrid Key Telephone System wARPLUS@ 2448EX ~. 
Exception Tables Programming (Cont’d) 
C. Deny Table Programming 
Programming Steps 
1. Press the DEN-A or DEN-B flexible button (But- 
ton #I2 or #4). The following display will be 
shown on the display phone: 
The first two bin locations are displayed. 
2. Dial the two-digit bin number (01-l 0) where the 
deny code is to be entered into. 
3. Dial the deny code where: 
0 to 9, 
l , # = corresponding deny digits (numbers) 
DND = Don’t Care digit 
4. Press...

sTARPLUS@ 2448EX 
Hybrid Key Telephone System 
Exception Tables Programming (Cont’d) 
D. Special Table Programming 
Programming Steps 
To program a special table it is first necessary to 
assign an area code to the table (except for the home 
area code). 
1. To assign an area code to a special table press 
the appropriate AREA X flexible button (button 
#/9-l 1). The following display will be shown on 
the display phone: 
Enter the three (3) digit area code. 
Press the HOLD button. The display will now...

Hybrid Key Telephone System sTARPLUSa 2448EX -_ 
Except&n Tables Programming 
(Cont’d) 
E. Displaying Toll Table Entries 
Programming Steps 
To display entries in either the Allow /Deny tables or 
the special tables press the DISP flexible button 
(button #12) while entering information into a table. 
1. While viewing entries made into an allow or 
deny table two (2) entries at a time will be 
displayed on the bottom line of the display. By 
pressing the DISP button again the next higher 
bins will be...

~AAPUJS@ 2448EX Hybrid Key Telephone System 
SECTION 650 
LEAST COST ROUTING PROGRAMMING 
A. Introduction 
Least Cost Routing (LCR) selects the most economi- 
cal programmed route for an outgoing call. When a 
station user dials an outside number, the LCR fea- 
ture analyzes the number and then automatically 
chooses an outside line from the group that has been 
programmed as most economical. The LCR feature 
puts the responsibilii of choosing the least expen- 
sive route for each area code and exchange...