Vodavi Starplus 2448ex Hybrid Key Telephone System Installation Manual

Hybrid Key Telephone System %.ARPLUS@ 2448EX 
When using a data terminal (l/O device) to program the system, the following chart presents the data 
terminal characters that are equivalent to the keyset buttons. 
a&n>? 
REflOTE CIDtlIN KW DEFINITIONS 
Keyset Terminal Keyset Terminal 
---------------------------------------- 
HOLD 
FLASH 
.() - - 
1 
3’ 
2 
6 
; 
9 
10 
11 
s 
enable 
disable 
adm> ENTER/CR FLEX 1 
FLEX 2 
FLEX 3 - 
FLEX L) 
FLEX 5 
FLEX 6 
FLEX 7 
FLEX 8 
FLEX 9 
FLEX 10 
FLEX 11 
FLEX 12...

%ARPLUS@ 2448EX 
Hybrid Key Telephone System 
FLEX1 FLEX 2 FLEX 3 FLEX 4 
FLEX 6 FLEX 6 FLEX 7 FLEX 8 
7 
* THIS BUTTON IS MAPPED AS A LOOP BUTTON ON THE BASIC KEYSET 
Figure 600-2 SP 2448 Default Button Mapping 
Issue 3, August 1991  

Hybrid Key Telephone System sTARPLUS@ 2448EX 
Table 600-l Default Values 
FEATURE 
System Hold Recall Timer 
Exclusive Hoid Recall Timer 
Transfer Recall Timer 
Preset Forward Timer 
Pause Timer 
Call Park Timer 
Conference Timer 
MSG Wait Reminder Tone 
Paging Timeout Timer 
CO Ring Detect Timer 
Hold Preference 
Automatic Privacy 
External Night Ring - LBCl 
Attendant Override 
Attendant Station Assignment 
Loud Bell Control 
PBX Dialing Codes 
Executive/Secretary Transfer 
UCD Groups 
SMDR (ON/OFF)...

%‘ARPLUS@ 2448EX 
Hybrid Key Telephone S&em 
Table 60&l Default Values (Cont’d) 
FEATURE PROGRAM 
CODE FLEX BUTTON DEFAULT VALUE 
Over flow Timer 
Button 3 60 sec. 
Announcement Table 
flash 34 
None 
Call Forward No Answer Timer 
Flash 35 15s 
Voice Mail Groups 
Flash 36 Buttons 1-8 None 
Voice Mail Outpulsing Tables 
flash 37 Tables O-7 None 
Disconnect Table 
Table 8 None 
CO tine Programming 
flash 40 
DTMF/Pulse 
Button 1 DTMF 
CO/PBX 
Button 2 co 
UNA 
Button 3 Yes 
Loop Supervision 
Button 4 No...

Hybrid Key Telephone System 
SWWLUS@ 2446EX 
Table 600-l Default Values (Cont’d) 
FEATURE 
Special Table 1 
Special Table 2 
Special Table 3 
Special Table 4 
Least Cost Routing 
3-Digit Routing Table 
&Digit Routing Table 
Exception Code Table 
Route List Table 
Insert/Delete Table 
Daily Start Time Table 
Weekly Schedule Table PROGRAM 
CODE FLEX BUTTON DEFAULT VALUE 
Button 5 Ail Codes Allowed 
Button 6 All Codes Allowed 
Button 7 All Codes Allowed 
Button 
a All Codes Allowed 
Flash 61 
Button 1...

STARPLUS@ 2448EX 
Hybrid Key Telephone System 
7 
600.3 PROGRAM MODE ENTRY (Key Sta- 
tion) 
Programming is performed at station 10 using either 
the Enhanced or Executive Key Telephone. Pro- 
gramming is always done at this station regardless 
of the class of service or which station has been 
assigned the attendant(s). 
Before entering the program mode, the programmer 
must first verify that the Key Telephone is properly 
connected to Station 10. 
To enter the program mode: 
A. 
B. 
C. 
D. Press ON/OFF...

SECTION 610 
.  SYSTEM PARAMETERS PROGRAMMING 
610.1 SYSTEM HOLD RECALL TIMER 
Programming Steps 
If this timer is to be changed: 
A Press 
FLASH and dial [Ol]. The following mes- 
sage is shown on the display phone: Description 
Determines the amount of time before a call 
placed 
on System Hold will recall the station placing the 
hold. If unanswered by that station, the call will recall 
the attendant. 
Default: Default value is 060 seconds and is van’- 
An entry of 000 will disable the timer and...

Hybrid Key Telephone System sTARPLUS@ 2448EX 
SYSTEM PARAMETERS (Cont’d) 
610.3 TRANSFER RECALL TIMER 
Programming Steps 
If this timer is to be changed: 
A Press FLASH and dial [03]. The following mes- 
sage is shown on the display phone: 
6. Enter three digits on the dial pad. 
C. Press HOLD button. Display will now update. 
-. - 
610.4 
PRESET FORWARD TIMER 
Prooramming Steps 
If this timer is to be changed: 
A. Press FLASH and dial [04]. The following mes- 
sage is shown on the display phone: 
6....

sTARPLUS@ 2448EX Hybrid Key Telephone System 
SYSTEM PARAMETERS (Cont’d) 
610.5 PAUSE TIMER 
Programming Steps 
If this timer is to be changed: 
A Press FLASH and dial [05]. The following mes- 
sage is shown on the display phone: Description 
Determines the length of the pause when pn>- 
grammed for use with speed dialing and LCR insert 
Tables. 
Default: Default is 
2 seconds and is variable from 1 
B. Enter one digit on the dial pad. 
C. Press HOLD button. Display will now update. 
610.6 CALL PARK...

Hybrid Key Telephone System =ARPLUS@ 2446u( 
SYSTEM PARAMETERS (Cont’d) 
610.7 CONFERENCE TIMER 
Programming Steps Description 
If this timer is to be changed: 
A. Press FLASH and dial [07J. The following mes- 
sage is shown on the display phone: Determines the amount of time an unsupervised 
conference can continue after the initiator of the 
conference has exited the conference. 
Default: Default is 10 minutes and is variable from~ 
01 to 99 minutes. 
A 00 entry disables the timer and means an auto-...