Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

inJinitew DVX I’Digital Key Telephone System
STATION FEATURE OPERATION
Skip the preceding step for immediate
4. Dial the three-digit ACD or UCD group
pilot number (550-565) for the group 
(l-
16) where calls are to be forwarded. Con-
firmation tone will be heard.
5.Replace the handset or press the ON/OFFbutton.
Refer to Sec. 405.4, Call Forward: Station for
Basic Keyset operation of this feature.*Refer to Sec. 400.37, Flexible Button
Assignment.
To remove Call Forwarding:1. Lift the handset or press the...

STATION FEATURE OPERATIONinfinitem DVX I’Digital Key Telephone System
1.Dial (6031 on the dial pad.
2.Dial the CO group access code for the COLine group to be forwarded,
or
Press an individual CO Line button.
- [81] = CO Group 1
- [82] = CO Group 2
- [831= CO Group 3
- [84] = CO Group 4
- [85] = CO Group 5
- [861= CO Group 6
- [871= CO Group 7
- [88] = All CO Lines
3.Dial the speed bin number that contains
the number where calls are to be for-
warded. Confiiation tone is heard.
To remove Off-Net...

inJinitem DVX I’Digital Key Telephone System
STATION FEATURE OPERATION
c. Press the outside line button or loop buttonflashing on hold.
400.20TRANSFERRING CO CALLS TO A
STATION FORWARDED TO 
VTkl
While connected to a CO line:a. Press the 
TRANS button and dial the ex-
tension nurnber of the station forwarded to
voice mail.
b. The transferring station hangs up. The COcall will be directed to the mailbox of the
forwarded station.
If the trUmfefTiRg station QtteMptS to
supervise the transferorjustwaifs...

STATION FEATURE OPERATIONinfnite’“l DV2C I’Digital Key Telephone System
d. Add next conference party by selecting an-
other outside line or intercom station.e. When party answers, press the pre-pro-
grammed* CONF button twice.
f. All parties are connected.
Exiting a Conference (Controller only)
There are three methods of exiting a conference:
1.Press the ON/OFF button to ON, press the
MUTE button, and replace the handset (to
monitor a conference).
Use the following method only if multi-line con-
ference...

inf%xite~ DVX I’Digital Key Telephone System
STATION FEATURE OPERATION
- (2]= 1200
- [3] = 2400
- [4] =4800
- [5]= 9600
- [6] = 19.2K
- [7] = 38.4Kb.Press the SPEED button to save any
changes made.
To change the character length:a. Press the TRANS button. Then enter the
desired one-digit character length, either 8
or 9.b.Press the SPEED button to save any
changes made.
To change the number of stop bits:a. Press the MUTE button. Then enter the
desired one-digit stop bit, 1 or 2.
b.Press the SPEED button...

STATION FEATURE OPERATIONinfinitem DVX I’Digital Key Telephone System
names are located (found) after 8 digits,
the first one is dialed.l The names will be entered as a part of
the system attributes database. Num-
bers may be entered as part of a name.
To avoid conflicts, all names must have
a unique numerical sequence.400.27 DIRECTED CALL PICK-UP
When incoming, transferred, or recalling out-
side line ringing, intercom ringing, or Camp On
ringing is heard at an unattended telephone:
a. Dial the station...

infznitem DVX I’Digital Key Telephone System
STATION FEATURE OPERATION
selector switch (SLT stations will tone
ring).l If the desired party is associated to a
speed dial bin, the system will select a
CO line and dial the number pro-
grammed into the speed dial bin. Call
progress tones will then be heard.
To Transfer a Call using Directory Dialing:
While on a call:
a. Press the TRANS button.b. Dial the Directory Dial Code 
[680] on the
dial pad,
or
press a pre-programmed* flex button pro-
grammed for...

STATION FEATURE OPERATIONinfinite” DVX I’Digital Key Telephone System
Conditions:l Station users may listen to all tones by
dialing the two-digit codes one after an-other. The tone that is sounding when
the SPEED button is pressed will be
saved as that station’s tone ringing se-
lection.
I
l A station’s tone ringing selection will be
maintained in a battery protected area
of memory. Therefore if a system expe-
riences a power failure, or a soft or hardrestart, a station’s tone ringing selec-
tion will be...

in.nitem DVX I’Digital Key Telephone System
STATION FEATURE OPERATION
Removing Do Not Disturb
a. 
Press the pre-programmed* DND button.
The button LED extinguishes and DND is
canceled.*A flex button must be programmed for this
feature to operate. Refer to Sec. 400.37, Flexible
Button Assignment.A.One-Time Do Not Disturb
Allows you to prevent calls from ringing atyour station while you’re on a call. The
One-Time DND condition will automat-
ically cancel when you end your call.a. Press the pre-programmed*...

STATION FEATURE OPERATIONinfinite’l” DVX I*Digital Key Telephone System
400.37 FLEXIBLE BUTTON ASSIGNMENT
If you have buttons on your telephone which
have NOT been assigned as CO lines, Pooled
group, or Loop buttons, you may program them
to suit your own individual needs. There are fivepossible functions you may assign to these
buttons:
l DSS/BLF: This button, when pressed, will
automatically signal the assigned intercom
station. DSS/BLF buttons are programmed
by the station user.l
FEATURES: This button...