Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

M&e TM Diilbl SystemsTF NO: 58
TruM Card (CotIt’d)
PROGRAMMING Tl ALARM INFORMATION
Press FLASH and dial [47j in the programming mode. The buttons in the FLASH 47 programming mode
are as follows:
The LCD on the telephone displays the following:
Buttons l-7 represent each of the 7 alarm conditions. These alarm settings govern all 
Tl trunk cards installed in
the system. To select a particular alarm press a button (l-7) that represents the alarm condition you wish to Set.
The LED lights steady when the...

intinite m Digiil SystemsTF NO: 58
Tl TN& Card (Cont’d)
For example the procedure for setting all the alarm conditions for Carrier Loss are as follows:Button 
% ll- ENABLE/DISABLE
1.Press Button # 1, to activate the Carrier Loss alarm. The default condition Button # 11 is also lit and the
LCD displays the following message:
:/ &km w:  :  q i::i;:: :.:if:.,:(ii/j: .:::. . :..:,:. ~.:..:i:::. ..:j::.. !*li-:1:..::.:-.-: :::. ,,;;j,,;,,: ,:j .:,,, /1,j:;;::, .:.’ ‘.
Where O-l is the range of numbers that...

infinite TM Digital SystemsTF NO: 58
Tl Trunk Card (Cti’d)Button 
# 13- MINOR ALARM
1.Button # 1 remains lit. Press Button # 13 to enter a value for the alarm.
3.Enter a two-digit value on the dial pad that represents the threshold limit (00-99 Default 15).
This value can be set for all the alarms. The alarms where it should be set are EXC BPV, SLIP, or EXC 
DATA
ERRORS.\
4.Press the HOLD button to confirm the entry. Confirmation tone is heard and the display updates. This
threshold is set for all 
Tl...

int7nite Tb4 Dii*tal SystemsTF NO: 58
Tl Trudc Card (Cont’d)
Button # 15 TIME PERIOD
1.Press Flexible Button #l.
2..Press Button # 15 to enter a value for the alarm.
3.Enter a two-digit value on the dial pad that represents the time period limit (00-99 minutes).
This value can be set for all the alarms. It should be set for EXC BPV, SLIP, or EXC DATA ERRORS.
4.Press the HOLD button to confirm the entry. Confirmation tone is heard and the display updates. This time
period is set for all 
Tl trunk cards in...

infinite m Digiil SystemsTF NO: 58
Tl Trudc Card (Co&d)Button 
W 12- CLEAR ALARM (ANY ALARM)
1.Press the desired alarm button. ( Buttons 1 through 7).
2.Press Button # 12 to clear or disable the alarm. The LCD displays the following message:
Where XXXXXXXXX is the alarm name (i.e. CARRIER LOSS, RED ALARM, BLUE ALARM, YELLOW ALARM,
EXC BPV, SLIP, or EXC DATA ERRORS).
,
3.Press the HOLD button to confirm the entry. A confirmation tone is heard and the display is updated.
The alarm is cleared for all 
Tl...

hfmite TM Digiil SystemsTF NO: 58
Tl Tank Card (Cont’d)Button 
% 14- MAJOR ALARM (ANY ALARM)
1.Press the desired alarm button (5-7).
2.
Press Button # 14 to enter a value for the alarm.
3.Enter a twodigit value on the dial pad that represents the threshold limit (00-99).Where XXXXXXXXXX is the alarm name. This value can be set for all the alarms. It should be set for EXC
BPV, SLIP, or EXC DATA ERRORS.
4.Press the HOLD button to confirm the entry. Confirmation tone is heard and the display updates. This...

inl7nife TM Digital SystemsTF NO: 58
Tl Tnvlk Card (Cor#d)Button 
# 16.. AlTENDANT DISPLAY (ANY ALARM)
1.Press the desired alarm button. (Buttons 1 through 7).
2.Enter 0 (Disable) or 1 (Enable) on the dial pad to disable or enable the alarm.
‘.: .:.::.:g &i’
~::,.:: :...:::; ‘..‘. ./ :
Where XXXXXXXXX is the alarm name (ie: 
CARR!ER LOSS, RED ALARM, BLUE ALARM, YELLOW ALARM,
EXC BPV, SLIP, or EXC DATA ERRORS.)
3.Press the HOLD button to confirm the entry. A confirmation tone is heard and thf LCD display...

hWte TM Digiil SystemsTF NO: 58
Tl Tndc Card (Cont’d)
Inttialiiation of Tl System Parameters
Descr#bn:
This section describes the procedures and steps necessary to initialize the system database returning any
programmed data to its original or default value. The entire system database may be initialized or various
portions of the database may be individually initialized. In addition to initialization of the entire database, a
system reset (Button 
##20) command can also be used.
The buttons on the...

iniinife m Diiltal SystemsTF NO: 58
Tl Truh Card (Cont’d)
Prhthg of Tl System Parameters:
Desaipii:
This section describes the procedures and steps necessary to print Data Base Parameters and various p(#Ons
of the system. A complete description of these instructions is included in Section 775 of the infinite DVX
Digital Telephone System-- General Description, Installation and Maintenance Manual.
With a printer connected to the RS-232C port (Port 
#3) on the Backplane I/O Expansion Module, the currently...

inGnite TM Digital SystemsTF NO: 58
I
Tl Trunk Card (Cont’d)
For a printout of the Tl System Parameters:
PlogramButtonWl:
To obtain a printout of the programmed Tl alarms in the system, use the System database printout function
(Flash 85, Button 
#l).
1.Check to see that Button # 1 is lit.
2.Press the HOLD button. The following message displays on the phone LCD:
/pnlM ’
4
When the system finishes sending the information to the printer, confirmation tone is heard. The
following is a sample report of the...