Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

infinite TM Diiieal SystemsTF NO: 58
Tl TN& Card (CotWd)
Program Button # 2:
Prints out the attributes of each line in the 
Tl channel bank.
1.Press the CO line attribute flexible Button (Button # 2). The following message displays on the phone LCD:
2.Once the system sends information to the printer, the following is a sample report:CO LINE 
ATTkIBUTES
------------------
co 01
-----
LINE 01
SIGNAL TYPE UNA CONF PRIDTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RDNN
lo 113 0
SIG RING DIAL VOL2Y Y7
RING...

PRODUCT NOTICE
PN0023
infinite Digital Systems
October 27,1995AFFECTED PRODUCTS:
SUBJECT:
UPDATES:
1.
2.
4
b)
cl-
d)
Software Version 3.1 jDVX I, DVX II, and DVX 
III Systems
S/w Release for DVX Systems
A change in administration programming has been 
add,ed to SNV version 3.lj and
above. This change is as follows:
On DVX I & DVX ii systems the station ID programming (Page B, button 1) hasbeen changed. Station ID 7 now reflects a relay/sensor box and Station ID 8
now reflects a 
DDIU unit. The complete...

PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
PN00234Issue 2 of the Technical Manual inadvertently left out information regarding the RAN
Hunt Group feature that was added to FP3 software. This enhancement allows an
ACD RAN to be directed 
+o a hunt group to permit up to eight (8) callers to receive
the RAN announcement at a time. There can be up to four (4) RAN hunt groups in
the system.Programming hunt groups:
1.At station 100, dial **3226.
2.Press the FLASH button and dial 30.
3.The button layout for Hunt...

PRODUCT NOTICE
INFINITE DIGITAL SYSTEMS
PN0023
Conditions:1.
2.
3.
4.
5.RAN hunt group pilot numbers are 458-461.
RAN hunt group numbers can be chained together by placing theRAN group number (458-461) as the last member in the desired
group.
Hunt group pilot numbers 458-461 are reserved exclusively for RANfunctions. Both guaranteed and regular RAN announcements can
be directed to a RAN hunt group.
Both guaranteed and regular RAN announcements can be directed
to a RAN hunt group.
4RAN hunt groups are...

INPN0032infinite Digital Systems
October 1997
Revision B
Software Version-3.4 SeriesAFFECTED PRODUCTS:DVX I, DVX II, DVX 
Ill Systems
SUBJECT:
UPDATES:New Software Release for infinite Digital Systems
1.Please note that when the System Speed Dial and Directory Dial areas are
initialized, Station Speed bins will be initialized.
2.A correction was made to allow a Group Pickup buttonlfhat was programmed in
Administration to be used with Directed Call Pickup and be programmed at the
station level.
3.The...

PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN0032
PROGRAMMING LEADING DIGITS:
This feature provides the ability for the system to have the dialing plan modified to
accommodate multiple systems connected via TIE/T1 trunks. The dialing plan is
changed to a four digit access with a programmable leading digit. All Feature AccessCodes (except those starting with 8, 9, or 0) and Station Numbers will be dialed by
dialing the programmable leading digit first followed by the standard dialing plan.
Enter Programming...

PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN0032
CONDITIONS:
This feature is disabled by default.
PROGRAMMING THE LENGTH OF CENTREX DIGITS:
This feature determines the length of 
centrex digits in the system. When a leading
digit marked as Trunk Group Access is dialed, the remaining 3 or 4 digits will be
collected and the system will access the desired trunk group and outpulse the digits.This program determines when the end of dial is by the amount of digits dialed.
Enter programming mode and go to FLASH...

PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN00326.Caller ID Name and Number Display
A new feature has been added to allow a station user to program a flexible button
to enable the user to view both the number and name on the LCD when receiving
a Caller ID CO call. The top line of the LCD will display the number of the caller and
the bottom line of the LCD will display the name.
The user must program a Flexible Button onto their telephone. SPEED + SPEED +
FLEX + 653.If the feature is enabled, LED lit...

-*.PRODUCT NOTICE
INFINITE DIGITAL SYSTEMS
INPN0032
PROGRAMMING:
1.FLASH 09 Button 10123456789012345678901234
~
2.Enter a 3 or 4 on the keypad.
3.Press HOLD
8.Direct CO Access
This feature modifies the way digits are dialed when CO senderization is enabled inthe system. If senderization is enabled in the system, 
thd’system will wait for the
length of the pause timer before sending the first dialed digit. The system will accept
digits from the station as rapidly as the station dials. This applies to...

PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN0032
Station 1100
System A
Trunk Group
connected tcSystem B
Dial 1100 Dial 2101System 
6Trunk Group
connected to
System AStation 2100
Station 
2101
AEXAMPLE APPLICATION:
System A connected to System B via TIE trunks.Program the leading digit 1 (FLASH 09 Button 
1, dial 8 on the keypad) to be a leading digit on System A.
Program the leading digit 
2(FLASH 09 Button 2, dial 8 on the keypad) to be a leading digit on System B.
Enable the leading digit option on...