Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

DELETEBeletlng a ROUTE from the network
First DELEIE the NUMBERING PIAN, then the LOCATION; then
the ROUTE. 

19-4 Configuration Mawal-
19.2ROUTE TABLE FOR REMOTE NETWORKING
Remote networking refers to situations where lbshiba VP Systems are located at different
locations behind different phone systems.
The information in this table specifies the outgoing routes from this location. The information
includes the name of each route, whether the route can be dropped, and digits 
t6access the
route.
Example of the 
RODTB Table:
‘i.
nHow The ROUTE Table Is Used
The ROUTE Table contains the digits required to access...

N - wait for DIAL-UP OCC DIAL TONE here.
P 
- dial PUBLIC NETWORK NUMBER here.
T 
- dial TIE NETWORK NUMBER here.
The D, E, and N are defined system-wide by the factory depending
upon the PBX that the 
lbshiba VP System is connected to. The Pand T are defined in the 
LOC~ON Table. Examples:
l ‘-DDD
Dial 9, wait for dial tone, delay, then dial the mainnumber to reach a location. Enter: 
9EDP
WATSDial 110, wait for dial tone, then dial the main numberto reach a location. Enter: 
1lOEPSPRINT
Dial 111, wait...

19-6 Configuration Mawal-ADD
Adding a ROUTE to 
the network
Fii ADD the ROUTE, then the 
LUCATION, then the
NUMBERING PL4N.MODIFY
Modifying an entry 
h the ROUTE Table
DELETE
Deleting a ROUTE from the network
First DELETE the NUhfBERING PIAN, then the LOCATION, then
the ROUTE. 

20 .
SCHEDULE TABLE
Chapter Contents
Section
20.1
20.2
20.3
DescrbtionPWla
Undemmciing the SCHEDULE table...................................................20-lHow the SCHEDULE Tables Are Used..................................................20- 2
How to Configure the SCHEDULE Table................................................20-3.Using INSTALl.................................................................
m-3
Using UPDATE..........
........................................................20-4
ij...

INTRODUCTIONThe SCHEDULE Table allows up to eight different specified time periods plus a default time
period to control the behavior of 
mailboxes and ports..‘-l
A time period coIlsists of the days of the week, start and stop times of the day, and any
holidays.l
The default period consists of all days and times not specified in the prior periods.
Eachcoshasanassociated SCHEDULE Table. The SCHEDULE Table number is the same as
the COS number. For example, SCHEDULE Table 3 contains the 
time periods for...

Quick Reference Guide
SCHEDULE Table
CommandDescriptionSCHEDULE Table
Directs the Toshiba VP System to different
INFORMATION Tables by time 
of day and day of week.The SCHEDULE Table is always the same number as the
cos it is
associated with.
Number of
SCHEDULE Tables128 (o-ln)*
Number of Time
Periods8
Defautt INFORMATION
Table1Used for all 
davs and times not defmed in a time period.
SCHEDULE Table and the
INSTAU. Program
An empty SCHEDULE Table appears for each COS
assigned to ports or 
mailboxes....

SCHEDULE Table 2V-1-
20.1UNDERSTANDING THE SCHEDULE TABLE
SCHEDULE Tables allow for additional flexibility in answering and handling calls.SCHEDULE
Tables are used for both ports and mailboxescI.-l
SCHEDULE Tables for ports, for example, allow the ability for company greetings and
intercept positions to change by time of day and day of week.
.--
eSCHEDULE Tables for mailboxes, for example, allow the ability to change the number of
times a phone rings during the day and after-hours; or to change the...

20-2 Configuration Mawat-
20.2HOW THE SCHEDULE TABLES ARE USED
SCHEDULE Tables are used to change the way ports and mailboxes behave. The behavior is
changed by time of day and day of week.
The change in behavior results from a 
diffqent
INFORMATION Table being used for the time and day specified.INFORMATION Tables c&in
indexes that determine specific port and mailbox behavior.
The COS assigned to a port or mailbox directs the 
Toshiba VP System to the SCHEDULE Table of
the same number. Each SCHEDULE...

SCHEDULE Table 20-3
20.3HOW TO CONFIGURE THE SCHEDULE TABLE
Defoe a SCHEDULE Table with a matching number for each COS to be used in the PORT and
USER Tables.
Each 
SCHEDULE Table consists of eight possible time periods (numbered 1 through 8) and a
default period. Specify for each time 
period:
lThe days of the week (or HOL for holiday)
lThe times of the day to start and end (in 24-hour time)
lThe number of the INFORhMTION Table to use
Since the default period 
cOvers all times not specified, only define...