Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

ALTERNATE TRANSFER COMPLETE CODE
19MAILBOX NUMBERS MATCH USER EXTENSIONS
Refer to the USER Table chapter for details.
VThe values in parameters 22 through 25 apply to new mailhxes only.22
DEFAULT MESSAGE WAITING START HOUR
23DEFAULT MESSAGE WAITING END HOUR
25DEFAULT MESSAGE WAITING RETRY PERIOD (MINUTES)
25
28
31DOUBLE-INTERRUPTED RINGBACK
Iu-The ‘D” character is equal to 5 times the normal delay contained in
System Parameter 
28ALARM NUMBER1 

SYSIEM PAFtAMfZ!ER Table22-1332
MAXIMUM MESSAGE LENGTH (MINUTES)
33
- _43
45
46SYSTEM RELOAD CANCEL-FORWARD STRING
51
56
llisisthemaxixnum recording length of a message sent to a n&box. For a ’
discusbn of the maximum recording length that can be recorded from a
mailhaq refer to CONFIGURXI’ION, INFORMATION Table, Index 22.-
The maximum message length is 3 hours. The length of messages and greetings
is controlled by the INFORMATION 
Table. If a value is not defied in the’
INFORMATION Table, the default is...

22-14 Configuration Maorra/
-
lPIf your system encounters anexCeSiiYe number of NO DIAL-TONE and
it is caused 
by the PBX not giving DIAL-TONE after flash, increasing
retry attempts may improve the 
excessrate. Refer to peg 13 in the
IlLst~mrdMointeMnccmand- bMNTENANCE,TiaffiiPegcount 
nble
mm 59
IftheanswerisYESthesemndprtofthisqmstionisasked. Onlyonecabinet
perPBXcxnbedefinedasthemaste.rsyaem.
DID: SYW PILOT EXiENSlON NUUBER
mm 60DID: AITENDANT DCbENSlON NUMBER
DID: NUMBER OF DIGITS EXPECTED FROM CO62...

67NRt MAX BEEPS FOR REMOTE CONNECT (NT Option)
Determines the number of DTMF A tones the Toshiba VP System sends before
determining that the other location is not answering. The value may only be
listed; the default is 20 attempts
68NET REMOTE DELIVERY AlTEMPT LIMIT (NT Option)
Determines 
the number of times the Toshiba VP System attempts to se@ a
message to another location before it returns it to the creator. The value may
only be listed; the default is 20 attempts.
69NEE REMOTE DELAY BEFORE RETRY...

22-l 6Configuration hb-ud
-
This parameter applies to messages left after calling a busy and/or no answer
extension, messages 
kft after greeting, quick messages (IntraMessaging option)
and scripted prompt responses 
(Saipted Prompting option).
75SUBSEQUENT SILENCE MAX SEC (QUICK/SCRIPTED)
7677
PBX PROVIDES MOMENTARY DISCONNECT
78
79
80
LAMP MW: ‘ON” POST-UCIENSION DIGITS
This parameter applies to messages left after calling a busy and/or no ahswer
extension, messages left after greeting, and Quick...

81
82LAMP Mw: IOFF’ POST-EXENSION DIGITS
83
- -84
85
86
87
88LAMP 
Mw: YFF” PRE-DtTENSION DlGlTS
LAMP 
MW UGHT LAh4P FOR EACH NEW MSG
LAhiIP Mw: CALL EXTN BEFORE UGHnNG IAMP
RECONNECT CODE AFTER 3RD PARTY HUNG-UPCALLERS GET MUSIC-ON-HOLD
07This is PBX dependent.
MAXIMUM RETRIES WHEN FIFO QUEUEING(Only applies if Next 
Mailbox is defined. If not, allows caller to continue
-9-dNET! INITIAL-DIGITS INCLUDE MBOX 
1ST DIG
Always set this parameter to NO. 

89NET. USE TRUNK RECONNECT CODES (NT Option)
lf set to YES, the Te VP System uses System Parameters !30,91, and 92 for’
trunk reconnect. If not set or set to NO, the 
T&shiba VP System uses SystemParameters 
I3 and &, values are YES or NO; the default is NO.
90NET RECONNECT CODE AFTER TRUNK ACCESS (M Option).+
De&es the sequence of events (eg., flash, F; expect dial tone, E; delay, b; etc)
the lbshiba VP System uses to reco~ect to the caller on hold after accessing anoutgoing 
trunk. This is PBX...

SYSlEU?AXRAMElE~Table Z-19
m =-- 95
PBX ACCEPTS DTMF DIGITS ON DID TRUNKS
96MOVE BACKWARD DURING GREEllNG (BLOCKS)
97
- __ 96
99
100
101
102
103MOVE FORWARD DURING 
GREEllNG (BLOCKS)
LANGUAGE TYPE
DIf the system uses French language prompts, select “!I”
RINGBACKS BEFORE ANSWERING CX PORT
07Only modify this parameter if using AUCal.led party Identification.
RINGBACKS BEFORE ANSWERING MX PORT.,
lUOnly modify this parameter if using AI/Called Rq Identification.
DELAY BEFORE TURNING ON DTMF REPORTlNG...

104
105
106
107
108
. .
mm .- 109
mm110
111
112
NRt MULTI-CAB DELAY BEFORE DTMF SIGNAUNG
Determines the intenal (in seconds) the Xxhiba VP System waits before sending
DTMF A tones to a multi-cabinet location. Wues are 0 - 20 seconds; the
default is 0 seconds.
DEFAULT SECURllY CODE FOR MAILBOXES.‘-
tt7 XXisthevaluesetinSystemPara;neterl~--MDJIMUM~
FOR SECUXIY CODES. NONE is not allowed if the minimum length
is greater than zero.
LAMP MW-.-.ORT FOR LAMP MESSAGE WAITINGPBX NEVER GIVES 
PARTlAL RINGBACK OR...

113BZ?OnIy mod@ this parameter if integrated with the PBX
MAX SILENCE FOR SPECIAL PURPOSE GREETINGS (SEC)
;m =q114DEVz DELAY BEFORE INTERCEPTING CALLS
BIPWhen exiting UPDME aftex mcxS$ing this parameter, the VP
3oosM3oprompts:115
SYSI’EM SAYS ON-THE-PHONE INSTEAD OF IS-BUSY
mThis parameter is effective only if a name is recorded for the maiIlxx I,t
doe-s not apply if the retry on buy count is non-zero, or if FIFO CallQueuing is set up for the mail-
-m
116SHOULD INTEGRATION BE ACTIVATED?
LL;rThe type of...