Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

21-2 Configuration Manuai
JZxample of a SLOTS Table: 

n tine Card Slots
Slots Al-Al2 may be used for Line Interface Cards (LIC), Telemarketing Line Cards (TLC),
andDirectAccessCards(DAC).Eachlinecardhasfourports,givingamadmumof48ports
in a VP 3oosNp 300 cabinet. Bach port is physically counected to a PBX extension (a single
line)via2i-paircableandaconnedorblock.ThePBXdirectscallstotheVP300sNP300
for answering..--
~flConsult Toshiba Telecom Product Marketing for availability of the Telemarketing Line
Card (TLC), Direct Access Card (DAC) and Mite1 Integration...

mailboxes with specific COS. A default link may be qxcifkl to perform Message Waiting
Notification for all mailboxes with a COS not allocated to a specific message waiting link
Only one default 
link may be specified for the entire q-stem.
If System Parameter 170 is set to NO, the 
first available integration link confgqred for
message waiting is used to turn ON/OFF a message waiting lamp.
The 
SUITS Table contains information about each integration unit on the c&I Entries for
each integration card...

21.2HOW THE SLOTS TABLE IS USED
The SLOTS Table is used to configure each port on a line card and integration card.n tine Cards
Each VP 3OWVP 300 port on a line cud is normally conneded to a specif’ic PBX qtension.
For non-integrated systems, the port extensions must be set up in one or more hunt groups in
the PBX. Each hunt group can be 
con&u.red to handle calls differently. For integrated
systems, refer to the 
Innollatio and Mae manual- ADAPTIVE INTEGRATION, for
configuration details.
- _The...

21-6 Configuration Manual-
thqrwishtoreach,orwaitonthelineforassistance.Whenthe
callerentersanumber,theVP3XMVP300saysz “lhv&youJirdu
?nommr.... ”Tke VP 3iMdVP 300 then puts the caller on hold and.
attempts to call the extension. If the personal greeting is ON, the
VP 3COdVP 300 gives the greeting immediately and does not calL. . . .
CX Mode- Secondary Answering
CX can be used for non-integrated Centrex instaUation&x PBX
DID instalktions, whereby cabs are fonvarded to a.
VP 3OOdW 300 grating after...

SLOTS Table a-7
IflSome PBXs have the capability of running diagnostics on their
pass. The diagnostic may cause the VP 3lOdW 300% self&t
tofailandplacetheVP3OOsNP3OOportinTSTmode,taking .
the port out of service. The port remains in TST mcde until
selftestrunsagainandisabletoputtheportinse~or,.:
until the system is restarted. In these cases, selftest can be
disabled.
This problem has been identified on the Old Disc&er III and
the Ericsson Prodigy. ‘Ihis field should be YES unless you
have consulted with...

B-8 Configuration Manual
DEFAULTDefimes a link as the system default link to perform message waiting
notification for 
alI COS not allocated to a specific link. Currently,
this field applies only to 
AIXT System 75Befinity Gl and Al3tTSystem 
85AXinity G2 integrations
cos
WSystem Parameter 170 -INTEGRATION ON/OFF UN-K MUST
MATCH, must 
be set to YES for the default link and link
defined for qecific Classes of Sexvice to take effen
.‘-
Defmes the Classes of Sewice for which the link will perform
message...

21.3HOW TO CONFIGURE THE SLOTS TABLE
Beginning with slot Al, amfigure the slots used for line cards in consecutive order, without
skipping any slots within the group 
of line cards.
Beginning with slot 
A9, reserve any slots needed for future cards. Then, amfigure integration
card slots in consecutive order, without skipping any slots within the integration cards.
If the VP 
3OOsM’ 300 ax@uraUon includes VF%&, configure the VI%& At2 card in slot Al2
m tine Cards
Each port co~ected to a PBX extension can...

TEST 21-l 0Configuration Mamat-
ports are idle.lf more than 32 ports are configured, the
VP 
3lXldVP 300 makes outcalls when at least four ports are idle..
VFor AT&T System 75 integrations, all ports defmed as YESare 
used for outcalls, with no restrictions
Enter YES or NO to enable or disable the VP 3OOs/VP 300’s selftest
rOUthe.I-
VFor message waiting notification or alarm outcalls, multiple
calls cm be placed simultaneously. The Toshiba 
VP System
places only one network 
outcall at a time.n...

SLOTSTaMe 21-11
D Using INSTALL
Question number 3 in the INSTALL program prompts for slot configuration data, beginning
with slot 1.
m Line Cardsl
The follo6ing is the II&TAIL program SLOTS Table question for line card slots.
.:-
When information for a port is the same information entered for the previous port, onlythe extension number of the port need be entered followed 
by-]. The information
for the remainder of the line is automatically entered.
[~7Configure the slots in order; do not skip any slots....