Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

22-22 cordiguration Manwl
121E&M: SYSTEM PILOT EXlENSlON NUMBER (DIRECT)122
E&M: SYSTEM PILOT -SION NUMBER (DIRECT)123
124E&M: 
AmNDANT EXIENSION NUMBER (NE-WORK)
125
128
127
128
129
130SEND DTMF A TONES FOR FORWARDED CALLS
131E&M: ATTENDANT 
EXIENSION NUMBER (DIRECT).--,._.-.
E&M: NUM OF DIGS BEFORE LOC. CODE (NETWORK).-.
E&M: LOCATION CODE
SEND MBX TO PBX RAWER THAN EXTENSION
LIMIT ON LINE QlJALlTY TEST
Determines the minimum signal level acceptable to receive a network message.
Values are 10-255; the...

SYSTEM PARAMETER Table 22-B-
,iDYThis parameter requires a PBX integration with Loop Current Interrupt
SettoYEs.132
SPEAK SYSTEM PROMPTS FOR FIFO QUEUEING
UT System Parameter 133 is not applicable for lbshiba VP Systems.133
134
140
IL7Used only with Teknekron PBX.
MAXIMUM FORWARDING DEPTH
141CAN USE ZERO AS 
WILDCARD IN NAME
142MINIMUM LETTERS REQUIRED FOR NAME
143144
mm145
INTEGRATlON CARD EXTENSIONIGNORE DTMFS 
AFIER ENTERING mNSION NUMBER
LEADING DIGIT OF PERS-DIST-LIST NUMBER
This 
parameter cannot...

22-24 Configuration Manual147
149
149ALLOW 
BLIND TRANSFER TO PERSONAL ASSISTANCE*150
REMOVE LY=ONNECT” FOR ANNOUNCE TO INTERCEPT
151
REMOVE “STATUS” FOR ANNOUNCE TO INTERCEPT152REMOVE NETWORK PROMPT FOR QUICK LOGON
154155
NAMES DIRECTORY MAILBOX
MITEL CHANNEL FORWARD EXTENSION
E? Ift.hisparameterissettoYES,thesystemdoesablindtransfertoPA
based on COS Attribute 15 or 34. If neither attribute is assigned, a blind
transfer is not 
pfxformed.
Determines if network access prompt should be offered on...

set to YES, the ‘Rshiba VP System ignores a loss of loop current at the
start of a call for the time 
interval specified in this parameter. If no line
current is flowing after this time, the Toshiba VP System treats this as ‘if
a loop current has been interrupted.156
APPUCATlON PROCESSOR MESSAGE POOL DISTRlBlJTiON LIST
olhvorks)157
SPEAK DISCRETE VERSIONS OF NUMBERS 21- 59
IvThis parameter is used only for German language prompts.158
OFFSlIE MW CALL LlMlT ABSOLUTE NOT DAILY
L!YThis parameter works in...

22-26 Configuration Mawal
162
163
164
166167
168
mm169
m-170
VOICE SECTORS TO DELETE ON BUSY DETECT
iflThis parameter is used to erase slow busy tones from the end of a
message. (12 sectors 
- 1 second)
VOICE SECTORS TO DELETE ON FAST BUSY DETECTa.-
Il;rThis parameter is used to erase fast busy tones from the end of amessage. 
(I.2 sectors = 1 second)
USE 24-HOUR CLOCK FOR REPORTS
LAMP 
MW TURN OFF ONLY IF NO MESSAGES
SPEAK AUTO COPIED MESSAGE PROMPT
TALK-DETECT THRESHOLDThis parameter cannot be...

mm173
BModification of this system parameter requires a system FESTAKI
APPUCATlON PROCESSOR BK/FD/PS DURING SPEAK (VPworks)
176
FlXED LENGTH FOR DTMFINT SOURCE FIELDS
177
178
179
180
Some system confiitions require that the same integration link used to turn
ON the message waiting lamp be the link used to turn 
OFF the lamp. Also,.
when more than one PBX of the same type is connected to a single VP
300sNP300cabmet,itisnecessaryto~whichlinkistobeusedforeach
user. Refer to the SLOTS Table chapter....

181MAX PROTOCOL 2 MSG LENGTH (BLOCKS)
Determines what length mesages are returned to senders. The default is 255
blocks. 

23 .
TRANSLATION TABLE
.-
Chapter Contents
SectionDescridionPlWg
23.123.2
23.3
urdwstanding the TFMNSLATION TABLE. . . . . . . ..~.~.......~........................~.~-lHow the TRANSlAilON Table is Used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-2
How to Configure the TRANSIATION Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..e.....e....23-3Using UPDATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

INTRODUCTION
The TRANSLATION Table may be required in certain Adaptive Integration instalhtions. The
TRANSLATION Table allows the Toshiba VP System to translate digits dialed fo~jncoming calls
into the 
‘Iixhiba VP System mailbox numbers 

Quick Reference Guide
TRANSLATION Table
TFtANSLATlON TableCommand
DescriptionMay be required in certain Adaptive Integration
installations.
TRANSLATlON Table and the
INSTALL ProgramThere are no questions in the INSTAU program
pertaining to the TRANSLATION Table. To
configure the TRANSLATION Table, use the
UPDME program.*
UPDATE Command Options
LIST.L 
TRANTo list the TRANSLATION Table.
ADD.A TFfANTo add digits to the TRANSLATION Table.
DELETE.D TFL4NTo delete digits from the TRANSLATION Table.
The ....