Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

Toll Restriction
Program 48 – Station Toll Restriction Classification
Strata DK Programming 5/994-39
Toll Restriction
Program 48 Overview
This program assigns a combination of Digit Restriction and Station Restriction to each station 
port defined in the system. 
Digit Restriction
If Digit Restriction is enabled for a particular station, the station is able to dial the number of digits 
defined in the Program 45-1 Toll Restriction dialing plan.
©Enter 1 in the Digit Restriction column to enable Digit...

Toll Restriction
Program 48 – Station Toll Restriction Classification
4-40Strata DK Programming 5/99 

Strata DK Programming 5/995-1
Least Cost Routing
Least Cost Routing5
The following provides you an overview of the Least Cost Routing (LCR) feature and step-by-step 
instructions to fill in the Least Cost Routing System record sheets. The quantities of LCR plans, 
CO line groups, etc. vary between processors. This chapter and the LCR record sheets note these 
differences when they exist.
LCR enables the system to automatically route each outgoing voice call over common carriers and 
selected lines. The...

Least Cost Routing
LCR Conditions
5-2Strata DK Programming 5/99
Timeout after 0 (Zero)
Notifies the system of the time delay to the user after dialing a 0, before a regular operator is 
accessed.
Area Code and Office Code Exceptions
Separate area code tables and office code exception tables (quantity listed below) can be defined - 
one for each available call routing plan. Each table defines the area codes that are handled by the 
particular routing plan. According to the tables defined, specific...

Least Cost Routing
LCR CO Line Programming Reference Table
Strata DK Programming 5/995-3
Least Cost Routing
LCR CO Line Programming Reference Table
1. Use Program 16 to assign CO lines in groups per the reference table below.
2. Use Program 40 to allow CO line access to stations using LCR for outgoing calls.
3. Use Program 41 to deny outgoing CO line access, except for LCR access.
Important!Area code and office code structure must be defined by Toll Restriction Dial Plan 
for LCR to work properly.
4. Use...

Least Cost Routing
Program 50-1 – LCR Parameters
5-4Strata DK Programming 5/99
Program 50-1 – LCR Parameters
Processor Type:DK14, DK40i, All RCTUs
Program Type:Least Cost Routing
Initialized Default:All LEDs OFF
Program 50-1 Overview
This program defines general operating parameters for LCR software.
lProgram 40 denies CO line access via LCR, but denies all other access methods.
lProgram 41 allows CO line access via LCR, but denies all other outgoing access methods: 
(#7001~#7200, 801~816, Line button)....

Least Cost Routing
Program 50-2 – LCR Home Area Code
Strata DK Programming 5/995-5
Least Cost Routing
LED Button 04: Dial Tone After LCR Access
LED 04 ON: Station users hear a simulated dial tone immediately after dialing the access LCR 
code (typically 9), until the first digit of the phone number is dialed. The dial tone is simulated to 
assure the user of the system’s proper operation, but it is not a functional dial tone.
For HMIS, set LED 04 ON.
If LED 04 is OFF, station users hear nothing after...

Least Cost Routing
Programs 50-3 (1~5) – LCR Special Codes
5-6Strata DK Programming 5/99
Programs 50-3 (1~5) – LCR Special Codes
Processor Type:DK14, DK40i, All RCTUs
Program Type:Least Cost Routing
Initialized Default:911 in 31, all other codes blank
Programs 50-3 (1~5) Overview
This program allows special 1~4 digit codes such as 911 to be routed over the local call route 
immediately when dialed. If Enhanced 911 (E911) is required, E911 programs should be used 
instead of this program.
You can enter...

Least Cost Routing
Program 50-4 – LCR Long Distance Information (LDI) Plan Number
Strata DK Programming 5/995-7
Least Cost Routing
Program 50-4 – LCR Long Distance Information (LDI) 
Plan Number
Processor Type:DK14, DK40i, All RCTUs
Program Type:Least Cost Routing
Initialized Default:See the legend below
Program 50-4 Overview
Enter the number of the LCR route plan over which long distance information calls will be routed. 
Typically, long distance information calls are routed over the local call route...

Least Cost Routing
Program 50-5 – LCR Local Call Plan Number
5-8Strata DK Programming 5/99
Program 50-5 – LCR Local Call Plan Number
Processor Type:DK14, DK40i, All RCTUs
Program Type:Least Cost Routing
Initialized Default:See the legend below
Program 50-5 Overview
The Local Call Plan handles special codes and operator calls. Of the 16 Route Plans available for 
LCR call processing, define one as the Local Call Plan, typically Route Plan 1. Enter the number 
of the plan over which local calls,...