Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

Least Cost Routing
Program 55 – LCR Modified Digits Table
Strata DK Programming 5/995-19
Least Cost Routing
Program 55 – LCR Modified Digits Table
Processor Type:DK14, DK40i, All RCTUs
Program Type:Least Cost Routing
Initialized Default:See each program in the Program 55-X series
Program 55 Series Overview
This program defines call handling so the route definition used by LCR is invisible to the station 
user. The station user handles all calls the same way. The goal is for LCR to remember the dialing...

Least Cost Routing
Program 55-0 – Delete Number of Digits From the Front of Dialed Number
5-20Strata DK Programming 5/99
Program 55-0 – Delete Number of Digits From the Front 
of Dialed Number
Initialized Default:All tables blank
Program 55-0 Overview
Enter the quantity of digits that should be deleted from the front of the number dialed for each of 
the Table Numbers in the Delete Digits Table. The maximum number is 10. Always make the entry 
two digits.
If the Delete Digits Table is activated, refer to...

Least Cost Routing
Program 55-1 and 2 – Add Digits Before and/or After the Dialed Number
Strata DK Programming 5/995-21
Least Cost Routing
Program 55-1 and 2 – Add Digits Before and/or After 
the Dialed Number
Initialized Default:Leaves all tables blank except Delete Digits, which are all 00




  6SNU   +ROG  6SNU ‡‡‡ +ROG 6SNU+ROG 6SNU+ROG
Pause Entry Reference (Programs 55-1, 55-2)
Key/LEDPause (Seconds)Record EntrySpecial Functions
08 16 P8Key/LED 09 (R4.15)
ISDN Start Key, LCD =...

Least Cost Routing
Program 55-1 and 2 – Add Digits Before and/or After the Dialed Number
5-22Strata DK Programming 5/99
Program 55-1 and 2 Overview
Enter the digits that must be added to the front of the number dialed in the Add Digits Table. The 
maximum digits is 22, including pauses.
©Length of pause can be indicated by using codes (P1~P8) specified in the Pause Entry 
Reference Table. Each pause takes two digits of memory space.
©Try to allow for the longest wait, e.g., make the pause longer, rather...

Least Cost Routing
Program 56 – LCR Station Group Assignments
Strata DK Programming 5/995-23
Least Cost Routing
Program 56 – LCR Station Group Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:Least Cost Routing
Initialized Default:Assigns all stations to Group 1




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
ProcessorPort RangeLCR Station GroupsProcessorPort RangeLCR Station Groups
DK14 000~009 1~4 RCTUBA/BB 000~079 1~4
DK40i 000~027 1~4 RCTUC/D 000~239 1~8
RCTUA...

Least Cost Routing
Program 56 – LCR Station Group Assignments
5-24Strata DK Programming 5/99
Program 56 Overview
The purpose of this program is to assign all defined station ports to one of four or eight LCR 
Station Groups (see Program 56, record sheet notes). 
©Station groups are completely independent of one another. Therefore, each station group must 
be defined separately.
©Software does not automatically assign the highest, all-inclusive routing priority to Class 1 
stations, making all routes...

Strata DK Programming 5/996-1
Automatic Call DistributionAutomatic Call Distribution6
This chapter provides ACD programming information for the Strata DK424 system and its 
stations. ACD is not available for the DK14 or DK40i.
The programs specific to ACD are listed below.
©Program 03 – RSIU, RSSU, PIOU, or PIOUS ACD/MIS Slot Assignments
©Program 09 – Auto Attendant Prompt/ACD Group Assignments
©Program *09 – ACD Group DID/Tie Line Digit Assignments (use if Program 71 is not used)
©Program 10-4 – ACD...

Automatic Call Distribution
Program 03 – RSIU, RSSU, PIOU, PIOUS ACD/MIS Slot Assignments
6-2Strata DK Programming 5/99
Program 03 – RSIU, RSSU, PIOU, PIOUS ACD/MIS Slot 
Assignments
Initialized Default:n/a
Program 03 Overview
This program is for specifying RSIU, RSSU, PIOU, or PIOUS ACD/MIS Slot Assignments.
If MIS output is required for ACD, set Code 42 for the slot in which the RSSU, PIOU or PIOUS is 
installed, or Code 49 if RSIU is installed in slot 11 (that connects to the SMIS personal computer)....

Automatic Call Distribution
Program 09 – Auto Attendant Prompt/ACD Group Assignments
Strata DK Programming 5/996-3
Automatic Call DistributionProgram 09 – Auto Attendant Prompt/ACD Group 
Assignments
Initialized Default:n/a
1. Do not use digits 2, 3, and 4, unless the station numbering plan is changed. These numbers conflict with the default station 
[PDNs] of the system.
Program 09 Overview
Program 09 enables you to assign Auto-Attendant (AA) prompt numbers that will route calls to 
specific ACD...

Automatic Call Distribution
Program 09 – Auto Attendant Prompt/ACD Group Assignments
6-4Strata DK Programming 5/99
äTo enter two-digit dialing prompts along with their destination group numbers
1.Enter Program 09. “SELECT” appears on the LCD.
2. Press the desired leading digit. “AUTO ATT DIAL” displays on the LCD.
3. Press

 then the +ROG button. The first digit will now be set.
4. Press 
6SNU, then press a second digit. “AUTO ATT DIAL” displays on the LCD. Enter .
5. Enter the destination ACD Group...