Home > Toshiba > Communications System > Toshiba Perception 1 2 User Manual

Toshiba Perception 1 2 User Manual

Here you can view all the pages of manual Toshiba Perception 1 2 User Manual. The Toshiba manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 131

Overflow Facility 
3. Dial 1. 
4. Dial the DN. 
W The dial tone will stop after the first digit has been dialed. 
W The DN will display under the DEST designation. 
n The LPK LED will light. 
H The dial tone will be heard. 
5. Press them button. 
n The RLS LED will light. 
n The NITE and LPK LEDs will go out. 
NOTE: If a nonexistent DN is dialed, the attendant will hear overflow 
tone. At this point, the B button should be pressed, and the 
correct DN should be redialed. 
When the Overflow Point is the...

Page 132

Overflow Facility 
RELATED FEATURES 
BENEFITS 
2. 
3. 
1. 
2. 
3. When two consoles are being used in a non-tenant system, Overflow 
can be activated and deactivated by either console. 
H The Overflow LEDs on both consoles will light, or go out in 
response to the activation/deactivation from either console. 
In a tenant situation, the specific Overflow destination, as well as the 
specific trunks which are to be routed over the Overflow feature, can 
be assigned independently for each tenant. 
Tenant...

Page 133

Position Busy 
DESCRIPTION Position Busy enables an attendant to “busy out” the console position, in 
order to prevent additional incoming calls from being presented at that 
console position. While the console is “busy,” calls will be diverted to the 
second console. 
OPERATION To Use Position Busy: 
1. Press the m button. 
n The RLS LED will go out. 
n If there is only one console in the system (or the other console is 
in POS BSY), the POS BSY and NITE LEDs will light (the system 
will be in NITE...

Page 134

Push-Button Dialing 
DESCRIPTION 
OPERATION 
PROGRAMMING 
RELATED FEATURES 
BENEFITS The attendant console’s push-button dialpad is used to establish all calls, 
both to the telephone network and within the system. 
The conversion of attendant dialing or speed dialing to either Dial Pulse or 
DTMF signals, is performed automatically by the system. The specific type 
of conversion is dependent upon the particular requirements of the 
outgoing trunk facility. Trunks are provided with either IO or 20 PPS...

Page 135

Secrecy 
DESCRIPTION 
OPERATION 
PROGRAMMING 
RELATED FEATURES 
BENEFITS The Secrecy feature automatically splits the source party from a call 
connection, whenever an attendant either extends the call, or answers an 
attendant recall. If desired, the attendant may either void the split by 
pressing the m button a second time, or alternate between parties by 
using the B and mm buttons. 
Splitting is automatic on all calls that are either extended by, or recalled to 
an attendant. 
1. Whenever a call is...

Page 136

Serial Call (Business Console Only) 
DESCRlPTlON The Serial Call feature is utilized whenever an incoming trunk party needs 
to speak sequentially to more than one party. If this feature is activated by 
an attendant, the trunk party will be held, and the attendant will be 
recalled, whenever a desired internal station disconnects. This enables 
the attendant to then extend the trunk party to the next-desired station. At 
this time, if the trunk party needs to speak to still another party, the 
attendant...

Page 137

Speed Dialing-System 
DESCRIPTION 
OPERATION 
PROGRAMMING 
RELATED FEATURES 
BENEFITS Speed Dialing-System is assigned to a button/LED combination on the 
console, and it enables an attendant to dial frequently-called numbers by 
using abbreviated address codes. A maximum of 90 telephone numbers 
may be stored in the system directory, The attendant also controls any 
changes in the system directory. 
To Make a Call with Speed Dialing-System: 
Press an idle m button.  1. 
2. 
3. n The RLS LED will go out....

Page 138

Splitting 
DESCRlPTlON Splitting permits an attendant to consult privately with either party of a call 
that appears on an attendant console. The feature is automatic on both 
attendant-extended calls and attendant recalls, but can be accessed 
manually at any time by using the B and mq buttons. 
OPERATION AUTOMATlC 
Splitting is automatic on all calls that are either extended by, or recalled to 
an attendant. 
1. Splitting will occur, once an attendant dials a destination party and 
extends an incoming...

Page 139

Spliffing 
To Form a Three-way Conversation from Either an EXCL SRC or 
EXCL DEST Condition: 
1. Press the appropriate m button. 
W The EXCL SRC or EXCL DEST LED will go out. 
n The three parties may now converse freely. 
To Release a Call While in Any of the Above Conditions (Connecting 
the Calling and Called Parties:) 
1. Press the m button. 
W The LPK LED and all call-related displays will go out. 
W The RLS LED will light. 
n The SRC and DEST parties will now be connected. 
PROGRAMMING None....

Page 140

Station Number Display 
DESCRlPTlON The SRC and DEST displays on the PERCEPTION attendant console 
identify any system station which is currently connected to the console. 
OPERATION 1. The Calling Source Number display is a 3-character, 7-segment LED 
display that indicates the number of the calling station or trunk. 
2. The Call Destination Number display is a 3-character, 7-segment LED 
display which denotes the station number or trunk number, which has 
been dialed by the attendant. 
PROGRAMMING...
Start reading Toshiba Perception 1 2 User Manual

Related Manuals for Toshiba Perception 1 2 User Manual

All Toshiba manuals