Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT
7 - 1
7
7. POWER SUPPLY UNIT 
7.1 Output Channel
The followings are five output channels which are n ot linked with the door switch.
1) +3.3V +3.3VA : CN705 Pins 13, 14, 15 and 16 Output to the SYS board
+3.3VB : CN705 Pins 19 and 20
Output to the SYS board
+3.3VB : CN706 Pin 30 Output to the LGC board
+3.3VB : CN708 Pins 9 and 10 Output to the SLG board
2) +5.1V +5.1VA : CN705 Pins 24 and 26
Output to the SYS board
+5.1VB : CN705...

e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNITJune 2004 © TOSHIBA TEC
7 - 2
The followings are two output channels which are li nked with the door switch.
1) +5.1V +5.1VD : CN706 Pin 2 Output to the LGC board
2) +24V +24VD1 : CN706 Pins 11, 12, 13 and 14 Output to the LGC board, PFP/LCF (via LGC board)
+24VD1 : CN707 Pins 15 and 16 Output to the main motor
+24VD2 : CN706 Pins 5 and 6 Output to the LGC board, High-voltage transformer ( via LGC board),
Bridge unit / Job separator / Offset tray (via...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT
7 - 3
7
7.2 Fuse
When the power supply secondary fuse is blown out,  confirm that there is no abnormality with each part 
using the following table.
Voltage Board/Unit Part Fuse type
+24VD1 LGC Main motor F4:8A (Semi time-lag)
Toner motor 
Polygonal motor
Tray-up motor
Internal cooling fan 1
Internal cooling fan 2
Auto-toner sensor
Upper drawer feed clutch
Lower drawer feed clutch
Registration roller clutch
Upper transport clutch...

e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNITJune 2004 © TOSHIBA TEC
7 - 4
7.3 Configuration of Power Supply Unit
 Fig.7-1
PWR-DN 
PWR-EN
+3.3VA 
+3.3VB
+3.3VB
+3.3VB
+5.1VA 
+5.1VB 
+5.1VBCN705 
CN705
CN706
CN708
CN705
CN705 
CN706
+5.1VB CN707 SYS board
SYS board
SYS board, LGC board
SYS board
LGC board 
SLG board
SYS board
SYS board 
SLG board, RADF
+5.1VB CN708Finisher
+12VA CN705 SYS board 
SYS board 
SYS board 
LGC board 
SLG board 
SYS board
-12VA
CN705
+12VB CN705
+12VB CN706
+12VB CN708...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE
8 - 1
8
8. REMOTE SERVICE
There are following functions as Remote Service. 
1) Auto Supply Order Automatically orders the toner by FAX or E-mail.
2) Service Notification Notifies the status of the equipment to the service  technician by E-mail or FAX.
8.1 Auto Supply Order 
8.1.1 Outline
Automatically orders the toner. 
1) Placing an Order
There are two ways to place an order. 
- FAXInstallation of the FAX board is required. 
If the...

e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICEJune 2004 © TOSHIBA TEC
8 - 2
8.1.2 Setting Item
To enable Auto Supply Order, the following settings 
are required.
Note: Note: 
When selecting E-mail to place an order, it is requ ired that sending and receiving E-mails are 
available. Confirm the details to the administrator .
1) Self-diagnosis (08) Setting As the default setting, the Auto Supply Order setti ng screen is not displayed on the touch panel.
To display it, switching the Valid/Invalid setting...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE
8 - 3
8
2) Touch Panel Setting Each item is set from the Auto Supply Order screen  on the touch panel.
Entering the password and customer information is r equired because the setting is made from the 
ADMIN screen. Setting it with the administrator is  a must.
- Basic setting [ADMIN] > [SERVICE] > [SUPPLY ORDER SETUP] > [ORDER  INFORMATION]
*1 HTTP has not been supported yet. 
*2 Even when “FAX” is selected, the order is not pl aced...

e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICEJune 2004 © TOSHIBA TEC
8 - 4
- Detailed setting for the order [ADMIN] > [SERVICE] > [SUPPLY ORDER SETUP] > [TONER  ORDERING]
*1 The order is placed when the number of replaceme nt reaches the number specified for the 
CONDITION.
- FAX number of this equipment (common information) [ADMIN] > [FAX] > [TERMINAL ID]
- E-mail information of this equipment (common inform ation)
[ADMIN] > [E-MAIL] 
*1 When sending an E-mail, validity of the address  is checked. If...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE
8 - 5
8
8.1.3 Setting procedure
(1) Start up the self-diagnosis setting mode 08-765,  and then change the setting value to “0”.
(2) Turn the power OFF, and then ON. 
(3) Press the [USER FUNCTIONS] button to enter the user  function screen.
(4) Press the [ADMIN] button.  When the Administrator Password has been set, ADMI NISTRATOR PASSWORD screen is 
displayed.
 Fig.8-1
(5) Press the [PASSWORD] button and the screen is sw itched to a...

e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICEJune 2004 © TOSHIBA TEC
8 - 6
(7) The SERVICE screen is displayed.
 Fig.8-3
(8) Press the [SUPPLY ORDER SETUP] button.
 Fig.8-4
(9) Press the [ORDER INFORMATION] button. 
(10) The ORDER INFORMATION screen is displayed.
 Fig.8-5