Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 57
6
(6) Click the [F/W Download] button.
 Fig.6-57
(7) Select the model name of the equipment to be upd ated from the drop-down menu and click the 
[OK] button.
 Fig.6-58   

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 58
(8) Click the [OFFLINE] button.
 Fig.6-59
(9) The connection status between the printer driver  installed in the PC and the equipment to be 
connected is displayed. Select the equipment to be  updated and click the [Activate FSMS] but-
ton.
 Fig.6-60
Remark:  The content of “Status” display can be renewed to t he latest status by clicking the [Refresh] but-
ton. When the status is displayed as “Disconnected”  because the...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 59
6
(10) Check the firmware to be updated and click the  [OK] button.
 Fig.6-61
Remark: 
The relation between the types of firmware to be up dated and items to check is as follows in the 
table below.
Item Firmware Data file name to update
Program System ROM sysfirm.tz 
UI Data uidataF.tz
Common UI Data uidata0.tz
1st Language UI Data uidata1.tz
MROM Engine ROM mfirm.tz
Scan ROM Scanner ROM scnfirm.tz
NIC ROM NIC ROM...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 60
(11) Select the data file to be updated and click th e [OK] button.
There are two data filing methods: Selecting the mu ltiple data files in a batch (select the folder 
where the files are saved) and selecting each data  file individually.
 Selecting the multiple data files in a batch - Select “Download File Folder”. 
- Click the [Browse] button and select the folder whe re the files are saved.
 Fig.6-62
 Selecting each...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 61
6
Remark:  When selecting the multiple files in a batch, the n ame of the unselected data file (not saved in the 
folder) may be displayed. In this case, click the [ OK] button and then the update of all files except 
the displayed file starts.
 Fig.6-64
(12) The selected data is transmitted to the equipme nt.
The data file name being transmitted and transmissi on condition are displayed at the bottom.
 Fig.6-65
Remark:...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 62
(14) The equipment restarts automatically and the ite ms to be updated and processing status are dis-
played on the LCD screen.
 Fig.6-67
04/09 

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 63
6
(15) “Update Completed!!” is displayed at the bottom  of the LCD screen after the updating is com-
pleted properly.
 Fig.6-68
“Update Failed!!” is displayed at the bottom of the  LCD screen when the updating is not com-
pleted properly. Turn OFF the power, and then check  the following items. After confirming and 
clearing the problems, restart updating from the be ginning.
 Are the equipment and PC properly connected?...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 64
*When the updating of the NIC firmware is failed, a n error message is displayed as the figure 
below. Turn OFF the power and then check the above- mentioned items. After confirming 
them, select only ”NIC ROM” (6. NIC Firmware Update ) and restart updating from the begin-
ning. This may complete the updating properly.
 Fig.6-70
If the updating of the NIC firmware is still failed , check the prescription corresponding to...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 65
6
(16) Turn OFF the power of the equipment. 
(17) Perform the initialization of the updating data  (NVRAM updating).
 Turn ON the power while [0] button and [8] button  are pressed simultaneously.
 Key in “947”, and then press the [START] button. 
 Press the [INITIALIZE] button.
[B] Confirmation of the updated data 
After the updating is completed, check each data ve rsion in the Setting Mode (08) to confirm that the...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 66
6.4 Firmware Updating with USB Storage Device 
(e-STUDIO200L/230/280)
In this equipment, it is feasible to update the fir mware by connecting the USB storage device on which  
the firmware data is written to the USB connector m ounted on the system control PC board and turning 
ON the power. 
The type of firmware to be updated can be selected  on the LCD screen in this method. This allows to 
update only the necessary...