Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 27
6

(1) Install the ROM to the download jig. Make sure the direction is correct (P.6-3 Fig.6-3) .
(2) Turn OFF the power of the equipment. 
(3) Take off the finisher rear cover.
 Fig.6-29
*Connect the finisher interface cable with the equi pment after removing the finisher rear cover.
(4) Connect the download jig with the jig connector o n the finisher control PC board.
 Fig.6-30
Finisher rear cover
Connector 

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 28
(5) Change the setting of he DIP switch on the finis her control PC board.
Change all the setting of the DIP switch (1-8) to O FF.
Note: Note: 
Record the current settings of the DIP switch befor e changing them. After the updating is com-
pleted, return the DIP switch to the status as reco rd.
 Fig.6-31
(6) Turn ON the power while [0] button and [8] butto n are pressed simultaneously.
Updating starts automatically and the...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 29
6

Important:   Before updating the FAX ROM, make sure to print ou t the current Function list for mainte-
nance, Function list (ADMIN), Phone book number inf ormation and Group number informa-
tion. In case the updating is failed and the regist ered information of the users is lost for some 
reason, re-register the user information referring  to the lists and recover it.
 Confirm the following items before turning OFF...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 30
(5) Turn ON the power while [0] button and [8] butto n are pressed simultaneously. Updating starts 
automatically and the LED on the download jig light s.
(6) After the update is completed properly, the LED  on the download jig blinks. The LED starts blink-
ing in approx. 30 sec. since the update starts. It i s assumed that the update is failed if it does not 
start blinking even though 1 min. has passed. In th is case,...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 31
6
6.2 Firmware Updating with Download Jig 
(e-STUDIO202L/232/282)
In this equipment, it is feasible to update the fir mware automatically by connecting the download jig 
using the dedicated connector and turning ON the eq uipment.
The download jig consists of the ROM, in which the  program is written, and the jig board.
And two types of the download jigs are available fo r each type of the firmware. 
For updating the...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 32
PWA-DWNLD-350-JIG2 (48MB)
 Fig.6-34 Jig board: PWA-DWNLD-350-JIG2 (48 MB)
Important:  The download jig (PWA-DWNLD-350-JIG) is the jig in  which the Flash ROM is mounted on the 
board directly. Therefore, ROM writer adapter (PWA- DL-ADP-350) is required to write the data to 
these Flash ROMs. Refer to the following to write t he data.
  P.6-42 6.2.2 Writing the data to the download jig  (PWA-DWNLD-350-JIG)
K-PWA-DLM-320...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 33
6
6.2.1 PWA-DWNLD-350-JIG2 (48 MB)
The firmware of the equipment except for the hard d isk and the option can be updated individually or in 
a batch by using PWA-DWNLD-350-JIG2 (48 MB). Update  the ROM data written on each board 
according to the need such as the case of replacing  the system control PC board, logic PC board or 
scanning section control PC board.  
The data to be overwritten by this update are as fol lows....

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 34
(4) Connect the download jig with the jig connector  (CN100) on the SYS board.
 Fig.6-37
(5) Turn ON the power while [8] button and [9] butto n are pressed simultaneously.
The screen for selecting the items to be updated is  displayed. “*” is displayed next to the items to 
be updated. (All items are selected in the default  settings.)
Connector
05/11 

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 35
6
(6) Select the item with the digital keys. “*” is displayed next to the selected item. Display  or delete the “*” by pressing the number of the 
item. All items are selected in the default setting s.
 Select all items to update the firmware of the equ ipment in a batch.
 Select items as follows to update it individually. 
 
Select “0. OS Update”, “1. UI Update”, and “2. Syst em Firmware”.
 
Select “3. Engine Firmware...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 36
(7) Press the [START] button. Updating starts and the processing status is display ed on the LCD screen.
(8) “Update Completed.” is displayed at the bottom o f the LCD screen after the updating is com-
pleted properly.
Status display during update Status display when upd ate is completed 
OS Update  ....... OS Update  ....... Completed 
UI Data Update  ....... UI Data Update  ....... Complet ed
SysFirm Update  ..........