Toshiba Estudio 230 Manual

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 121
5
5.3.3 Caution when Data overwrite kit (GP-1050/1060)  is installed 
When the Data overwrite kit (GP-1050/1060) is installed, follow the cautions below. 
  
Be sure to perform 08-1426 (forcible HDD data clear ing) before disposing of the HDD of the equipment. 
* When the scrambler board is installed, data in the  HDD are overwritten with encrypted data and 
erased. 
 
Before the SYS board is disposed, the following cod es...

e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 122
2) Usage The combination of the values of ID=05 and c5 is us ed to diagnose whether or not the HDD has a 
physical failure when HDD failure is suspected (servi ce call F100-180 or 120 occurred).
3) ID=05 and c5
Result Description Diagnosis
ID VALUE
05 0 Low possibility of physical failure HDD replacemen t 
is not required.
c5 0
05 From 1 to 999 Defective sector has been reassigned  and HDD is recovered. HDD replacement 
is...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 123
5
4) Description of each ID
ID Name Meaning
01 Read Error Rate This attribute is a measure of the  read error rate.
02 Throughput Performance This attribute is a measure  of the throughput performance.
03 Spin Up Time This attribute is a measure of how qu ickly the drive is able to 
spin up from a spun down condition.
04 Spin Start/Stop Count This attribute is a measure o f the total number of spin ups 
from a spun down...

e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 124 

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 1
6
6. FIRMWARE UPDATING
In this equipment, following firmware is written on  the ROM on each board.
When you want to update the firmware above or the e quipment becomes inoperative status due to 
some defectives of the firmware, updating the firmw are is available by the following actions.
 
 Updating with the download jig  P.6-2 6.1 Firmware Updating with Download Jig (e- STUDIO200L/230/280)
 Updating with PC connected...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 2
6.1 Firmware Updating with Download Jig 
(e-STUDIO200L/230/280)
In this equipment, it is feasible to update the fir mware automatically by connecting the download jig 
using the dedicated connector and turning ON the eq uipment.
The download jig consists of the ROM, in which the  program is written, and the jig board. And three 
types of the download jigs are available for each t ype of the firmware.
For updating the...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 3
6
Important:   The download jig (PWA-DWNLD-350-JIG) has two types  having different ROM capacity. 
ROM capacity for each jig is as follows. 
* “PWA-DWNLD-350-JIG2 (48 MB)” is substitutable for “ PWA-DWNLD-350-JIG1 (16 MB)”
 The download jig (PWA-DWNLD-350-JIG) is different  type jig. The Flash ROM is installed on 
the board directly. Therefore, ROM writer adapter ( PWA-DL-ADP-350) is required to write the 
data to these...

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 4
6.1.1 PWA-DWNLD-350-JIG2 (48 MB)
The master data written on the hard disk can be upd
ated by using PWA-DWNLD-350-JIG2 (48 MB). 
Update the master data according to the need such a s the case of replacing the hard disk.
The data to be overwritten are as follows. 
 HDD program data (RIP data, list data, Web data, f iling box control data)
 UI data (fixed section data, common section data,  the language 1 to 7 data, the...

June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATING
6 - 5
6
(4) Connect the download jig with the jig connector  (CN100) on the SYS board.
 Fig.6-5
(5) Turn ON the power.
Downloading starts automatically and the processing s tatus is displayed on LCD screen.
 Fig.6-6
Connector 

e-STUDIO200L/202L/230/232/280/282 FIRMWARE UPDATINGJune 2004 © TOSHIBA TEC
6 - 6
(6) “Update Completed!!” is displayed at the bottom  of the LCD screen after the updating is com-
pleted properly.
 Fig.6-7
“Update Failed.” is displayed at the bottom of the  LCD screen when the updating is not com-
pleted properly. Turn OFF the power, and then check  the following items. After confirming and 
clearing the problems, restart updating from the be ginning.
 Is the download jig connected properly? 
 Is the...