Toshiba Estudio 230 Manual
Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 501
![Page 501
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 71
5
[CC90] Upper stack tray lift motor abnormality
MJ-1022
Is the wiring between the finisher controller PC bo ard and upper stack tray lift motor (M5)
correct?
NO
Correct the wiring.
YES
Are the front and rear sides of the upper stack tra y leveled?
NO
Level them.
YES
Is the upper stack tray lift motor clock sensor (S19 ) working properly?
NO
Replace the sensor.
YES
Is the stack tray paper height sensor (S10) working...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-500.png "Page 501
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 71
5
[CC90] Upper stack tray lift motor abnormality
MJ-1022
Is the wiring between the finisher controller PC bo ard and upper stack tray lift motor (M5)
correct?
NO
Correct the wiring.
YES
Are the front and rear sides of the upper stack tra y leveled?
NO
Level them.
YES
Is the upper stack tray lift motor clock sensor (S19 ) working properly?
NO
Replace the sensor.
YES
Is the stack tray paper height sensor (S10) working...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 71 5 [CC90] Upper stack tray lift motor abnormality MJ-1022 Is the wiring between the finisher controller PC bo ard and upper stack tray lift motor (M5) correct? NO Correct the wiring. YES Are the front and rear sides of the upper stack tra y leveled? NO Level them. YES Is the upper stack tray lift motor clock sensor (S19 ) working properly? NO Replace the sensor. YES Is the stack tray paper height sensor (S10) working...
Page 502
![Page 502
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 72
[CCA0] Lower stack tray lift motor abnormality
MJ-1022
Is the wiring between the finisher controller PC bo ard and lower stack tray lift motor (M7)
correct?
NO
Correct the wiring.
YES
Are the front and rear sides of the lower stack tra y leveled?
NO
Level them.
YES
Is the lower stack tray lift motor clock sensor (S9) working properly?
NO
Replace the sensor.
YES
Is the stack tray paper height sensor (S10) working...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-501.png "Page 502
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 72
[CCA0] Lower stack tray lift motor abnormality
MJ-1022
Is the wiring between the finisher controller PC bo ard and lower stack tray lift motor (M7)
correct?
NO
Correct the wiring.
YES
Are the front and rear sides of the lower stack tra y leveled?
NO
Level them.
YES
Is the lower stack tray lift motor clock sensor (S9) working properly?
NO
Replace the sensor.
YES
Is the stack tray paper height sensor (S10) working...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 72 [CCA0] Lower stack tray lift motor abnormality MJ-1022 Is the wiring between the finisher controller PC bo ard and lower stack tray lift motor (M7) correct? NO Correct the wiring. YES Are the front and rear sides of the lower stack tra y leveled? NO Level them. YES Is the lower stack tray lift motor clock sensor (S9) working properly? NO Replace the sensor. YES Is the stack tray paper height sensor (S10) working...
Page 503
![Page 503
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 73
5
[CCB0] Rear jogging plate motor abnormality/Alignmen t motor (rear) abnormality
MJ-1022 (Rear jogging plate motor abnormality)
Is the rear jogging plate home position sensor (S7) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and rear jogging motor (M4) correct?
NO
Correct the wiring.
YES
Has the rack run over the stopper of the roll?
YES
Fix it.
NO
1)...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-502.png "Page 503
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 73
5
[CCB0] Rear jogging plate motor abnormality/Alignmen t motor (rear) abnormality
MJ-1022 (Rear jogging plate motor abnormality)
Is the rear jogging plate home position sensor (S7) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and rear jogging motor (M4) correct?
NO
Correct the wiring.
YES
Has the rack run over the stopper of the roll?
YES
Fix it.
NO
1)...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 73 5 [CCB0] Rear jogging plate motor abnormality/Alignmen t motor (rear) abnormality MJ-1022 (Rear jogging plate motor abnormality) Is the rear jogging plate home position sensor (S7) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC bo ard and rear jogging motor (M4) correct? NO Correct the wiring. YES Has the rack run over the stopper of the roll? YES Fix it. NO 1)...
Page 504
![Page 504
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 74
[CDC0] Punch power failure occurred abnormality MJ-1025
Is the problem solved by turning the power of the e quipment OFF and ON?
YES
End
NO
Is the wiring between the finisher controller PC bo ard and punch controller PC board cor-
rect?
NO
Correct the wiring.
YES
Does the voltage between the CN14-5 (+) and CN14-3 (-) on the finisher controller PC
board become 24 V?
YES
Replace the punch controller PC board.
NO...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-503.png "Page 504
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 74
[CDC0] Punch power failure occurred abnormality MJ-1025
Is the problem solved by turning the power of the e quipment OFF and ON?
YES
End
NO
Is the wiring between the finisher controller PC bo ard and punch controller PC board cor-
rect?
NO
Correct the wiring.
YES
Does the voltage between the CN14-5 (+) and CN14-3 (-) on the finisher controller PC
board become 24 V?
YES
Replace the punch controller PC board.
NO...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 74 [CDC0] Punch power failure occurred abnormality MJ-1025 Is the problem solved by turning the power of the e quipment OFF and ON? YES End NO Is the wiring between the finisher controller PC bo ard and punch controller PC board cor- rect? NO Correct the wiring. YES Does the voltage between the CN14-5 (+) and CN14-3 (-) on the finisher controller PC board become 24 V? YES Replace the punch controller PC board. NO...
Page 505
![Page 505
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 75
5
[CDE0] Paddle motor abnormality
MJ-1025
Is the paddle home position sensor (PI2) working pr operly?
NO
Replace the sensor.
YES
Is the Swing guide home position sensor (PI3) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and Paddle motor (M2) correct?
NO
Correct the wiring.
YES
Try to rotate the paddle motor (M2) clockwise and c ounterclockwise by hand. Is there...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-504.png "Page 505
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 75
5
[CDE0] Paddle motor abnormality
MJ-1025
Is the paddle home position sensor (PI2) working pr operly?
NO
Replace the sensor.
YES
Is the Swing guide home position sensor (PI3) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and Paddle motor (M2) correct?
NO
Correct the wiring.
YES
Try to rotate the paddle motor (M2) clockwise and c ounterclockwise by hand. Is there...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 75 5 [CDE0] Paddle motor abnormality MJ-1025 Is the paddle home position sensor (PI2) working pr operly? NO Replace the sensor. YES Is the Swing guide home position sensor (PI3) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC bo ard and Paddle motor (M2) correct? NO Correct the wiring. YES Try to rotate the paddle motor (M2) clockwise and c ounterclockwise by hand. Is there...
Page 506
![Page 506
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 76
5.1.15 Service call for others
[C970] High-voltage transformer abnormality
(1) Is the main charger installed securely?
(2) Check if the spring of high-voltage supply conta ct point is deformed.
(3) Check if the needle electrode is broken or the m ain charger grid is deformed.
(4) Check if any foreign matters is on the needle el ectrode or the main charger grid.
(5) Is the transfer/separation charger installed sec urely?
(6)...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-505.png "Page 506
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 76
5.1.15 Service call for others
[C970] High-voltage transformer abnormality
(1) Is the main charger installed securely?
(2) Check if the spring of high-voltage supply conta ct point is deformed.
(3) Check if the needle electrode is broken or the m ain charger grid is deformed.
(4) Check if any foreign matters is on the needle el ectrode or the main charger grid.
(5) Is the transfer/separation charger installed sec urely?
(6)...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 76 5.1.15 Service call for others [C970] High-voltage transformer abnormality (1) Is the main charger installed securely? (2) Check if the spring of high-voltage supply conta ct point is deformed. (3) Check if the needle electrode is broken or the m ain charger grid is deformed. (4) Check if any foreign matters is on the needle el ectrode or the main charger grid. (5) Is the transfer/separation charger installed sec urely? (6)...
Page 507
![Page 507
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 77
5
[F091] NVRAM abnormality on the SYS board
(1) Turn the power OFF and start up the Setting Mode (08).
(2) When the message “NVRAM ERROR DOES IT INITIALIZE ?” is displayed on the LCD, press the
[INTERRUPT] or [INITIALIZE] button. (NVRAM is initi alized.)
(3) Perform the panel calibration (08-692).
Note: Note: When the NVRAM is initialized, the scanner and imag e processing related adjustments are
also initialized....](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-506.png "Page 507
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 77
5
[F091] NVRAM abnormality on the SYS board
(1) Turn the power OFF and start up the Setting Mode (08).
(2) When the message “NVRAM ERROR DOES IT INITIALIZE ?” is displayed on the LCD, press the
[INTERRUPT] or [INITIALIZE] button. (NVRAM is initi alized.)
(3) Perform the panel calibration (08-692).
Note: Note: When the NVRAM is initialized, the scanner and imag e processing related adjustments are
also initialized....")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 77 5 [F091] NVRAM abnormality on the SYS board (1) Turn the power OFF and start up the Setting Mode (08). (2) When the message “NVRAM ERROR DOES IT INITIALIZE ?” is displayed on the LCD, press the [INTERRUPT] or [INITIALIZE] button. (NVRAM is initi alized.) (3) Perform the panel calibration (08-692). Note: Note: When the NVRAM is initialized, the scanner and imag e processing related adjustments are also initialized....
Page 508
![Page 508
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 78
[F106] Point and Print partition damage
(1) Turn the power OFF and start up the Setting Mode (08).
(2) Key in “662” and press the [START] button. (Part ition clearing is performed.)
(3) Restart the equipment.
(4) Access TopAccess. Click the [Administration] tab , and then click the Maintenance Menu to open.
Then install the “Point and Print” driver.
[F107] /SHR partition damage
Initialize the Electronic Filing using the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-507.png "Page 508
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 78
[F106] Point and Print partition damage
(1) Turn the power OFF and start up the Setting Mode (08).
(2) Key in “662” and press the [START] button. (Part ition clearing is performed.)
(3) Restart the equipment.
(4) Access TopAccess. Click the [Administration] tab , and then click the Maintenance Menu to open.
Then install the “Point and Print” driver.
[F107] /SHR partition damage
Initialize the Electronic Filing using the...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 78 [F106] Point and Print partition damage (1) Turn the power OFF and start up the Setting Mode (08). (2) Key in “662” and press the [START] button. (Part ition clearing is performed.) (3) Restart the equipment. (4) Access TopAccess. Click the [Administration] tab , and then click the Maintenance Menu to open. Then install the “Point and Print” driver. [F107] /SHR partition damage Initialize the Electronic Filing using the...
Page 509
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 79 5 5.1.16 Error in Internet FAX / Scanning Function Notes: 1. When initializing the Electronic Filing (Setting Mo de (08-666)), all data in the Electronic Filing are erased. Back up the data in the Electron ic Filing by using the Electronic Fil- ing Function of TopAccess before the initialization . 2. When initializing the shared folder (Setting Mode ( 08-667)), all data in the shared folder are erased. Back up the data in...
Page 510
![Page 510
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 80
[1C30] Directory creation failure
[1C31] File creation failure
[1C33] File access failure
Check if the access privilege to the storage direct ory is writable.
Check if the server or local disk has a sufficient space in disk capacity.
[1C40] Image conversion abnormality
Turn the power OFF and then back ON. Perform the jo b in error again.
Replace the main memory and perform the job again.
[1C60] HDD full failure during...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-509.png "Page 510
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 80
[1C30] Directory creation failure
[1C31] File creation failure
[1C33] File access failure
Check if the access privilege to the storage direct ory is writable.
Check if the server or local disk has a sufficient space in disk capacity.
[1C40] Image conversion abnormality
Turn the power OFF and then back ON. Perform the jo b in error again.
Replace the main memory and perform the job again.
[1C60] HDD full failure during...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 80 [1C30] Directory creation failure [1C31] File creation failure [1C33] File access failure Check if the access privilege to the storage direct ory is writable. Check if the server or local disk has a sufficient space in disk capacity. [1C40] Image conversion abnormality Turn the power OFF and then back ON. Perform the jo b in error again. Replace the main memory and perform the job again. [1C60] HDD full failure during...