Toshiba Estudio 230 Manual
Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 451
![Page 451
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 21
5
[E190] LCF misfeeding (paper not reaching the LCF fe ed sensor)
Open the LCF side cover. Is there any paper in fron t of the LCF feed sensor?
YES
Remove the paper.
NO
Is the LCF feed sensor working?
(Perform the input check in the test mode: 03-[FAX] OFF/[5]/[G])
l l ll l ll l ll l
NO
1) Check if the connector of the LCF feed sensor is d isconnected.
2) Check if either of the connectors CN100 or CN104 on the LCF board...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-450.png "Page 451
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 21
5
[E190] LCF misfeeding (paper not reaching the LCF fe ed sensor)
Open the LCF side cover. Is there any paper in fron t of the LCF feed sensor?
YES
Remove the paper.
NO
Is the LCF feed sensor working?
(Perform the input check in the test mode: 03-[FAX] OFF/[5]/[G])
l l ll l ll l ll l
NO
1) Check if the connector of the LCF feed sensor is d isconnected.
2) Check if either of the connectors CN100 or CN104 on the LCF board...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 21 5 [E190] LCF misfeeding (paper not reaching the LCF fe ed sensor) Open the LCF side cover. Is there any paper in fron t of the LCF feed sensor? YES Remove the paper. NO Is the LCF feed sensor working? (Perform the input check in the test mode: 03-[FAX] OFF/[5]/[G]) l l ll l ll l ll l NO 1) Check if the connector of the LCF feed sensor is d isconnected. 2) Check if either of the connectors CN100 or CN104 on the LCF board...
Page 452
![Page 452
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 22
5.1.3 Cover open jam
[E400] Transfer cover opened during printing
Is the transfer cover open?
YES
Remove paper if there is any, then close the cover.
NO
Is the transfer cover opening/closing switch workin g?
(Perform the input check in the test mode: 03-[FAX] ON/[2]/[G])
l ll l ll l ll
NO
1) Check if the connector of the transfer cover open ing/closing switch is
disconnected.
2) Check if the connector CN305 on the LGC...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-451.png "Page 452
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 22
5.1.3 Cover open jam
[E400] Transfer cover opened during printing
Is the transfer cover open?
YES
Remove paper if there is any, then close the cover.
NO
Is the transfer cover opening/closing switch workin g?
(Perform the input check in the test mode: 03-[FAX] ON/[2]/[G])
l ll l ll l ll
NO
1) Check if the connector of the transfer cover open ing/closing switch is
disconnected.
2) Check if the connector CN305 on the LGC...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 22 5.1.3 Cover open jam [E400] Transfer cover opened during printing Is the transfer cover open? YES Remove paper if there is any, then close the cover. NO Is the transfer cover opening/closing switch workin g? (Perform the input check in the test mode: 03-[FAX] ON/[2]/[G]) l ll l ll l ll NO 1) Check if the connector of the transfer cover open ing/closing switch is disconnected. 2) Check if the connector CN305 on the LGC...
Page 453
![Page 453
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 23
5
[E410] Front cover opened during printing
Is the front cover open?
YES
Close the cover.
NO
Is the front cover opening/closing switch working?
(Perform the input check in the test mode: 03-[FAX] ON/[2]/[D])
l ll l ll l ll
NO
1) Check if the connector of the front cover opening /closing switch is
disconnected.
2) Check if the connector CN303 on the LGC board is disconnected.
3) Check if the connector pins are...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-452.png "Page 453
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 23
5
[E410] Front cover opened during printing
Is the front cover open?
YES
Close the cover.
NO
Is the front cover opening/closing switch working?
(Perform the input check in the test mode: 03-[FAX] ON/[2]/[D])
l ll l ll l ll
NO
1) Check if the connector of the front cover opening /closing switch is
disconnected.
2) Check if the connector CN303 on the LGC board is disconnected.
3) Check if the connector pins are...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 23 5 [E410] Front cover opened during printing Is the front cover open? YES Close the cover. NO Is the front cover opening/closing switch working? (Perform the input check in the test mode: 03-[FAX] ON/[2]/[D]) l ll l ll l ll NO 1) Check if the connector of the front cover opening /closing switch is disconnected. 2) Check if the connector CN303 on the LGC board is disconnected. 3) Check if the connector pins are...
Page 454
![Page 454
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 24
[E420] PFP side cover opened during printing
Is the PFP side cover open?
YES
Remove the paper if there is any, then close the co ver.
NO
Is the PFP side cover opening/closing switch workin g?
(Perform the input check in the test mode: 03-[FAX]OFF/[2]/[F])
l l ll l ll l ll l l
NO
1) Check if the connector of the PFP side cover open ing/closing switch
is disconnected.
2) Check if either of the connectors CN241 or CN243 o...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-453.png "Page 454
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 24
[E420] PFP side cover opened during printing
Is the PFP side cover open?
YES
Remove the paper if there is any, then close the co ver.
NO
Is the PFP side cover opening/closing switch workin g?
(Perform the input check in the test mode: 03-[FAX]OFF/[2]/[F])
l l ll l ll l ll l l
NO
1) Check if the connector of the PFP side cover open ing/closing switch
is disconnected.
2) Check if either of the connectors CN241 or CN243 o...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 24 [E420] PFP side cover opened during printing Is the PFP side cover open? YES Remove the paper if there is any, then close the co ver. NO Is the PFP side cover opening/closing switch workin g? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[F]) l l ll l ll l ll l l NO 1) Check if the connector of the PFP side cover open ing/closing switch is disconnected. 2) Check if either of the connectors CN241 or CN243 o...
Page 455
![Page 455
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 25
5
[E430] ADU opened during printing
Is the ADU open?
YES
Remove the paper if there is any, then close the AD U.
NO
Is the ADU opening/closing switch working?
(Perform the input check in the test mode: 03-[FAX] OFF/[1]/[F])
l l ll l ll l ll l l
NO
1) Check if the connector of the ADU opening/closing switch is discon-
nected.
2) Check if either of the connectors CN562 or CN217 on the ADU board
is disconnected.
3) Check...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-454.png "Page 455
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 25
5
[E430] ADU opened during printing
Is the ADU open?
YES
Remove the paper if there is any, then close the AD U.
NO
Is the ADU opening/closing switch working?
(Perform the input check in the test mode: 03-[FAX] OFF/[1]/[F])
l l ll l ll l ll l l
NO
1) Check if the connector of the ADU opening/closing switch is discon-
nected.
2) Check if either of the connectors CN562 or CN217 on the ADU board
is disconnected.
3) Check...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 25 5 [E430] ADU opened during printing Is the ADU open? YES Remove the paper if there is any, then close the AD U. NO Is the ADU opening/closing switch working? (Perform the input check in the test mode: 03-[FAX] OFF/[1]/[F]) l l ll l ll l ll l l NO 1) Check if the connector of the ADU opening/closing switch is discon- nected. 2) Check if either of the connectors CN562 or CN217 on the ADU board is disconnected. 3) Check...
Page 456
![Page 456
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 26
[E450] LCF side cover opened during printing
Is the LCF side cover open?
YES
Remove the paper if there is any, then close the co ver.
NO
Is the LCF side cover opening/closing switch workin g?
(Perform the input check in the test mode: 03-[FAX]OFF/[5]/[D])
l l ll l ll l ll l l
NO
1) Check if the connector of the LCF side cover open ing/closing switch
is disconnected.
2) Check if either of the connectors CN100 or CN106...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-455.png "Page 456
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 26
[E450] LCF side cover opened during printing
Is the LCF side cover open?
YES
Remove the paper if there is any, then close the co ver.
NO
Is the LCF side cover opening/closing switch workin g?
(Perform the input check in the test mode: 03-[FAX]OFF/[5]/[D])
l l ll l ll l ll l l
NO
1) Check if the connector of the LCF side cover open ing/closing switch
is disconnected.
2) Check if either of the connectors CN100 or CN106...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 26 [E450] LCF side cover opened during printing Is the LCF side cover open? YES Remove the paper if there is any, then close the co ver. NO Is the LCF side cover opening/closing switch workin g? (Perform the input check in the test mode: 03-[FAX]OFF/[5]/[D]) l l ll l ll l ll l l NO 1) Check if the connector of the LCF side cover open ing/closing switch is disconnected. 2) Check if either of the connectors CN100 or CN106...
Page 457
![Page 457
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 27
5
[E490] JSP cover opened during printing
Is the JSP cover open?
YES
Remove the paper if there is any, then close the co ver.
NO
Is the JSP cover switch working?
(Perform the input check in the test mode: 03-[FAX] ON/[3]/[F])
l l ll l ll l ll l
NO
1) Check if the connector of the JSP cover switch is disconnected.
2) Check if either of the connectors CN260 or CN261 on the JSP board
is disconnected.
3) Check if the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-456.png "Page 457
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 27
5
[E490] JSP cover opened during printing
Is the JSP cover open?
YES
Remove the paper if there is any, then close the co ver.
NO
Is the JSP cover switch working?
(Perform the input check in the test mode: 03-[FAX] ON/[3]/[F])
l l ll l ll l ll l
NO
1) Check if the connector of the JSP cover switch is disconnected.
2) Check if either of the connectors CN260 or CN261 on the JSP board
is disconnected.
3) Check if the...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 27 5 [E490] JSP cover opened during printing Is the JSP cover open? YES Remove the paper if there is any, then close the co ver. NO Is the JSP cover switch working? (Perform the input check in the test mode: 03-[FAX] ON/[3]/[F]) l l ll l ll l ll l NO 1) Check if the connector of the JSP cover switch is disconnected. 2) Check if either of the connectors CN260 or CN261 on the JSP board is disconnected. 3) Check if the...
Page 458
![Page 458
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 28
5.1.4 Transport jam (RADF)
Note: Note:
When performing the RADF related troubleshooting, b e sure to perform “Automatic
adjustment of RADF sensor and EEPROM initialization (05-356)” and “RADF original
guide width adjustment (05-367/368)” consecutively at the Adjustment Mode whenever the
RADF board, original length sensor, read sensor or reverse sensor has been replaced.
[E711] Jam not reaching the original length...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-457.png "Page 458
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 28
5.1.4 Transport jam (RADF)
Note: Note:
When performing the RADF related troubleshooting, b e sure to perform “Automatic
adjustment of RADF sensor and EEPROM initialization (05-356)” and “RADF original
guide width adjustment (05-367/368)” consecutively at the Adjustment Mode whenever the
RADF board, original length sensor, read sensor or reverse sensor has been replaced.
[E711] Jam not reaching the original length...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 28 5.1.4 Transport jam (RADF) Note: Note: When performing the RADF related troubleshooting, b e sure to perform “Automatic adjustment of RADF sensor and EEPROM initialization (05-356)” and “RADF original guide width adjustment (05-367/368)” consecutively at the Adjustment Mode whenever the RADF board, original length sensor, read sensor or reverse sensor has been replaced. [E711] Jam not reaching the original length...
Page 459
![Page 459
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 29
5
[E714] Feed signal reception jam
Is the empty sensor working? (Perform the input che ck: 03-[FAX]ON/[7]/[B])
l l ll l l l ll
NO
1) Check if the lever of empty sensor is working nor mally.
2) Check if the connector of the empty sensor is dis connected.
3) Check if the connector CN5 on the RADF board is d isconnected.
4) Check if the connector pins are disconnected or t he harnesses are
open circuited.
5) Check if the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-458.png "Page 459
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 29
5
[E714] Feed signal reception jam
Is the empty sensor working? (Perform the input che ck: 03-[FAX]ON/[7]/[B])
l l ll l l l ll
NO
1) Check if the lever of empty sensor is working nor mally.
2) Check if the connector of the empty sensor is dis connected.
3) Check if the connector CN5 on the RADF board is d isconnected.
4) Check if the connector pins are disconnected or t he harnesses are
open circuited.
5) Check if the...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 29 5 [E714] Feed signal reception jam Is the empty sensor working? (Perform the input che ck: 03-[FAX]ON/[7]/[B]) l l ll l l l ll NO 1) Check if the lever of empty sensor is working nor mally. 2) Check if the connector of the empty sensor is dis connected. 3) Check if the connector CN5 on the RADF board is d isconnected. 4) Check if the connector pins are disconnected or t he harnesses are open circuited. 5) Check if the...
Page 460
![Page 460
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 30
[E722] Jam not reaching the exit sensor (during scan ning)
[E723] Jam not reaching the reverse sensor (during s canning)
Is the read roller stained?
YES
Clean the roller.
NO
Are the exit sensor and reverse sensor working?
(Perform the input check: 03-[FAX]ON/[7]/[E], /[7]/ [F])
l l l ll l ll l
NO
1) Check if the connectors of the exit sensor and reve rse sensor are
disconnected.
2) Check if the connector CN4 on the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-459.png "Page 460
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 30
[E722] Jam not reaching the exit sensor (during scan ning)
[E723] Jam not reaching the reverse sensor (during s canning)
Is the read roller stained?
YES
Clean the roller.
NO
Are the exit sensor and reverse sensor working?
(Perform the input check: 03-[FAX]ON/[7]/[E], /[7]/ [F])
l l l ll l ll l
NO
1) Check if the connectors of the exit sensor and reve rse sensor are
disconnected.
2) Check if the connector CN4 on the...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 30 [E722] Jam not reaching the exit sensor (during scan ning) [E723] Jam not reaching the reverse sensor (during s canning) Is the read roller stained? YES Clean the roller. NO Are the exit sensor and reverse sensor working? (Perform the input check: 03-[FAX]ON/[7]/[E], /[7]/ [F]) l l l ll l ll l NO 1) Check if the connectors of the exit sensor and reve rse sensor are disconnected. 2) Check if the connector CN4 on the...