Toshiba Estudio 230 Manual
Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 491
![Page 491
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 61
5
5.1.14 Finisher related service call
[CB10] Transport motor abnormality
MJ-1025
Is the stack feed roller (upper) home position senso r (PI12) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and feed motor (M1) correct?
NO
Correct the wiring.
YES
Try turning the stack feed roller (upper) shaft by hand. Does the stack feed roller (upper)
move up/down normally?
NO...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-490.png "Page 491
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 61
5
5.1.14 Finisher related service call
[CB10] Transport motor abnormality
MJ-1025
Is the stack feed roller (upper) home position senso r (PI12) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and feed motor (M1) correct?
NO
Correct the wiring.
YES
Try turning the stack feed roller (upper) shaft by hand. Does the stack feed roller (upper)
move up/down normally?
NO...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 61 5 5.1.14 Finisher related service call [CB10] Transport motor abnormality MJ-1025 Is the stack feed roller (upper) home position senso r (PI12) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC bo ard and feed motor (M1) correct? NO Correct the wiring. YES Try turning the stack feed roller (upper) shaft by hand. Does the stack feed roller (upper) move up/down normally? NO...
Page 492
![Page 492
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 62
[CB20] Delivery motor abnormality
MJ-1022
Rotate the delivery roller by hand. Does it rotate smoothly?
NO
Fix the mechanism.
YES
Is the wiring between the finisher controller PC bo ard and delivery motor (M1) correct?
NO
Correct the wiring.
YES
Is the delivery motor clock sensor (S1) working prop erly?
NO
Replace the sensor.
YES
1) Replace the delivery motor (M1).
2) Replace the finisher controller PC board....](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-491.png "Page 492
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 62
[CB20] Delivery motor abnormality
MJ-1022
Rotate the delivery roller by hand. Does it rotate smoothly?
NO
Fix the mechanism.
YES
Is the wiring between the finisher controller PC bo ard and delivery motor (M1) correct?
NO
Correct the wiring.
YES
Is the delivery motor clock sensor (S1) working prop erly?
NO
Replace the sensor.
YES
1) Replace the delivery motor (M1).
2) Replace the finisher controller PC board....")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 62 [CB20] Delivery motor abnormality MJ-1022 Rotate the delivery roller by hand. Does it rotate smoothly? NO Fix the mechanism. YES Is the wiring between the finisher controller PC bo ard and delivery motor (M1) correct? NO Correct the wiring. YES Is the delivery motor clock sensor (S1) working prop erly? NO Replace the sensor. YES 1) Replace the delivery motor (M1). 2) Replace the finisher controller PC board....
Page 493
![Page 493
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 63
5
[CB30] Tray lift motor abnormality
MJ-1025
[Procedure 1]
Is the paper surface sensor (PI9) working properly?
NO
Replace the sensor.
YES
Is the tray up/down mechanism working properly?
NO
Fix the mechanism.
YES
Is 24 VDC supplied from the finisher controller PC board to the shift motor as soon as the
tray is driven?
NO
Replace the finisher controller PC board.
YES
Is the wiring between the finisher controller PC...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-492.png "Page 493
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 63
5
[CB30] Tray lift motor abnormality
MJ-1025
[Procedure 1]
Is the paper surface sensor (PI9) working properly?
NO
Replace the sensor.
YES
Is the tray up/down mechanism working properly?
NO
Fix the mechanism.
YES
Is 24 VDC supplied from the finisher controller PC board to the shift motor as soon as the
tray is driven?
NO
Replace the finisher controller PC board.
YES
Is the wiring between the finisher controller PC...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 63 5 [CB30] Tray lift motor abnormality MJ-1025 [Procedure 1] Is the paper surface sensor (PI9) working properly? NO Replace the sensor. YES Is the tray up/down mechanism working properly? NO Fix the mechanism. YES Is 24 VDC supplied from the finisher controller PC board to the shift motor as soon as the tray is driven? NO Replace the finisher controller PC board. YES Is the wiring between the finisher controller PC...
Page 494
![Page 494
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 64
[Procedure 3]
Does the tray go up?
l ll l l l ll l ll l
YES NO
Is 24 VDC supplied from the finisher controller PCB to the shift motor as
soon as the tray is driven?
NO
Replace the finisher controller PC board.
YES
Is there any problem with the tray up/down mechanism ?
YES
Fix the lift mechanism.
NO
Replace the shift motor.
Is the shift motor clock sensor (PI7) working prope rly?
YES
Replace the finisher...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-493.png "Page 494
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 64
[Procedure 3]
Does the tray go up?
l ll l l l ll l ll l
YES NO
Is 24 VDC supplied from the finisher controller PCB to the shift motor as
soon as the tray is driven?
NO
Replace the finisher controller PC board.
YES
Is there any problem with the tray up/down mechanism ?
YES
Fix the lift mechanism.
NO
Replace the shift motor.
Is the shift motor clock sensor (PI7) working prope rly?
YES
Replace the finisher...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 64 [Procedure 3] Does the tray go up? l ll l l l ll l ll l YES NO Is 24 VDC supplied from the finisher controller PCB to the shift motor as soon as the tray is driven? NO Replace the finisher controller PC board. YES Is there any problem with the tray up/down mechanism ? YES Fix the lift mechanism. NO Replace the shift motor. Is the shift motor clock sensor (PI7) working prope rly? YES Replace the finisher...
Page 495
![Page 495
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 65
5
[Procedure 2]
Is the staple/fold motor clock sensor (PI14) workin g properly?
NO
Replace the sensor.
YES
Does the staple/fold motor operate at the appropria te timing?
YES
Replace the finisher controller PC board.
NO
Is the stapler unit drive mechanism working properl y?
NO
Fix the mechanism.
YES
Try replacing the staple/fold motor (M7). Is the pr oblem corrected?
YES
End.
NO
Replace the finisher controller PC...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-494.png "Page 495
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 65
5
[Procedure 2]
Is the staple/fold motor clock sensor (PI14) workin g properly?
NO
Replace the sensor.
YES
Does the staple/fold motor operate at the appropria te timing?
YES
Replace the finisher controller PC board.
NO
Is the stapler unit drive mechanism working properl y?
NO
Fix the mechanism.
YES
Try replacing the staple/fold motor (M7). Is the pr oblem corrected?
YES
End.
NO
Replace the finisher controller PC...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 65 5 [Procedure 2] Is the staple/fold motor clock sensor (PI14) workin g properly? NO Replace the sensor. YES Does the staple/fold motor operate at the appropria te timing? YES Replace the finisher controller PC board. NO Is the stapler unit drive mechanism working properl y? NO Fix the mechanism. YES Try replacing the staple/fold motor (M7). Is the pr oblem corrected? YES End. NO Replace the finisher controller PC...
Page 496
![Page 496
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 66
[Procedure 4]
Is the staple/fold motor clock sensor (PI14) workin g properly?
NO
Replace the sensor.
YES
Does the staple/fold motor operate at the appropria te timing?
YES
Replace the finisher controller PC board.
NO
Is the saddle stitch unit drive mechanism working p roperly?
NO
Fix the mechanism.
YES
Try replacing the staple/fold motor (M7). Is the pr oblem corrected?
YES
End.
NO
Replace the finisher controller...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-495.png "Page 496
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 66
[Procedure 4]
Is the staple/fold motor clock sensor (PI14) workin g properly?
NO
Replace the sensor.
YES
Does the staple/fold motor operate at the appropria te timing?
YES
Replace the finisher controller PC board.
NO
Is the saddle stitch unit drive mechanism working p roperly?
NO
Fix the mechanism.
YES
Try replacing the staple/fold motor (M7). Is the pr oblem corrected?
YES
End.
NO
Replace the finisher controller...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 66 [Procedure 4] Is the staple/fold motor clock sensor (PI14) workin g properly? NO Replace the sensor. YES Does the staple/fold motor operate at the appropria te timing? YES Replace the finisher controller PC board. NO Is the saddle stitch unit drive mechanism working p roperly? NO Fix the mechanism. YES Try replacing the staple/fold motor (M7). Is the pr oblem corrected? YES End. NO Replace the finisher controller...
Page 497
![Page 497
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 67
5
[CB80] Backup RAM data abnormality
MJ-1025
Is the problem solved by turning the power of the e quipment OFF and ON?
YES
End.
NO
1) Replace the finisher controller PC board.
2) Replace the punch controller PC board.
[CC30] Stack processing motor abnormality/Paddle mot or abnormality
MJ-1022 (Stack processing motor abnormality)
[Procedure 1]
Is the tension of the drive belt normal?
NO
Loosen the adjustment screw to...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-496.png "Page 497
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 67
5
[CB80] Backup RAM data abnormality
MJ-1025
Is the problem solved by turning the power of the e quipment OFF and ON?
YES
End.
NO
1) Replace the finisher controller PC board.
2) Replace the punch controller PC board.
[CC30] Stack processing motor abnormality/Paddle mot or abnormality
MJ-1022 (Stack processing motor abnormality)
[Procedure 1]
Is the tension of the drive belt normal?
NO
Loosen the adjustment screw to...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 67 5 [CB80] Backup RAM data abnormality MJ-1025 Is the problem solved by turning the power of the e quipment OFF and ON? YES End. NO 1) Replace the finisher controller PC board. 2) Replace the punch controller PC board. [CC30] Stack processing motor abnormality/Paddle mot or abnormality MJ-1022 (Stack processing motor abnormality) [Procedure 1] Is the tension of the drive belt normal? NO Loosen the adjustment screw to...
Page 498
![Page 498
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 68
[Procedure 2]
Does the bushing attached to the returning roller s haft smoothly move up and down?
l
NO
Apply grease on the cut-out part of the front side frame where the bush-
ing contacts.
YES
Is the spring of the returning roller detached?
YES
Attach the spring.
NO
Is the tension of the stack processing motor drive belt normal?
NO
Loosen the adjustment screw to adjust its tension.
YES
Is the returning roller...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-497.png "Page 498
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 68
[Procedure 2]
Does the bushing attached to the returning roller s haft smoothly move up and down?
l
NO
Apply grease on the cut-out part of the front side frame where the bush-
ing contacts.
YES
Is the spring of the returning roller detached?
YES
Attach the spring.
NO
Is the tension of the stack processing motor drive belt normal?
NO
Loosen the adjustment screw to adjust its tension.
YES
Is the returning roller...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 68 [Procedure 2] Does the bushing attached to the returning roller s haft smoothly move up and down? l NO Apply grease on the cut-out part of the front side frame where the bush- ing contacts. YES Is the spring of the returning roller detached? YES Attach the spring. NO Is the tension of the stack processing motor drive belt normal? NO Loosen the adjustment screw to adjust its tension. YES Is the returning roller...
Page 499
![Page 499
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 69
5
[CC50] Horizontal registration motor abnormality MJ-1025
Is the horizontal registration home position sensor (PI2P) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and the horizontal registration home
position sensor (PI2P) correct?
NO
Correct the wiring.
YES
Is there any problem with the horizontal registrati on mechanism?
YES
Fix the mechanism.
NO
Replace the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-498.png "Page 499
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 69
5
[CC50] Horizontal registration motor abnormality MJ-1025
Is the horizontal registration home position sensor (PI2P) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and the horizontal registration home
position sensor (PI2P) correct?
NO
Correct the wiring.
YES
Is there any problem with the horizontal registrati on mechanism?
YES
Fix the mechanism.
NO
Replace the...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 69 5 [CC50] Horizontal registration motor abnormality MJ-1025 Is the horizontal registration home position sensor (PI2P) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC bo ard and the horizontal registration home position sensor (PI2P) correct? NO Correct the wiring. YES Is there any problem with the horizontal registrati on mechanism? YES Fix the mechanism. NO Replace the...
Page 500
![Page 500
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 70
[CC80] Front jogging plate motor abnormality/Alignme nt motor (front) abnormality
MJ-1022 (Front jogging plate motor abnormality)
Is the front jogging plate home position sensor (S6 ) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and front jogging motor (M3) correct?
NO
Correct the wiring.
YES
Has the rack run over the stopper of the roll?
YES
Fix it.
NO
1)...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-499.png "Page 500
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 70
[CC80] Front jogging plate motor abnormality/Alignme nt motor (front) abnormality
MJ-1022 (Front jogging plate motor abnormality)
Is the front jogging plate home position sensor (S6 ) working properly?
NO
Replace the sensor.
YES
Is the wiring between the finisher controller PC bo ard and front jogging motor (M3) correct?
NO
Correct the wiring.
YES
Has the rack run over the stopper of the roll?
YES
Fix it.
NO
1)...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 70 [CC80] Front jogging plate motor abnormality/Alignme nt motor (front) abnormality MJ-1022 (Front jogging plate motor abnormality) Is the front jogging plate home position sensor (S6 ) working properly? NO Replace the sensor. YES Is the wiring between the finisher controller PC bo ard and front jogging motor (M3) correct? NO Correct the wiring. YES Has the rack run over the stopper of the roll? YES Fix it. NO 1)...