Toshiba Estudio 230 Manual
Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 461
![Page 461
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 31
5
[E726] Transport/exit signal reception jam
(1) If the original remains in the RADF, remove it.
(2) If any paper remains in the equipment, remove it .
(3) Turn the power OFF and then back ON. If the jam still occurs, lead the following procedure.
(4) Check the connection between the RADF board and SLG board, and the connection between
the RADF board and switching power supply.
Are the connection of the connectors and...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-460.png "Page 461
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 31
5
[E726] Transport/exit signal reception jam
(1) If the original remains in the RADF, remove it.
(2) If any paper remains in the equipment, remove it .
(3) Turn the power OFF and then back ON. If the jam still occurs, lead the following procedure.
(4) Check the connection between the RADF board and SLG board, and the connection between
the RADF board and switching power supply.
Are the connection of the connectors and...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 31 5 [E726] Transport/exit signal reception jam (1) If the original remains in the RADF, remove it. (2) If any paper remains in the equipment, remove it . (3) Turn the power OFF and then back ON. If the jam still occurs, lead the following procedure. (4) Check the connection between the RADF board and SLG board, and the connection between the RADF board and switching power supply. Are the connection of the connectors and...
Page 462
![Page 462
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 32
[E731] Stop jam at the exit sensor
Is the exit roller stained?
YES
Clean the roller.
NO
Is the exit sensor working? (Perform the input check : 03-[FAX]ON/[7]/[E])
l ll l ll l l
NO
1) Check if the connector of the exit sensor is disco nnected.
2) Check if the connector CN4 on the RADF board is d isconnected.
3) Check if the connector pins are disconnected or t he harnesses are
open circuited.
4) Check if the conductor...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-461.png "Page 462
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 32
[E731] Stop jam at the exit sensor
Is the exit roller stained?
YES
Clean the roller.
NO
Is the exit sensor working? (Perform the input check : 03-[FAX]ON/[7]/[E])
l ll l ll l l
NO
1) Check if the connector of the exit sensor is disco nnected.
2) Check if the connector CN4 on the RADF board is d isconnected.
3) Check if the connector pins are disconnected or t he harnesses are
open circuited.
4) Check if the conductor...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 32 [E731] Stop jam at the exit sensor Is the exit roller stained? YES Clean the roller. NO Is the exit sensor working? (Perform the input check : 03-[FAX]ON/[7]/[E]) l ll l ll l l NO 1) Check if the connector of the exit sensor is disco nnected. 2) Check if the connector CN4 on the RADF board is d isconnected. 3) Check if the connector pins are disconnected or t he harnesses are open circuited. 4) Check if the conductor...
Page 463
![Page 463
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 33
5
[E742] Jam not reaching the reverse sensor (feeding in reverse)
Is the reverse roller stained?
YES
Clean the roller.
NO
Is the reverse sensor working? (Perform the input c heck: 03-[FAX]ON/[7]/[F])
l l ll l ll l
NO
1) Check if the connector of the reverse sensor is di sconnected.
2) Check if the connector CN4 on the RADF board is d isconnected.
3) Check if the connector pins are disconnected or t he harnesses are...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-462.png "Page 463
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 33
5
[E742] Jam not reaching the reverse sensor (feeding in reverse)
Is the reverse roller stained?
YES
Clean the roller.
NO
Is the reverse sensor working? (Perform the input c heck: 03-[FAX]ON/[7]/[F])
l l ll l ll l
NO
1) Check if the connector of the reverse sensor is di sconnected.
2) Check if the connector CN4 on the RADF board is d isconnected.
3) Check if the connector pins are disconnected or t he harnesses are...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 33 5 [E742] Jam not reaching the reverse sensor (feeding in reverse) Is the reverse roller stained? YES Clean the roller. NO Is the reverse sensor working? (Perform the input c heck: 03-[FAX]ON/[7]/[F]) l l ll l ll l NO 1) Check if the connector of the reverse sensor is di sconnected. 2) Check if the connector CN4 on the RADF board is d isconnected. 3) Check if the connector pins are disconnected or t he harnesses are...
Page 464
![Page 464
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 34
[E860] RADF jam access cover open
Is the RADF jam access cover opened?
YES
Remove the original, if any, and close the RADF jam access cover.
NO
Is the RADF jam access cover switch working? (Perfor m the input check: 03-[FAX]ON/[7]/
[C])
l l ll l ll l l
NO
1) Check if the connector of the RADF jam access cov er switch is dis-
connected.
2) Check if the connector CN8 on the RADF board is d isconnected.
3) Check if the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-463.png "Page 464
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 34
[E860] RADF jam access cover open
Is the RADF jam access cover opened?
YES
Remove the original, if any, and close the RADF jam access cover.
NO
Is the RADF jam access cover switch working? (Perfor m the input check: 03-[FAX]ON/[7]/
[C])
l l ll l ll l l
NO
1) Check if the connector of the RADF jam access cov er switch is dis-
connected.
2) Check if the connector CN8 on the RADF board is d isconnected.
3) Check if the...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 34 [E860] RADF jam access cover open Is the RADF jam access cover opened? YES Remove the original, if any, and close the RADF jam access cover. NO Is the RADF jam access cover switch working? (Perfor m the input check: 03-[FAX]ON/[7]/ [C]) l l ll l ll l l NO 1) Check if the connector of the RADF jam access cov er switch is dis- connected. 2) Check if the connector CN8 on the RADF board is d isconnected. 3) Check if the...
Page 465
![Page 465
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 35
5
5.1.5 Finisher jam
[ 1 ] Jam in bridge unit
[E910] Paper not reaching the bridge unit transport sensor-1
[E920] Paper stopping at the bridge unit transport s ensor-1
[E930] Paper not reaching the bridge unit transport sensor-2
[E940] Paper stopping at the bridge unit transport s ensor-2
Is there any paper remaining inside the bridge unit ?
YES
Remove the paper.
NO
Are the bridge unit transport sensors-1 and -2 work...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-464.png "Page 465
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 35
5
5.1.5 Finisher jam
[ 1 ] Jam in bridge unit
[E910] Paper not reaching the bridge unit transport sensor-1
[E920] Paper stopping at the bridge unit transport s ensor-1
[E930] Paper not reaching the bridge unit transport sensor-2
[E940] Paper stopping at the bridge unit transport s ensor-2
Is there any paper remaining inside the bridge unit ?
YES
Remove the paper.
NO
Are the bridge unit transport sensors-1 and -2 work...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 35 5 5.1.5 Finisher jam [ 1 ] Jam in bridge unit [E910] Paper not reaching the bridge unit transport sensor-1 [E920] Paper stopping at the bridge unit transport s ensor-1 [E930] Paper not reaching the bridge unit transport sensor-2 [E940] Paper stopping at the bridge unit transport s ensor-2 Is there any paper remaining inside the bridge unit ? YES Remove the paper. NO Are the bridge unit transport sensors-1 and -2 work...
Page 466
![Page 466
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 36
[ 2 ] Paper jam in puncher unit
[E9F0] Punching jam
MJ-1025
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J1006 on the punch controller PC b oard disconnected?
Is the harness connecting the punch controller PC board and punch home position sensor
(PI1P) open circuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the punch...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-465.png "Page 466
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 36
[ 2 ] Paper jam in puncher unit
[E9F0] Punching jam
MJ-1025
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J1006 on the punch controller PC b oard disconnected?
Is the harness connecting the punch controller PC board and punch home position sensor
(PI1P) open circuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the punch...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 36 [ 2 ] Paper jam in puncher unit [E9F0] Punching jam MJ-1025 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the connector J1006 on the punch controller PC b oard disconnected? Is the harness connecting the punch controller PC board and punch home position sensor (PI1P) open circuited? YES Connect the connector securely. Replace the harness . NO Is the punch...
Page 467
![Page 467
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 37
5
[ 3 ] Paper jam in finisher section
[EA10] Paper transport delay jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-466.png "Page 467
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 37
5
[ 3 ] Paper jam in finisher section
[EA10] Paper transport delay jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 37 5 [ 3 ] Paper jam in finisher section [EA10] Paper transport delay jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the connector J10 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir- cuited? YES Connect the connector securely. Replace the harness . NO Is the...
Page 468
![Page 468
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 38
[EA20] Paper transport stop jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the inlet sensor working properly? (Check...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-467.png "Page 468
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 38
[EA20] Paper transport stop jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the inlet sensor working properly? (Check...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 38 [EA20] Paper transport stop jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the connector J10 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir- cuited? YES Connect the connector securely. Replace the harness . NO Is the inlet sensor working properly? (Check...
Page 469
![Page 469
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 39
5
[EA30] Power-ON jam
MJ-1022
Is there any paper remaining on the transport path in the finisher?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the inlet sensor working properly? (Check the mo vement of the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-468.png "Page 469
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 39
5
[EA30] Power-ON jam
MJ-1022
Is there any paper remaining on the transport path in the finisher?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the inlet sensor working properly? (Check the mo vement of the...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 39 5 [EA30] Power-ON jam MJ-1022 Is there any paper remaining on the transport path in the finisher? YES Remove the paper. NO Is the connector J10 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir- cuited? YES Connect the connector securely. Replace the harness . NO Is the inlet sensor working properly? (Check the mo vement of the...
Page 470
![Page 470
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 40
[EA40] Finisher front door open jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the finisher connected with the equipment?
NO
Connect the finisher with the equipment.
YES
Is the connector J11 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller P C board and joint sensor (S4) open cir-
cuited?
YES...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-469.png "Page 470
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 40
[EA40] Finisher front door open jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the finisher connected with the equipment?
NO
Connect the finisher with the equipment.
YES
Is the connector J11 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller P C board and joint sensor (S4) open cir-
cuited?
YES...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 40 [EA40] Finisher front door open jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the finisher connected with the equipment? NO Connect the finisher with the equipment. YES Is the connector J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller P C board and joint sensor (S4) open cir- cuited? YES...