Toshiba Estudio 230 Manual
Here you can view all the pages of manual Toshiba Estudio 230 Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 471
![Page 471
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 41
5
[EA50] Stapling jam MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment or on the sta-
pling tray?
YES
Remove the paper.
NO
Is the jam cleared by taking off the staple cartrid ge from the finisher and removing the staple
sheet slid from the staple case?
YES
End.
NO
Is the connector J8 on the finisher controller PC b oard disconnected?
Is the harness connecting the finisher...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-470.png "Page 471
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 41
5
[EA50] Stapling jam MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment or on the sta-
pling tray?
YES
Remove the paper.
NO
Is the jam cleared by taking off the staple cartrid ge from the finisher and removing the staple
sheet slid from the staple case?
YES
End.
NO
Is the connector J8 on the finisher controller PC b oard disconnected?
Is the harness connecting the finisher...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 41 5 [EA50] Stapling jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment or on the sta- pling tray? YES Remove the paper. NO Is the jam cleared by taking off the staple cartrid ge from the finisher and removing the staple sheet slid from the staple case? YES End. NO Is the connector J8 on the finisher controller PC b oard disconnected? Is the harness connecting the finisher...
Page 472
![Page 472
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 42
[EA60] Early arrival jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the inlet sensor working properly? (Check the mo...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-471.png "Page 472
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 42
[EA60] Early arrival jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir-
cuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the inlet sensor working properly? (Check the mo...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 42 [EA60] Early arrival jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the connector J10 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (S2) open cir- cuited? YES Connect the connector securely. Replace the harness . NO Is the inlet sensor working properly? (Check the mo...
Page 473
![Page 473
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 43
5
[EA70] Stack delivery jam MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J9 on the finisher controller PC b oard disconnected?
Is the harness connecting the finisher controller P C board and stack delivery lever home
position sensor (S8) open circuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the stack delivery...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-472.png "Page 473
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 43
5
[EA70] Stack delivery jam MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J9 on the finisher controller PC b oard disconnected?
Is the harness connecting the finisher controller P C board and stack delivery lever home
position sensor (S8) open circuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the stack delivery...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 43 5 [EA70] Stack delivery jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the connector J9 on the finisher controller PC b oard disconnected? Is the harness connecting the finisher controller P C board and stack delivery lever home position sensor (S8) open circuited? YES Connect the connector securely. Replace the harness . NO Is the stack delivery...
Page 474
![Page 474
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 44
[EAF0] Stack return jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and returning roller home position
sensor (S3) open circuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the returning roller home...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-473.png "Page 474
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 44
[EAF0] Stack return jam
MJ-1022
Is there any paper remaining on the transport path in the finisher or equipment?
YES
Remove the paper.
NO
Is the connector J10 on the finisher controller PC board disconnected?
Is the harness connecting the finisher controller PC board and returning roller home position
sensor (S3) open circuited?
YES
Connect the connector securely. Replace the harness .
NO
Is the returning roller home...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 44 [EAF0] Stack return jam MJ-1022 Is there any paper remaining on the transport path in the finisher or equipment? YES Remove the paper. NO Is the connector J10 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and returning roller home position sensor (S3) open circuited? YES Connect the connector securely. Replace the harness . NO Is the returning roller home...
Page 475
![Page 475
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 45
5
[ 4 ] Paper jam in saddle stitcher section
[EAB0] Saddle paper transport stop jam
MJ-1025
Is there any paper remaining on the paper transport path in the saddle stitcher section in the
finisher?
YES
Remove the paper.
NO
Is the connector CN16 (folding position sensor) on the finisher controller PC board discon-
nected?
Is the harness connecting the finisher controller PC board and folding position sensor open-...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-474.png "Page 475
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 45
5
[ 4 ] Paper jam in saddle stitcher section
[EAB0] Saddle paper transport stop jam
MJ-1025
Is there any paper remaining on the paper transport path in the saddle stitcher section in the
finisher?
YES
Remove the paper.
NO
Is the connector CN16 (folding position sensor) on the finisher controller PC board discon-
nected?
Is the harness connecting the finisher controller PC board and folding position sensor open-...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 45 5 [ 4 ] Paper jam in saddle stitcher section [EAB0] Saddle paper transport stop jam MJ-1025 Is there any paper remaining on the paper transport path in the saddle stitcher section in the finisher? YES Remove the paper. NO Is the connector CN16 (folding position sensor) on the finisher controller PC board discon- nected? Is the harness connecting the finisher controller PC board and folding position sensor open-...
Page 476
![Page 476
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 46
[ 5 ] Other paper jam
[EAD0] Print end command time-out jam
Is the main motor rotating normally?
NO
1) Replace the SYS board.
2) Replace the LGC board.
[EAE0] Receiving time time-out jam Is the finisher working?
YES
Replace the finisher controller PC board.
NO
1) Check if the voltage (24V) is being supplied to t he finisher.
2) Check the connection of the LGC board and IPC boa rd.
3) Check if the harness connecting the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-475.png "Page 476
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 46
[ 5 ] Other paper jam
[EAD0] Print end command time-out jam
Is the main motor rotating normally?
NO
1) Replace the SYS board.
2) Replace the LGC board.
[EAE0] Receiving time time-out jam Is the finisher working?
YES
Replace the finisher controller PC board.
NO
1) Check if the voltage (24V) is being supplied to t he finisher.
2) Check the connection of the LGC board and IPC boa rd.
3) Check if the harness connecting the...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 46 [ 5 ] Other paper jam [EAD0] Print end command time-out jam Is the main motor rotating normally? NO 1) Replace the SYS board. 2) Replace the LGC board. [EAE0] Receiving time time-out jam Is the finisher working? YES Replace the finisher controller PC board. NO 1) Check if the voltage (24V) is being supplied to t he finisher. 2) Check the connection of the LGC board and IPC boa rd. 3) Check if the harness connecting the...
Page 477
![Page 477
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 47
5
5.1.6 Drive system related service call
[C010] Main motor is abnormal
Is the main motor working? (Perform the output check in the test mode: 03-101/151)
l l l l l ll l
NO
1) Check if the connector CN1 of the main motor is d isconnected.
2) Check if the connector CN305 on the LGC board is disconnected.
3) Check if the connector pins are disconnected and the harnesses are
open circuited.
4) Check if the conductor...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-476.png "Page 477
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 47
5
5.1.6 Drive system related service call
[C010] Main motor is abnormal
Is the main motor working? (Perform the output check in the test mode: 03-101/151)
l l l l l ll l
NO
1) Check if the connector CN1 of the main motor is d isconnected.
2) Check if the connector CN305 on the LGC board is disconnected.
3) Check if the connector pins are disconnected and the harnesses are
open circuited.
4) Check if the conductor...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 47 5 5.1.6 Drive system related service call [C010] Main motor is abnormal Is the main motor working? (Perform the output check in the test mode: 03-101/151) l l l l l ll l NO 1) Check if the connector CN1 of the main motor is d isconnected. 2) Check if the connector CN305 on the LGC board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor...
Page 478
![Page 478
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 48
5.1.7 Paper feeding system related service call
[C040] PFP motor is abnormal
Is the PFP motor working? (Perform the output check i n the test mode: 03-109/159)
l l l l ll l ll l ll l ll l l
NO
1) Check if the signal line connector CN503 of the P FP motor is discon-
nected.
2) Check if the power line connector CN502 of the PFP motor is discon-
nected.
3) Check if the connector CN246 on the PFP board is disconnected.
4)...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-477.png "Page 478
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 48
5.1.7 Paper feeding system related service call
[C040] PFP motor is abnormal
Is the PFP motor working? (Perform the output check i n the test mode: 03-109/159)
l l l l ll l ll l ll l ll l l
NO
1) Check if the signal line connector CN503 of the P FP motor is discon-
nected.
2) Check if the power line connector CN502 of the PFP motor is discon-
nected.
3) Check if the connector CN246 on the PFP board is disconnected.
4)...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 48 5.1.7 Paper feeding system related service call [C040] PFP motor is abnormal Is the PFP motor working? (Perform the output check i n the test mode: 03-109/159) l l l l ll l ll l ll l ll l l NO 1) Check if the signal line connector CN503 of the P FP motor is discon- nected. 2) Check if the power line connector CN502 of the PFP motor is discon- nected. 3) Check if the connector CN246 on the PFP board is disconnected. 4)...
Page 479
![Page 479
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 49
5
[C130] Upper drawer tray is abnormal
[C140] Lower drawer tray is abnormal
Does the tray go up? (Perform the output check in t he test mode: 03-242/243)
l l l l l ll
NO
1) Check if the connector of the tray-up motor is dis connected.
2) Check if the connector CN307 on the LGC board is disconnected.
3) Check if the connector pins are disconnected and the harnesses are
open circuited.
4) Check if the conductor pattern...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-478.png "Page 479
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING
5 - 49
5
[C130] Upper drawer tray is abnormal
[C140] Lower drawer tray is abnormal
Does the tray go up? (Perform the output check in t he test mode: 03-242/243)
l l l l l ll
NO
1) Check if the connector of the tray-up motor is dis connected.
2) Check if the connector CN307 on the LGC board is disconnected.
3) Check if the connector pins are disconnected and the harnesses are
open circuited.
4) Check if the conductor pattern...")
June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTING 5 - 49 5 [C130] Upper drawer tray is abnormal [C140] Lower drawer tray is abnormal Does the tray go up? (Perform the output check in t he test mode: 03-242/243) l l l l l ll NO 1) Check if the connector of the tray-up motor is dis connected. 2) Check if the connector CN307 on the LGC board is disconnected. 3) Check if the connector pins are disconnected and the harnesses are open circuited. 4) Check if the conductor pattern...
Page 480
![Page 480
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 50
[C150] PFP upper drawer tray is abnormal
[C160] PFP lower drawer tray is abnormal
Does the tray go up? (Perform the output check in t he test mode: 03-278/280)
l ll l l l ll l l
NO
1) Check if the connector of the tray-up motor is dis connected.
2) Check if any of the connectors CN241, CN242 and C N244 on the
PFP board is disconnected.
3) Check if the connector CN310 on the LGC board is disconnected.
4) Check if the...](http://img.usermanuals.tech/thumb/76/103453/w300_estudio-230-manual-1513181221_d-479.png "Page 480
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC
5 - 50
[C150] PFP upper drawer tray is abnormal
[C160] PFP lower drawer tray is abnormal
Does the tray go up? (Perform the output check in t he test mode: 03-278/280)
l ll l l l ll l l
NO
1) Check if the connector of the tray-up motor is dis connected.
2) Check if any of the connectors CN241, CN242 and C N244 on the
PFP board is disconnected.
3) Check if the connector CN310 on the LGC board is disconnected.
4) Check if the...")
e-STUDIO200L/202L/230/232/280/282 TROUBLESHOOTINGJune 2004 © TOSHIBA TEC 5 - 50 [C150] PFP upper drawer tray is abnormal [C160] PFP lower drawer tray is abnormal Does the tray go up? (Perform the output check in t he test mode: 03-278/280) l ll l l l ll l l NO 1) Check if the connector of the tray-up motor is dis connected. 2) Check if any of the connectors CN241, CN242 and C N244 on the PFP board is disconnected. 3) Check if the connector CN310 on the LGC board is disconnected. 4) Check if the...