Toshiba E Studio 207 User Manual
Have a look at the manual Toshiba E Studio 207 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
To Print Lists 29 NIC status page You can print out the setting status of the NIC (Network Interface Card) of the Network Printer Kit (optional). 1Press the [USER FUNCTIONS] button. The “user functions mode” main screen appears. 2Press or to select LISTS, and then press the [ENTER] button. 3Press or to select NIC STATUS PAGE, and then press the [ENTER] button. “Printing accepted” appears and the NIC status page is printed out. USER FUNCTIONS1216 01.DEFAULT SETTINGS 02.LISTS 03.INITIAL SETUP LISTS 4.ITU MAILBOX 5.CONFIGURATION PAGE 6.NIC STATUS PAGE Downloaded From ManualsPrinter.com Manuals
5.CONFIGURING NETWORKS (EQUIPMENT) This chapter describes how to configure networks using the control panel of this equipment. Network Configuration from Equipment...............................................................32 Ethernet Configuration ...........................................................................................33 TCP/IP Configuration ..............................................................................................35 IPX/SPX Configuration...........................................................................................40 AppleTalk Configuration ........................................................................................42 HTTP Configuration ................................................................................................44 Downloaded From ManualsPrinter.com Manuals
5 CONFIGURING NETWORKS (EQUIPMENT) 32 Network Configuration from Equipment Network Configuration from Equipment You can perform the following network configurations using the [USER FUNCTIONS] button: P.33 “Ethernet Configuration” P.35 “TCP/IP Configuration” P.40 “IPX/SPX Configuration” P.42 “AppleTalk Configuration” P.44 “HTTP Configuration” To use TopAccess: Before using a web-based utility TopAccess, TCP/IP protocol and HTTP network server service must be configured in this equipment. P.35 “TCP/IP Configuration” P.44 “HTTP Configuration” When TCP/IP and HTTP have been configured, you can use TopAccess on your computer. Once TopAccess is enabled, all the network configurations including the reconfiguration of TCP/ IP and HTTP can be executed from TopAccess screen. For the network configurations using TopAccess, see the following page: P.86 “Setting up Network Settings (Printing Function)” Downloaded From ManualsPrinter.com Manuals
Ethernet Configuration 33 Ethernet Configuration You can specify the link speed and communication mode of Ethernet. 1Press the [USER FUNCTIONS] button when the ready screen is displayed. The “user functions mode” main screen appears. 2Press or to select INI- TIAL SETUP, and then press the [ENTER] button. 3Press or to select NET- WORK, and then press the [ENTER] button. 4Press or to select ETH- ERNET, and then press the [ENTER] button. 5Press or to select LINK SPEED/DUPLEX MODE, and then press the [ENTER] but- ton. 6Press or to select the desired link speed and com- munication mode. USER FUNCTIONS00001216 01.DEFAULT SETTINGS 02.LISTS 03.INITIAL SETUP INITIAL SETUP 03.DRAWER SET POP-UP 04.TERMINAL ID 05.NETWORK NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP ETHERNET 01.LINK SPEED/DUPLEX MODE LINK SPEED/DUPLEX MODE 1.AUTO 2.10BASE/HALF 3.10BASE/FULL LINK SPEED/DUPLEX MODE 3.10BASE/FULL 4.100BASE/HALF 5.100BASE/FULL Downloaded From ManualsPrinter.com Manuals
5 CONFIGURING NETWORKS (EQUIPMENT) 34 Ethernet Configuration 7Press the [ENTER] button. The screen returns to the shown in step 5. 10Press the [CANCEL] button once or press the [FUNCTION CLEAR] button to return the screen to the “user function mode” main screen. If the network connection is still unstable even after following the procedure above, turn the power of this equipment OFF and then back ON.AUTO: Detects the Ethernet link speed automatically. 10BASE/HALF: Uses 10BASE-T half-duplex communication mode. 10BASE/FULL: Uses 10BASE-T full-duplex communication mode. 100BASE/HALF: Uses 100BASE-TX half-duplex communication mode. 100BASE/FULL: Uses 100BASE-TX full-duplex communication mode. yWhen you select other than AUTO above, refer to the specifications of the network to which this equipment is connected. yIf you are not sure of the most appropriate link speed or communication mode, select AUTO. 8Press the [CANCEL] button once to return the screen to the NETWORK menu screen. If you press the [CANCEL] button more than twice and exit the NETWORK menu, the NIC initialization operation in the next step becomes ineffective. In this case, repeat the procedure from step 1. 9Press or to select COM- PLETE, and then press the [ENTER] button. The initialization starts and “Initializing” appears. When it is completed, “Operation Completed” appears and the screen returns to the one shown in step 3. NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP Downloaded From ManualsPrinter.com Manuals
TCP/IP Configuration 35 TCP/IP Configuration You can configure TCP/IP protocol. This TCP/IP configuration includes address assignment method selection, IP address, subnet mask, and default gateway assignment (manual assign- ment). yThe configuration of TCP/IP protocol differs depending on your network environments. yBefore using a web-based utility TopAccess, TCP/IP protocol and HTTP network server ser- vice must be configured in this equipment. For HTTP configuration, see the following page: P.44 “HTTP Configuration” Configuring TCP/IP using DHCP or Auto IP function: If you are not sure of the proper TCP/IP configuration method to assign an address to this equip- ment, select “DYNAMIC” for the address assignment method. When you select “DYNAMIC”, this equipment obtains an IP address, subnet mask and gateway from a DHCP server, if your net- work supports DHCP. If your network does not support it, the Auto IP function will assign a proper IP address to this equipment. Configuring TCP/IP using only DHCP: When you connect this equipment to a local area network including a DHCP server and config- ure TCP/IP for this equipment using only DHCP, without the Auto IP function, select “NO AUTOIP” for the address assignment method. When you select “NO AUTOIP”, this equipment obtains an IP address, subnet mask and gateway from the DHCP server. The automatic IP address assignment with the Auto IP function is disabled. Connecting to local area network requiring static IP addresses: When you connect this equipment to a local area network requiring a static IP address, select “STATIC IP” for the address assignment method and specify the IP address manually. Subnet mask and default gateway should also be configured as required. Automatic IP address assignment 1Press the [USER FUNCTIONS] button when the ready screen is displayed. The “user functions mode” main screen appears. 2Press or to select INI- TIAL SETUP, and then press the [ENTER] button.USER FUNCTIONS00001216 01.DEFAULT SETTINGS 02.LISTS 03.INITIAL SETUP Downloaded From ManualsPrinter.com Manuals
5 CONFIGURING NETWORKS (EQUIPMENT) 36 TCP/IP Configuration 7Press the [ENTER] button. The screen returns to the shown in step 5. 3Press or to select NET- WORK, and then press the [ENTER] button. 4Press or to select TCP/ IP, and then press the [ENTER] button. 5Press or to select ADDRESS MODE, and then press the [ENTER] button. 6Press or to select the desired method of automatic IP address assignment. DYNAMIC: Obtains an IP address automatically using the Auto IP function and DHCP. NO AUTOIP: Obtains an IP address automatically using DHCP. 8Press the [CANCEL] button once to return the screen to the NETWORK menu screen. If you press the [CANCEL] button more than twice and exit the NETWORK menu, the NIC initialization operation in the next step becomes ineffective. In this case, repeat the procedure from step 1. 9Press or to select COM- PLETE, and then press the [ENTER] button. The initialization starts and “Initializing” appears. When it is completed, “Operation Completed” appears and the screen returns to the one shown in step 3. INITIAL SETUP 03.DRAWER SET POP-UP 04.TERMINAL ID 05.NETWORK NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP TCP/IP 01.ADDRESS MODE 02.IP ADDRESS 03.SUBNET MASK ADDRESS MODE 1.STATIC IP 2.DYNAMIC 3.NO AUTOIP NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP Downloaded From ManualsPrinter.com Manuals
TCP/IP Configuration 37 10Press the [CANCEL] button once or press the [FUNCTION CLEAR] button to return the screen to the “user function mode” main screen. You can check the configuration status and the obtained value if you print out the NIC status page. P.29 “NIC status page” Manual IP address assignment 1Press the [USER FUNCTIONS] button when the ready screen is displayed. The “user functions mode” main screen appears. 2Press or to select INI- TIAL SETUP, and then press the [ENTER] button. 3Press or to select NET- WORK, and then press the [ENTER] button. 4Press or to select TCP/ IP, and then press the [ENTER] button. 5Press or to select ADDRESS MODE, and then press the [ENTER] button. USER FUNCTIONS00001216 01.DEFAULT SETTINGS 02.LISTS 03.INITIAL SETUP INITIAL SETUP 03.DRAWER SET POP-UP 04.TERMINAL ID 05.NETWORK NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP TCP/IP 01.ADDRESS MODE 02.IP ADDRESS 03.SUBNET MASK Downloaded From ManualsPrinter.com Manuals
5 CONFIGURING NETWORKS (EQUIPMENT) 38 TCP/IP Configuration 6Press or to select STATIC IP, and then press the [ENTER] button. The screen returns to the one shown in step 5. 7Press or to select IP ADDRESS, and then press the [ENTER] button. 8Enter the IP address, and then press the [ENTER] button. The screen returns to the one shown in step 7. 9Press or to select SUB- NET MASK, and then press the [ENTER] button. 10Key in the subnet mask value as required, and then press the [ENTER] button. The screen returns to the one shown in step 9. 11Press or to select DEFAULT GATEWAY, and then press the [ENTER] button. 12Key in the default gateway value as required, and then press the [ENTER] button. 13Press the [CANCEL] button once to return the screen to the NETWORK menu screen. If you press the [CANCEL] button more than twice and exit the NETWORK menu, the NIC initialization operation in the next step becomes ineffective. In this case, repeat the procedure from step 1. ADDRESS MODE 1.STATIC IP 2.DYNAMIC 3.NO AUTOIP TCP/IP 01.ADDRESS MODE 02.IP ADDRESS 03.SUBNET MASK IP ADDRESS XXX.XXX.XXX.XXX TCP/IP 01.ADDRESS MODE 02.IP ADDRESS 03.SUBNET MASK SUBNET MASK XXX.XXX.XXX.XXX TCP/IP 02.IP ADDRESS 03.SUBNET MASK 04.DEFAULT GATEWAY DEFAULT GATEWAY XXX.XXX.XXX.XXX NETWORK 01.COMPLETE 02.ETHERNET 03.TCP/IP Downloaded From ManualsPrinter.com Manuals