Starplus Triad S System Programming Manual

10-4LC R Tab l e s
LCR Tables
3- Di git Table
The 3-Digit  Table is divided into two sections: Leading 1 (1 is  dialed 
before the number) and Non-Leading 1 (no 1 is dialed before the 
number). This gives the  system the  ability to handle call routing in areas 
tha t re qui re  a 1 bef ore  a long  di st ance numbe r as wel l as in ar eas  t hat  do 
not require the  1.
6- Di git Table  (Of fic e Co des )
The 6-Digit Tab le can accommoda te 20 in dexes. Each ind ex is  as socia ted 
wit h a n ar e a...

LC R Tab l e s10-5
Inse rt/Dele te Tables
There are 20  Insert/Delete  Tables.  Up to 20-digits, including pauses, can 
be  ins er te d a nd up  to  16 -d igi ts  de le te d.  To i nsur e  th at  a pa use  is  i nse rt ed  
in LCR at def aul t, th e d ata bas e prog ram ming  has  be en change d t o ad d a 
paus e i n e ac h o f t he 2 0  LC R  Ins er t  and  Del e te  Ta bl es  and  Ins er t  Tab le  0  in 
each of the route tables.
LCR Routing for Toll Information
The LCR Routing  for Toll Information...

10-6LC R Tab l e s
Figure 10-1: LCR Flowchart
ROUTE
ASSIGNED
FROM
6-DIGIT
TABLE 

LC R Op e r a ti o n 1 0- 7
LCR Operation
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode.
1. Press FLASH and  di al [75]. The  following message displays:
2 . The re  ar e  ei ght  t abl es  whi c h c an  be  pr ogra mmed  he re  for  LCR  (y ou 
m ust  al so p rogr am  LC R Cl ass  of S er v ice  in  St at ion  Pr ogr ammi ng).  Use 
t he  pr oc edur es  l is te d be l ow  to  pr ogra m t...

10-8 L CR O peratio n
3- Di git Area / O ff ice  Cod e Table
Pro g ram mi ng  S te ps
1. Press the 3-DIGIT TABLE  flexible bu tton ( FLASH 75, Butto n #1). The 
following message displays:
L  =  [ 0]  fo r  N o n- L e a d i ng  1 (1  n o t  d i a l e d ),  [1 ] f or  L e ad i n g  1  ( 1 i s d i a l e d)
NNN =  A rea/Of fice  Code
RR   =  Ro u t e  L i s t  N u mb e r  0 0- 15
Y = [0] Do not go to 6-digit table, [1] Go to 6-digit table
PP  =  Number of  digits  expe cted  to  be  dialed.
2. Press the...

LC R Op e r a ti o n 1 0- 9
6- Di git O ff ice  Cod e Table
Pro g ram mi ng  S te ps
1. Press the 6-DIGIT TABLE  flexible bu tton ( FLASH 75, Butto n #2). The  
following message displays:
6 = [0] to remove codes, [1] to add codes
AAA = Area Code
RR  = Ro u t e  N u mb e r  0 0- 15
NNN = Office  Code
2. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay u pdat es .
3 . Ent er  a ddit i onal  offi ce  codes  t o be  pr ogra mme d i nto  the  s ame  Are a...

10-1 0 L CR O peratio n
Exce ptio n Cod e Table
Pro g ram mi ng  S te ps
1 . Pr es s E XCEP T IO N TA BLES  fl exi bl e b utt on ( FLASH 75, Butto n #3 ). The 
following message displays:
6 = [0]  to  remove code from table, [1] to  add code to table
XX = Exception codes for singl e digit codes , press  MUTE button as 2nd digit. 
(T he  [
6] may be entered as the 1s t digit only.)
RR = Route T able Num ber 00–15
2. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl...

LC R Op e r a ti o n 10 - 11
2. To  create an entry, dial:
a. [RR]
b. [T]
c. [GG]
d. [DD ]
e. [L]
3. Press [HOLD] to save the entry. A confirmation tone is heard and the 
display updates.
4. To enter additional CO Line groups in the same Time Period Route 
List number:
a. Di al  [GG]
b. Di al  [DD ]
c. Dial [L]
d. Pre ss [HO LD]
Entering  Data for a Diffe rent  Time Pe riod Route  List
1. Press program FLASH 75, Butto n #4 and  ent er  a ll  da ta  
(RR T GG DD L).
2. Repeat the  above to program a new...

10-1 2 L CR O peratio n
Des crip ti on
Each  of t he  1 6  Rou te  Li st  T abl es  ava il abl e  conta ins  four  T im e Pe ri od 
R o u ti ng  Lis ts , o ne  fo r  e ac h o f t he  4  dai ly  st ar t  ti me  pe ri o ds.  Wi thi n e ac h 
Ti me  Per iod  Route  Li st  up  t o 7  CO  (out si de ) l ine  gr oups  and  t hei r 
corresponding Insert/Delete table, if any, and LCR Class Of Service Priority 
ar e p rogr am med  on a  pe r l i ne  group  ba sis .
Whe n r outi ng  a C O ca ll  t hrou gh LC R, C...

LC R Op e r a ti o n 10 - 13
A station using LCR is able to use only those CO (outside) line groups with 
a pr i ori ty  ass ignm ent  of e qual  or  highe r  val ue t han  the  st at ion’s LC R Cl ass  
of Service (e.g., a station with  LCOS  3 can use line groups with a  priority 
be twe en 3 and 6).
In se rt  /  D el et e Ta b le
Pro g ram mi ng  S te ps
1. Press INSERT/DELETE TABLE flexible  button (FLA SH 75 , Bu tton #5). 
The following  message displays:
Tabl e 1 0-1 :  LCR Cl ass  o f Se rvi ce...