Starplus Triad S System Programming Manual

10-1 4 L CR O peratio n
2. Enter the  table information as follows:
†T T = Insert/Delete Table Number 00–19
†X =  [0] Pre-D el ete  numbe rs (f irst di gits  di ale d i n the  numb er),
-or -
[1]  P re -I nser t  num ber s  (ins er t  di gi ts  i n fr ont  of num ber  d ial ed,
-or -
[2] Post-Insert num bers  (ins ert digits  be hind  numb er dialed).
DDD  =  Di gi ts  (u p  to   16 -di gi ts  may  be  de le te d fr o m  the  be gi nning
of t he  numbe r  di ale d a nd up  t o 4 0 d igi t s ca n be  i...

LC R Op e r a ti o n 10 - 15
For  i nst ance , O the r  Comm on Ca rr ie r  (O CC)  acces s cod es  and 
aut hori z at ion  (ID ) code s  ca n be  a utoma ti cal ly  ins er t ed  by t he  sys te m 
ei th er  i n fr ont  of,  and/ or  be hin d t he  numbe r  dia le d.  The re  ar e  tw ent y 
Ins er t /D el et e  Tab le s a nd e ac h  all ows  ent r ie s i n a  de le te  t abl e  and  a p re - 
and  post  i nse rt  t ab le . Up  t o 4 0 d igi t s (i ncl uding  pa uses ) can  be  i nser t ed 
(2 0 p re  an...

10-1 6 L CR O peratio n
Weekly Tim e  Table -- With the  wide selection of Common  Carriers, the 
le ast  c os tl y r out e  for  a p ar ti c ula r a re a  cod e m ay b e  dif fer ent  a t  dif fer en t 
ti me s o f  t he d ay.  To   ac c o mmo da te  t his  si t u at io n,  th is  ta bl e a nd t he  
We ekl y T ime  T abl e  work  t oget her ,  div idi ng  the  da y i nto  four  pos si ble  
time periods. By  default these  tables  are set at the standard divisions of 
8AM,  5PM, and 11PM.  However,...

LC R Op e r a ti o n 10 - 17
[2] =  Wedn esd ay
[3] =  Thursda y
[4] =  Friday
[5] =  Sa turday
[6] =  Sund ay
T =  Ti me  Period  Route  Li st (1- 4)  to  use  for the ti me- of-d ay (b ase d on 
the  D ail y St ar t Ti me ta bl e). Ent er  va lu e s f o r all  t i me per i o ds s pe ci fi ed  
in the  D ail y St ar t Ti me ta bl e f o r tha t d ay.
Fi r s t  T =  T ime  Per iod  Route  Li st  for  the  FI RST  Dai l y St ar t  Ti me  (app li es  
to   al l R o u t e  Li st  t abl es ).
Seco nd T = Time...

10-1 8 L CR O peratio n
Ex a m pl e
If  a  ca ll  i s p la ced  at  5: 45  p m on  a Monda y, t he n accor di ng t o t he  Dai ly  
St ar t Ti me Tab le  (us ing def aul t val ues ) t he ent ry  for  t ime  p er iod tw o of 
the weekly  schedule is checked. Because it  is Monday the  entry for time 
period two on  Monday  is used and the result is that the  Time  Period 
Route List num ber two (a gain us ing  def ault  values ) is us ed  for all  routes .
Thus , t he  c all  i s r out ed a c c ordi ng t...

LC R Op e r a ti o n 10 - 19
Des crip ti on
The LCR Routing  for Toll Information  feature  adds provisions to the LCR 
c al l p roc e ssi ng whic h al lows  c ommon c all  r out ing for  al l tol l  in form ati on 
calls. 1-(XXX) 555-1212, (XXX) 555-1212,  1-555-1212, and 555-1212 calls 
ar e i nt er c ep te d a nd se nt  t o a  se le c te d r out e i n t he  R out e L ist  T abl e . 
Numbe r s di al ed  ar e  int eg rat e d an d i f i t  is  de te rm ine d t o be  a  t oll  
information call, either...

10-2 0 L CR O peratio n 

11
Initializing Database
Parameters
This c hapter desc ribes the proc edures and  steps necessary to
initialize the system database, returning any programmed data to its
original or default value. 

Introduction 11-3
Introduction
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode  to 
initialize Database Parameters.
Pr es s F LASH and dia l [80]. The  fol lowi ng m es sage  di sp lays :
Des crip ti on
This  section lets portions of the database  be  initialized individually. The 
only  way  to  in it ia li ze  t he  ent i re  da tab ase  i s t o m ove  swi tc h  #1  on  the  
BKSU board to...