Sony Projector Vpl Vw11ht User Manual

							21 (GB)
Using the MENU
The projector is equipped with an on-screen menu for
making various adjustments and settings.
You can select the language for displaying in the
menu.
For details on the selecting the language used in the menu,
see page 17 (GB).
1Press the MENU key.
The menu display appears.
The menu presently selected is shown as a yellow
button.
PICTURE CTRL
CONTRAST: 80
BRIGHT: 50
RGB ENHANCER:30
COLOR TEMP: LOWINPUT-A
2Use the M or m key to select a menu, then press
the , or ENTER key.
The selected menu appears.
SET SETTING
STATUS: ON
INPUT-A: COMPONENT
INPUT-B: COMPONENT
LANGUAGE: ENGLISH
POWER SAVING:OFFSIRCS RECEIVER:FRONT&REARINPUT-A
3Select an item.
Use the M or m key to select the item, then press
the , or ENTER key.
4Adjust an item.
¥ When changing the adjustment level:
To increase the number, press the M or , key.
To decrease the number, press the m or < key.
Press the ENTER key to restore the original
screen.
¥ When changing the setting:
Press the M or m key to change the setting.
Press the < or ENTER key to restore the
original screen.
For details on setting individual items, see the relevant
menu pages.
Menus           Setting items
To clear the menu display
Press the MENU key.
The menu display disappears automatically if no key
is pressed for one minute.
To reset items that have been adjusted
Press the RESET key.
ÒComplete!Ó appears on the screen and the settings
appearing on the screen will be reset to their factory
preset values.
Items which can be reset are:
¥ ÒCONTRASTÓ, ÒBRIGHTÓ, ÒCOLORÓ, ÒHUEÓ,
ÒSHARPÓ and ÒRGB ENHANCERÓ in the
PICTURE CTRL menu.
¥ ÒDOT PHASEÓ, ÒSIZE HÓ and ÒSHIFTÓ in the
INPUT SETTING menu.
About the memory of the settings
The settings are automatically stored in the projector
memory.
When no signal is input
When there is no input signal, ÒNO INPUTÐCannot
adjust this item.Ó appears on the screen, and each item
cannot be adjusted.
Using the MENU
Adjustments and settings using the menu
Adjustments and settings using the menu 
						

							22 (GB)
The PICTURE CTRL Menu
The PICTURE CTRL (control) menu is used for
adjusting the picture.
Unadjustable items depending on the input signal are
not displayed in the menu.
CONTRAST
Adjusts the picture contrast.
The higher the setting, the greater the contrast.
The lower the setting, the lower the contrast.
BRIGHT
Adjusts the picture brightness.
The higher the setting, the brighter the picture.
The lower the setting, the darker the picture.
COLOR
Adjusts color intensity.
The higher the setting, the greater the intensity.
The lower the setting, the lower the intensity.
HUE
Adjusts color tones.
The higher the setting, the picture becomes greenish.
The lower the setting, the picture becomes purplish.
SHARP
Adjusts the picture sharpness.
The higher the setting, the sharper the picture.
The lower the setting, the softer the picture.
RGB ENHANCER
Adjusts the picture sharpness when the computer
signals are input.
The higher the setting, the sharper the picture.
The lower the setting, the softer the picture.
D. (Dynamic) PICTURE
Emphasizes the black color.
ON: Emphasizes the black color to produce a bolder
ÒdynamicÓ picture.
OFF: Reproduces the dark portions of the picture
accurately, in accordance with the source signal.
COLOR TEMP
Adjusts the color temperature.
HIGH: Makes the white color bluish.
LOW: Makes the white color reddish.
COLOR SYS (System)
Selects the color system of the input signal.
AUTO: Automatically selects one of the following
signals: NTSC 
3.58, PAL, SECAM, NTSC4.43.
PAL-M/N: Automatically selects one of the
following signals: PAL-M/PAL-N, NTSC
3.58.
Normally, set to AUTO.
If the picture is distorted or colorless, select the color
system according to the input signal.
DRC-MF
Smoothes out a large size video image.
DRC ´ 4: Doubles the number of the video signal
scanning lines and the number of horizontal
pixels, resulting in quadrupled image quality.
DRC PROGRESSIVE: Displays a clear line or
characters without line flickering.
The PICTURE CTRL Menu
When the video signal is input
When the RGB signal is input
PICTURE CTRL
CONTRAST: 80
BRIGHT: 50
COLOR: 50
HUE: 50
SHARP: 50
D.PICTURE: ON
COLOR TEMP: HIGH
COLOR SYS: AUTO
DRC-MF: DRCx4VIDEO
PICTURE CTRL
CONTRAST: 80
BRIGHT: 50
RGB ENHANCER:30
COLOR TEMP: HIGHINPUT-A 
						

							23 (GB)
(NTSC3.58/
4.43 only)
Input signals and adjustable/setting items
Input signal
Video or Compo-Pro-RGB1)B&W
S video (Y/C) nent/
gres-
15k RGBsive
Compo-
nent/
HDTV/
DTV
CONTRAST
BRIGHT
COLORÐÐ
HUE
ÐÐ
SHARPÐ
RGBÐÐÐÐ
ENHANCER
D. PICTURE
ÐÐ
COLOR
TEMP
COLOR
ÐÐÐ
SYS
DRC-MF
ÐÐ
 : Adjustable/can be set
Ð : Not adjustable/can not be set
The INPUT SETTING Menu
The INPUT SETTING menu is used to adjust the
input signal.
Unadjustable items depending on the input signal are
not displayed in the menu.
DOT PHASE
Adjusts the phase of the LCD dots and the computer
signal input from the INPUT A/B connector.
Adjust the picture to where it looks clearest.
SIZE H
Adjusts the horizontal size of the picture input from
the INPUT A/B connector.
The higher the setting, the larger the horizontal size of
the picture. The lower the setting, the smaller the
horizontal size of the picture. Adjust the setting
according to the dots of the input signal. For details on
the suitable value for the preset signals, see page 26
(GB).
When the video signal is input
When the RGB signal is input
Signal type Signal type
INPUT SETTING
ASPECT: FULL
VIDEO MEMORY: OFF
VIDEO/60VIDEO
INPUT SETTING
DOT PHASE: 16
SIZE  H: 1056
SHIFT H: 123 V: 123
SCAN CONV: ON
VIDEO MEMORY: OFF
800x600INPUT-A
The PICTURE CTRL Menu / The INPUT SETTING Menu
.........................................................................................................................................................................................................
1) The RGB signals of a computer
Item 
						

							24 (GB)
SHIFT
Adjusts the position of the picture input from the
INPUT A/B connectors.
H adjusts the horizontal position of the picture.
V adjusts the vertical position of the picture.
As the setting for H increases, the picture moves to
the right, and as the setting decreases, the picture
moves to the left.
As the setting for V increases, the picture moves up,
and as the setting decreases, the picture moves down.
Use the < or the , key to adjust the horizontal
position and the M and m key for the vertical position.
ASPECT
Sets the following aspect setting:
4:3NORMAL, NORMAL THROUGH
16:9
FULL, FULL THROUGH, ZOOM, SUBTITLE,
WIDE ZOOM.
FULL: The 16:9 squeezed image is displayed with
the correct aspect.  The 4:3 image is enlarged
horizontally.
FULL THROUGH: One-to-one mapping is done on
a squeezed 16:9 image. The image is displayed at
the center of the screen.
NORMAL: The picture with normal ratio 4:3 is
displayed.
The INPUT SETTING Menu
Good morning.
How are you?
NORMAL THROUGH: One-to-one mapping is
done on the picture with a normal ratio of 4:3.  The
picture is displayed at the center of the screen.
ZOOM: The picture with normal ratio 4:3 is enlarged
vertically and horizontally (with same ratio) to the
screen size. This mode is ideal for capturing the full-
screen drama of wide-format movies.
SUBTITLE: The subtitle area is compressed. This
mode leaves the subtitles on the lower part of the
screen.
WIDE ZOOM: The picture with normal ratio 4:3 is
enlarged and the upper and lower portions of the
picture are compressed. This is ideal for general
programs, such as news or variety shows.
Note
You cannot change the image mode while the projector
is projecting a high definition image or DTV signal.
The adjustable/unadjustable items
depending on the aspect setting
ItemsV TITLE DIGITSCROLL AREA KEYSTONE
FULL Ð Ð
FULL THROUGHÐÐÐ
NORMAL Ð Ð
NORMAL Ð Ð Ð
THROUGH
ZOOMÐ
SUBTITLEÐ
WIDE ZOOM Ð Ð Ð
 : Adjustable Ð : Unadjustable
INPUT SETTINGVIDEO
ASPECT:VIDEO MEMORY:
VIDEO/60FULL
FULL THROUGH
NORMAL
NORMAL THROUGHZOOM
SUBTITLE
WIDE ZOOM 
						

							25 (GB)
The INPUT SETTING Menu
SCAN CONV (Scan converter)
Converts the signal to display the picture according to
the screen size.
ON: Enlarges the picture according to the screen
aspect. The picture will lose some clarity.
OFF: 
Displays the picture while matching one pixel of
input picture element to that of the LCD. The picture
will be clear but the picture size will be smaller.
Note
When the XGA or SXGA signal is input, this item
will not be displayed.
V SCROLL
Adjusts the vertical position of the picture.
Adjustable range is 0 to +7.
As the setting increases, the picture moves up, and as
the setting decreases, the picture moves down. To
resume the normal position, press the RESET key.
TITLE AREA
Adjusts the subtitle area.
Adjustable range is 0 to +7.
As the setting increases, the subtitle area becomes
wide, and as the setting decreases, the subtitle area
becomes narrow.
To resume the normal area, press the RESET key.
Note
Although the adjustable range displayed is 0 to +7, the
actual range may be limited depending on the V
SCROLL setting.
VIDEO MEMORY
Displays the selected video memory number.  There
are 6 memory settings.  If you select OFF, the image
is displayed according to the settings stored in each
channel memory.
How to set the VIDEO MEMORY
Using the Remote Commander
1Press the desired number (1 Ð 6) of the VIDEO
MEMORY keys.
The selected memory number is displayed in the
menu.
2From an appropriate menu, select an item to be
adjusted and adjust the setting using the M, m, <
or , keys.
3Press the < or ENTER key.
The adjusted item (setting) is stored in the selected
memory number.  The screen returns to the previous
screen.
.........................................................................................................................................................................................................
1) The RGB signals of a computer
Using the Control Panel
1Select a VIDEO MEMORY number (1 Ð 6) by
pressing the VIDEO MEMORY key.
(You can also set the VIDEO MEMORY with the
menu operation.)
2From an appropriate menu, select an item to be
adjusted and adjust the setting using the M, m, <
or , keys.
3Press the < or ENTER key.
The adjusted item (setting) is stored in the selected
memory number.  The screen returns to the previous
screen.
Input signals and adjustable/setting items
Item Input signal
Video or 15k RGB/HDTV/ RGB1)B&W
S video (Y/C) Progressive DTV
Component
DOT Ð ÐÐPHASE
SIZE H ÐÐ
SHIFT ÐÐ
ASPECTÐÐ
SCAN Ð Ð ÐÐ
CONV
(lower
than
SVGA
only)
VÐÐ
SCROLL
TITLE
ÐÐ
AREA
VIDEO
MEMORY
 : Adjustable/can be set
Ð : Not adjustable/can not be set
 : Aspect ratio dependent item
About the preset memory
This projector has 45 kinds of preset data for input
signals (the preset memory). When the preset signal is
input, this projector automatically detects the signal
type. When the signal is registered to the preset
memory, a suitable picture is displayed on the screen
according to the signal type. The type of input signal
is displayed in the INPUT SETTING menu. You can
adjust the preset data through the INPUT SETTING
menu.
This projector also has 20 kinds of user memories for
each INPUT-A/B. You can register a new type of
signal that is not preset. When an unpreset signal is
input for the first time, the setting via INPUT-A/B
adjusted in the INPUT SETTING menu is stored.
When more than 20 user memories are registered for
each INPUT-A/B, the newest memory is
automatically stored over the oldest one. 
						

							26 (GB)
Preset signals
Memory Preset signalfH fV SyncSIZENo.(kHz) (Hz)H
1 Video 60 Hz15.734 59.940 H-neg V-neg 1050
2 Video 50 Hz15.625 50.000 H-neg V-neg 1072
315k RGB/Component 60 Hz 15.734 59.940 1050
415k RGB/Component 50 Hz 15.625 50.000 1072
5HDTV(1080/60i) 33.750 60.000 2200
6640 ´ 350VGA mode 131.469 70.086 H-pos V-neg 800
7VGA VESA 85 Hz37.861 85.080 H-pos V-neg 832
8640 ´ 400PC-9801 Normal24.823 56.416 H-neg V-neg 848
9VGA mode 231.469 70.086 H-neg V-pos 800
10VGA VESA 85 Hz37.861 85.080 H-neg V-pos 832
11640 ´ 480VGA mode 331.469 59.940 H-neg V-neg 800
12Macintosh 13Ó35.000 66.667 SonG 864
13VGA VESA 72 Hz37.861 72.809 H-neg V-neg 832
14VGA VESA 75 Hz37.500 75.000 H-neg V-neg 840
15VGA VESA 85 Hz43.269 85.008 H-neg V-neg 832
16800 ´ 600SVGA VESA 56 Hz35.156 56.250 H-pos V-pos 1024
17SVGA VESA 60 Hz37.879 60.317 H-pos V-pos 1056
18SVGA VESA 72 Hz48.077 72.188 H-pos V-pos 1040
19SVGA VESA 75 Hz46.875 75.000 H-pos V-pos 1056
20SVGA VESA 85 Hz53.674 85.061 H-pos V-pos 1048
21832 ´ 624Macintosh 16Ó49.724 74.550 H-neg V-neg 1152
221024 ´ 768XGA VESA 43 Hz35.524 43.479 H-pos V-pos 1264
23XGA VESA 60 Hz48.363 60.004 H-neg V-neg 1344
24XGA VESA 70 Hz56.476 69.955 H-neg V-neg 1328
25XGA VESA 75 Hz60.023 75.029 H-pos V-pos 1312
26XGA VESA 85 Hz68.677 84.997 H-pos V-pos 1376
271152 ´ 864 SXGA VESA 70 Hz63.995 70.019 H-pos V-pos 1472
28SXGA VESA 75 Hz67.500 75.000 H-pos V-pos 1600
29SXGA VESA 85 Hz77.487 85.057 H-pos V-pos 1568
301152 ´ 900Sunmicro LO 61.795 65.960 H-neg V-neg 1504
31Sunmicro HI 71.713 76.047 C-neg 1472
321280 ´ 960 SXGA VESA 60 Hz60.000 60.000 H-pos V-pos 1800
33SXGA VESA 75 Hz75.000 75.000 H-pos V-pos 1728
341280 ´ 1024 SXGA VESA 43 Hz46.433 43.436 H-pos V-pos 1696
35SGI-553.316 50.062 SonG 1680
36SXGA VESA 60 Hz63.974 60.013 H-pos V-pos 1696
37SXGA VESA 75 Hz79.976 75.025 H-pos V-pos 1688
43480/60p480/60p (           ) 31.470 60.000 1050
44575/50p 575/50p (           ) 31.250 50.000 SonG/Y 1072
451080/50i 1080/50i28.130 50.000 or 2640
47720/60p 720/60p45.000 60.000 composite 1650
48720/50p 720/50p37.500 50.000 sync 1980
491)1080/24PsF 1080/24PsF27.000 48.000 2750
50HDTV 540/60p33.750 60.000 H-pos V-pos 2200
511366 ´ 76816:9 RGB 45.000 56.000 H-neg V-neg 1766
The INPUT SETTING Menu
ProgressivecomponentProgressivecomponent
After the data has been recalled from the preset
memory about the following signals, you can use
these preset data by adjusting SIZE H. Make fine
adjustment by adjusting SHIFT.
Signal Memory No. SIZE H
Super Mac-2 23 1312
SGI-1 23 1320
Macintosh 19Ó 25 1328
Macintosh 21Ó 28 1456
Sony News 36 1708
PC-9821 36 1600
1280 ´ 1024
WS Sunmicro 37 1664
Notes
¥ A part of the screen is displayed in black depending
on the aspect ratio of the input signal.
¥ Use the following signals to input the sync signal
externally from the SYNC/HD connector.
- 15k RGB signal:  Composite sync signal or
composite video signal
- Component signal(15K):  Cannot externally input
sync signal.
- Progressive component signal or DTV (Preset No.
3 Ð 5 or No. 43 Ð 48), 1080/24PsF:  Composite sync
signal
The adjustable items in the VIDEO
MEMORY
Items which can set in the VIDEO MEMORY are:
¥ ÒCONTRASTÓ, ÒBRIGHTÓ, ÒCOLORÓ, ÒHUEÓ,
ÒSHARPÓ, ÒRGB ENHANCERÓ, ÒD.PICTUREÓ,
ÒCOLOR TEMPÓ, ÒCOLOR SYSÓ and ÒDRC-MFÓ
in the PICTURE CTRL menu.
¥ ÒASPECTÓ, ÒSCAN CONVÓ,  ÒV SCROLLÓ and
ÒTITLE AREAÓ in the INPUT SETTING menu.
.........................................................................................................................................................................................................
1) No. 49 is an interlace signal.
SonG/Y or
composite sync
SonG/Y or
composite sync
SonG/Y or composite
sync/composite video 
						

							27 (GB)
The SET SETTING Menu
The SET SETTING menu is used for changing the
settings of the projector.
STATUS (on-screen display)
Sets up the on-screen display.
ON: Shows all of the on-screen displays.
OFF: Turns off the on-screen displays except for the
menus, a message when turning off the power,
and warning messages.
INPUT-A
Selects the computer, component, DTV YPBPR or
DTV GBR signal input from the INPUT A
connectors.
Note
If the setting is not correct, ÒPlease check INPUT-A
setting.Ó appears on the screen and the color of the
picture becomes strange or the picture is not
displayed.
INPUT-B
Selects the computer, component, DTV YPBPR or
DTV GBR signal input from the INPUT-B
connectors.
Notes
¥ If the setting is not correct, ÒPlease check INPUT-B
setting.Ó appears on the screen and the color of the
picture becomes strange or the picture is not
displayed.
¥ Set the progressive component signal, e.g. DVD, to
ÒCOMPONENTÓ; 15k RGB signal, e.g. game
machines, to ÒDTV GBR.Ó
SET SETTING
STATUS: ON
INPUT-A: COMPONENT
INPUT-B: COMPONENT
LANGUAGE: ENGLISH
POWER SAVING:OFFSIRCS RECEIVER:FRONT&REARCINE MOTION:AUTOINPUT-A
The SET SETTING Menu
The signals that can be output for each setting of
INPUT-A and -B are as shown below.
Setting of INPUT -A and -BSignalCOMPUTERCOMPONENTDTV YPBPRDTV GBR
15k RGB Ð Ð Ð(DVD output inPAL system, etc.)
Component ÐÐ
ProgressiveÐÐComponent
(Progressive
DVD output etc.)
DTV (Digital BSÐÐ output, etc.)
ComputerÐÐÐ
 : can be output Ð : cannot be output
LANGUAGE
Selects the language used in the menu and on-screen
displays.
Available languages are: English, French, German,
Italian, Spanish, Japanese and Chinese.
POWER SAVING
When set to ON, the projector goes into the power
saving mode if no signal is input for 10 minutes.
The power saving mode is canceled when a signal is
input or any key is pressed.
SIRCS RECEIVER
Selects the remote control detectors (SIRCS receiver)
on the front and rear of the projector.
FRONT & REAR: Activates both the front and rear
detectors.
FRONT: Activates the front detector only.
REAR: Activates the rear detector only.
CINE MOTION
Selects either position according to the signal source
for the NTSC
3.58/4.43, 15k RGB (60 Hz) or 525/60
signal.
AUTO: Set to AUTO when the input signal is from
a film-originated material.  2-3 pull down is
applied.
OFF: 2-3 pull down is not applied.
Note
This function will not operate for signals of 50Hz. 
						

							28 (GB)
The INSTALL SETTING
Menu
The INSTALL SETTING menu is used for changing
the settings of the projector.
KEYSTONE MEM
ON: DIGIT KEYSTONE setting is stored.
The data is retrieved when the projector power is
turned on. The setting will remain the same every
time.
OFF: DIGIT KEYSTONE is reset to 0 when the
power is turned on the next time.
DIGIT KEYSTONE
Corrects the trapezoid caused by the projection angle.
If the base edge is longer,  set a negative value; if the
upper edge is longer, set a positive value to square the
image.
Note
If ÒZOOMÓ, ÒFULLÓ or ÒNORMALÓ have been
selected in the ASPECT of the INPUT SETTING, you
can change the trapezoid.
The INSTALL SETTING Menu
INSTALL SETTING
KEYSTONE MEM:OFFDIGIT KEYSTONE:0INSTALLATION:FLOOR-FRONTCINEMA BLACK:ON
LAMP TIMER: 234hINPUT-A
INSTALLATION
Sets to reverse the picture horizontally or vertically.
FLOOR-FRONT: The picture is not reversed.
CEILING-FRONT: The picture is reversed
horizontally and vertically.
FLOOR-REAR: The picture is reversed
horizontally.
CEILING-REAR: The picture is reversed
vertically.
Note
In case of using a mirror, be careful of installation
since the picture may be reversed.
CINEMA BLACK
Switches the lamp wattage during projection.
OFF: Normal wattage.
ON: Enhances the black by reducing the lamp
wattage.
Notes
¥ It will take a few seconds for the projector to change
the lamp wattage during projection.
¥ If the CINEMA BLACK is set to ON, it starts with
OFF when the power is turned on, then changes to
ON after a while.
LAMP TIMER
Indicates how long the lamp has been turned on.
Note
This only displays the time.  You cannot alter the
display. 
						

							29 (GB)
a: Distance between the screen and the center of the lens
b: Distance from the floor to the center of the lens
c: Distance from the floor to the foot of the projector
x: Free
16:9 Screen size (inches) 40 60 80 100 120 150 180 200 250 300
Minimum1260 1930 2600 3270 3930 4940 5940 6610 8270 9940
       a(49 5/8) (76) (102 3/8) (128 7/8) (154 3/4) (194 5/8) (234) (260 3/8) (325 3/4) (391 1/2)
Maximum1470 2240 3010 3780 4550 5710 6860 7630 9560 11480
(58) (88 1/4) (118 5/32) (148 7/8) (179 1/4) (224 7/8) (270 1/8) (300 1/2) (376 1/2) (452 1/8)
                     bxÐ249 xÐ374 xÐ498 xÐ623 xÐ747 xÐ934 xÐ1121 xÐ1245 xÐ1556 xÐ1868
(9 7/8) (14 3/4) (19 5/8) (24 5/8) (29 1/2) (36 7/8) (44 1/8) (49 1/8) (61 3/8) (73 5/8)
                     cxÐ349 xÐ473 xÐ598 xÐ722 xÐ847 xÐ1033 xÐ1220 xÐ1345 xÐ1656 xÐ1967
(13 3/4) (18 5/8) (23 5/8) (28 1/2) (33 3/8) (40 3/4) (48 1/8) (53) (65 1/4) (77 1/2)
Unit: mm (inches)
To calculate the installation measurement (unit: mm)
SS: screen size diagonal (inches)
a (minimum) = {(SS ´ 44.22/1.3573) Ð 70.76208} ´ 1.025
a (maximum) = {(SS ´ 53.599173/1.3573) Ð 70.17171} ´ 0.975
Installation Examples
Floor Installation
Installation Examples
Installation
4:3 Screen size (inches) 40 60 80 100 120 150 180 200 250 300
Minimum1560 2380 3200 4020 4830 6060 7290 8100 10150 12190
       a(61 1/2) (93 3/4) (126) (158 5/16) (190 1/4) (238 5/8) (287 1/8) (319) (399 3/4) (480)
Maximum1820 2760 3700 4650 5590 7000 8420 9360 11720 14070
(71 3/4) (108 3/4) (145 3/4) (183 1/8) (220 1/8) (275 5/8) (331 5/8) (368 5/8) (461 1/2) (554 1/8)
                     bxÐ305 xÐ457 xÐ610 xÐ762 xÐ915 xÐ1143 xÐ1372 xÐ1524 xÐ1905 xÐ2287
(12) (18 1/8) (24 1/8) (30 1/8) (36 1/8) (45 1/8) (54 1/8) (60 1/8) (75 1/8) (90 1/8)
                     cxÐ404 xÐ557 xÐ709 xÐ862 xÐ1014 xÐ1243 xÐ1471 xÐ1624 xÐ2005 xÐ2386
(16) (22) (28) (34) (40) (49) (58) (64) (78 31/32) (94)
 



a x
b
c
Distance from the front of the
cabinet and the center of the lens
Standard lens: 10 mm (
13/32 inches) Center of the lens Center of the screen Wall
Floor
To calculate the installation measurement (unit: mm)
SS: screen size diagonal (inches)
a (minimum) = {(SS ´ 44.22/1.1087) Ð 70.76208} ´ 1.025
a (maximum) = {(SS ´ 53.597384/1.1087) Ð 70.27214} ´ 0.975b = x Ð (SS/1.3573 ´ 8.45)
c = x Ð (SS/1.3573´ 8.45 + 99.5)
Unit: mm (inches)
b = x Ð (SS/1.1087 ´ 8.45)
c = x Ð (SS/1.1087 ´ 8.45 + 99.5)
Installation 
						

							30 (GB)
Ceiling Installation
When installing the projector on the ceiling, use the
PSS-610 Projector Suspension Support.
a: Distance between the screen and the center of the lens
b: Distance between the ceiling and the center of the lens
x: Distance between the ceiling and the center of the screen
16:9 Screen size (inches) 80 100 120 150 180 200 250 300
Minimum2600 3270 3930 4940 5940 6610 8270 9940
      a(102 3/8) (128 7/8) (154 3/4) (194 5/8) (234) (260 3/8) (325 3/4) (391 1/2)
Maximum3010 3780 4550 5710 6860 7630 9560 11480
(118 5/32) (148 7/8) (179 1/4) (224 7/8) (270 1/8) (300 1/2) (376 1/2) (452 1/8)
                    
xb+498 b+623 b+747 b+934 b+1121 b+1245 b+1556 b+1868(19 5/8) (24 5/8) (29 1/2) (36 7/8) (44 1/8) (49 1/8) (61 3/8) (73 5/8)
                    b247/272/297/347/372/397 mm (9 3/4/10 3/4/11 3/4/13 3/4/14 3/4/15 3/4 inches) adjustable when using PSS-610
PSS-610 Projector Suspension Support
(not supplied)
Unit: mm (inches)
For ceiling installation, consult with qualified Sony
personnel.
To calculate the installation measurement (unit: mm)
SS: screen size diagonal (inches)
a (minimum) = {(SS ´ 44.22/1.3573) Ð 70.76208} ´ 1.025
a (maximum) = {(SS ´ 53.599173/1.3573) Ð 70.17171} ´ 0.975
x = b + (SS/1.3573 ´ 8.45)
Installation Examples
4:3 Screen size (inches) 80 100 120 150 180 200 250 300
Minimum3200 4020 4830 6060 7290 8100 10150 12190
      a(126) (158 5/16) (190 1/4) (238 5/8) (287 1/8) (319) (399 3/4) (480)
Maximum3700 4650 5590 7000 8420 9360 11720 14070
(145 3/4) (183 1/8) (220 1/8) (275 5/8) (331 5/8) (368 5/8) (461 1/2) (554 1/8)
                    
xb+610 b+762 b+915 b+1143 b+1372 b+1524 b+1905 b+2287(24 1/8) (30 1/8) (36 1/8) (45 1/8) (54 1/8) (60 1/8) (75 1/8) (90 1/8)
                    b247/272/297/347/372/397 mm (9 3/4/10 3/4/11 3/4/13 3/4/14 3/4/15 3/4 inches) adjustable when using PSS-610
 



a
xb
Center of the lensCeiling
Center of the screen
Distance from the front of the
cabinet and the center of the
lens
Standard lens:
10 mm (
13/32 inches)
To calculate the installation measurement (unit: mm)
SS: screen size diagonal (inches)
a (minimum) = {(SS ´ 44.22/1.1087) Ð 70.76208} ´ 1.025
a (maximum) = {(SS ´ 53.597384/1.1087) Ð 70.27214} ´ 0.975
x = b + (SS/1.1087 ´ 8.45)
Unit: mm (inches)