Sony Projector Vpl Vw10ht User Manual

							11 (GB)
Location and Function of Controls
Control panel
1 I / 1 (on / standby) key
Turns the projector on and off when the projector is in
the standby mode. The ON/STANDBY indicator
lights in green when the power is turned on.
When turning off the power, press the I / 
1 key
twice following the message on the screen, or press
and hold the key for about one second.
For details on steps for turning off the power, see “To turn
off the power” on page 20 (GB).
2 INPUT key
Selects the input signal. Each time you press the key,
the input signal switches as follows:
3 VIDEO MEMORY key
You can adjust the image in advance and store the
setting in the VIDEO MEMORY 1 to 6.  You can
recall the setting by pressing this key. Pressing this
key selects memory number 1 through 6, and then
starts again with 1. You can easily set, change and
view the image in a suitable setting.
For more details on how to set the video memory, see the
VIDEO MEMORY of the INPUT SETTING menu on page
25 (GB).
4 LIGHT key
If you press this key while the power is on, the keys
on the control panel will be displayed in orange.
Press this key again to turn off the light.
The light will turn off automatically if no keys are
operated for 30 seconds.
5 PATTERN key
Displays the test pattern on the screen for focus
adjustment. Press again to clear the test pattern.
6 RESET key
Resets the value of an item back to its factory preset
value. This key functions when the menu or a setting
item is displayed on the screen.7 ENTER key
Enters the settings of items in the menu system.
8 MENU key
Displays the on-screen menu. Press again to clear the
menu.
9 Arrow keys (M/m/
						

							12 (GB)
Connector panel
1 INPUT A connectors
G/Y, B/C
B/PB, R/CR/PR, SYNC/HD, VD connectors
(phono type):
Connect to the RGB output of the equipment.
According to the connected equipment, computer,
component (Y/C
B/CR),  HDTV or DTV (DTV GBR,
DTV YP
BPR) signal is selected.
2 INPUT B connectors
G/Y, B/C
B/PB, R/CR/PR, SYNC/HD, VD connectors
(phono type):
Connect to the RGB output of the equipment.
According to the connected equipment, computer,
component (Y/C
B/CR),  HDTV or DTV (DTV GBR,
DTV YP
BPR) signal is selected.
3 RS-232C connector (D-sub 9-pin, female)
This is a service connector.
4 TRIGGER connector (minijack)
Outputs the ON or OFF condition of the unit to the
external equipment.
When the unit is turned off, 0 V is output and when
the unit is turned on, 12 V is output. However, as
power is not output, you cannot use the connector as a
power source.
5 CONTROL S IN/PLUG IN POWER (DC 5V
output) jack
Connects to the control S out jacks of the Sony equipment.
Connects to the CONTROL S OUT jack on the supplied
Remote Commander when using it as a wired Remote
Commander. In this case, you do not need to install the
batteries in the Remote Commander, since power is
supplied from this jack.
If this connector is used, the Remote Commander key
lamp is not turned on.
Left side
Location and Function of Controls
CONTROL S IN VIDEO IN
TRIGGER
REMOTEINPUT A
INPUT  B
PLUG IN POWER
RS-232C
(FOR SERVICE USE)S VIDEO
G/Y B/C
B/PBR/CR/PRSYNC/HD VD VIDEO
G/Y B/CB/PBR/CR/PRSYNC/HD VD
1
2 3 456
6 VIDEO IN jacks
Connect to external video equipment such as a VCR.
S VIDEO (mini DIN 4-pin): 
Connects to the S video
output (Y/C video output) of video equipment.
VIDEO (phono type): Connects to the composite
video output of video equipment. 
						

							13 (GB)
Remote Commander
The keys which have the same names as on the
control panel function identically.
You can control a connected computer using the
Remote Commander.
For details, see “Connecting with a Computer” on page
16 (GB).
1 I (ON) key
Press this key to turn on the projector.  (It is assumed
that the projector is in the Stand-by state.)
2 
1 (OFF) key
Press this key to turn off the power immediately.
3 INPUT SELECT keys
Select the input signal.
VIDEO: Selects the signal of equipment connected
to the projector’s VIDEO connector.
S VIDEO: Selects the signal of equipment
connected to the projector’s S VIDEO connector.
A: Selects the video signal of equipment connected
to the INPUT A connectors.
B: Selects the video signal of equipment connected
to the INPUT B connectors.
Location and Function of Controls
4 VIDEO MEMORY keys
You can store an image setting to one of the VIDEO
MEMORY keys (1 – 6), and you can directly recall
the setting by pressing the appropriate key.
For more details on how to set the video memory, see the
VIDEO MEMORY of the INPUT SETTING menu on page
25 (GB).
5 MENU key
6 ENTER key
7 RESET key
8 Arrow keys (M/m/
						

							14 (GB)
Location and Function of Controls / Installing the Projector
Be sure to
install the
battery from
the # side.
Battery installation
1Push and slide to open the lid, then install the two
size AA (R6) batteries (supplied) with the correct
polarity.
2Replace the lid.
Notes on batteries
• Make sure that the battery orientation is correct when
inserting batteries.
• Do not mix an old battery with a new one, or
different types of batteries.
• If you will not use the Remote Commander for a
long time, remove the batteries to avoid damage
from battery leakage. If batteries have leaked,
remove them, wipe the battery compartment dry and
replace the batteries with new ones.
Notes on Remote Commander operation
• Make sure that there is nothing to obstruct the
infrared beam between the Remote Commander and
the remote control detector on the projector.
• The operation range is limited. The shorter the
distance between the Remote Commander and the
projector is, the wider the angle within which the
commander can control the projector.
• To turn on the key light when using as a wired
Remote Commander, install the batteries.
Note
When the Remote Commander causes malfunction,
consult with qualified Sony personnel. We change the
Remote Commander as new one according to the
guarantee.
Installing the Projector
This section describes the installation arrangements
for installing the projector.
The distance between the lens and the screen varies
depending on the size of the screen.
Use the following table as a guide.
Unit: m (feet)
16:9
screen
size40 60 80 100 120 150 200 300
(inches)
Minimum 1.3 1.9 2.6 3.3 3.9 4.9 6.6 9.9
Distance (4.1) (6.3) (8.5) (10.7) (12.9) (16.2) (21.7) (32.6)
Maximum 1.5 2.2 3.0 3.8 4.6 5.7 7.6 11.5Distance (4.8) (7.4) (9.8) (12.4) (14.9) (18.7) (25.0) (37.7)Distance between the screen
and the center of the lens
 


4:3
screen
size40 60 80 100 120 150 200 300
(inches)
Minimum 1.6 2.4 3.2 4.0 4.8 6.1 8.1 12.2
Distance (5.1) (7.8) (10.5) (13.2) (15.9) (19.9) (26.6) (40.0)
Maximum 1.8 2.8 3.7 4.7 5.6 7.0 9.4 14.1Distance (6.0) (9.1) (12.3) (15.4) (18.3) (23.0) (30.8) (46.2) 
						

							15 (GB)
Connecting
When making connections, be sure to:
•
turn off all equipment before making any connections.
•use the proper cables for each connection.
•insert the plugs of the cables properly; plugs that are
not fully inserted often generate noise. When pulling
out a cable, be sure to pull it out by the plug, not the
cable itself.
Connecting with a VCR/15k RGB/
Component/Progressive
Component Equipment
This section describes how to connect the projector
with a VCR, external active speakers, and 15k RGB/
component/progressive component equipment.
Also refer to the instruction manuals of the equipment
to be connected.
Connecting
Setting up and projecting
Left side
CONTROL S IN VIDEO IN
TRIGGER
REMOTEINPUT A
INPUT  B
PLUG IN POWER
RS-232C
(FOR SERVICE USE)S VIDEO
G/Y B/C
B/PBR/CR/PRSYNC/HD VD VIDEO
G/Y B/CB/PBR/CR/PRSYNC/HD VD
S-Video cable
 (not supplied)Video cable
(not supplied)
Active speakers
to video
output to S video
output
VCRLeft side
CONTROL S IN VIDEO IN
TRIGGER
REMOTEINPUT A
INPUT  B
PLUG IN POWER
RS-232C
(FOR SERVICE USE)S VIDEO
G/Y B/C
B/PBR/CR/PRSYNC/HD VD VIDEO
G/Y B/CB/PBR/CR/PRSYNC/HD VD
15k RGB/Component equipment to RGB/
component/
progressive
component
outputPin Cable
(not
supplied)
Active speakers
Notes
•Set the aspect ratio using ASPECT in the INPUT
SETTING menu according to the input signal.
•To connect a 15k RGB/component/progressive
component equipment, select the COMPUTER/
COMPONENT/DTV YP
BPR/DTV GBR in the
INPUT-A or INPUT-B in the SET SETTING menu
according to the input signal.
For details on setting, see page 27 (GB).
•Use the composite sync signal when you input the
external sync signal from 15k RGB/component
equipment.
•You can connect a high definition equipment. The
connection method is the same as above.
Connecting to an HDTV 1035/60i
Set the input setting to “DTV YP
BPR/DTV GBR.”
Use the composite sync signal when you input the
external sync signal. 
						

							16 (GB)
CONTROL S IN VIDEO IN
TRIGGER
REMOTEINPUT A
INPUT  B
PLUG IN POWER
RS-232C
(FOR SERVICE USE)S VIDEO
G/Y B/C
B/PBR/CR/PRSYNC/HD VD VIDEO
G/Y B/CB/PBR/CR/PRSYNC/HD VD
Connecting
Connecting with a Computer
This section describes how to connect the projector to
a computer.
Select the “COMPUTER” in the INPUT-A or
INPUT-B of the SET SETTING menu.
Notes
•This unit accepts the VGA, SVGA, XGA or SXGA
signals. However, we recommend you to set the
output signal of your computer to the XGA.
•If you set your computer, such as a notebook type
IBM PC/AT compatible, to output the signal to both
the display of your computer and the external
monitor, the picture of the external monitor may not
appear properly. In such cases, set the output mode
of your computer to output the signal only to the
external monitor.
For details, refer to the operating instructions supplied
with your computer.
•Connect all the connecting cables to the INPUT A
connector when you input a signal from the INPUT
A connector.
Connect all the connecting cables to the INPUT B
connector when you input a signal from the INPUT
B connector as well.
When connecting with a computer
Note
When you connect with a Macintosh computer, you
need an optional signal adapter.
Left side
to
monitor
out
ComputerMonitor
cable
SMF-400
(not
supplied)
Speakers
.............................................................................................
1) When connecting INPUT A or INPUT B connectors
on the projector, you need conversion plugs.
Conversion plugs1) 
						

							17 (GB)
Selecting the Menu Language
Selecting the Menu Language
You can select the language for displaying in the
menu and other on screen display. The factory setting
is ENGLISH.
1Plug the AC power cord into the wall outlet.
2Press the I / 1 key to turn on the power.
3Press the MENU key.
The menu display appears.
4Select the icon of SET SETTING Menu, the third
one, by using the M or m key, then press the , or
ENTER key.
 The SET SETTING Menu appears.
LAMP/
COVERTEMP/
 FANPOWER
SAVINGON/
STANDBY
MENU
LIGHTVIDEO MEMORYENTER
PATTERN
RESET
INPUT
2 4, 5, 6
3
1
5Select LANGUAGE with the M or m key, then
press the , or ENTER key.
6Select the language desired with the M or m key,
then press the < or ENTER key.
The menu changes into the selected language .
To clear the menu display
Press the MENU key.
The menu display disappears automatically if no key
is pressed for one minute.
SET SETTING
STATUS: ON
INPUT-A: COMPONENT
INPUT-B: COMPONENT
LANGUAGE: ENGLISH
POWER SAVING:OFFSIRCS RECEIVER:FRONT&REARINPUT-A
PICTURE CTRL
CONTRAST: 80
BRIGHT: 50
RGB ENHANCER:30
COLOR TEMP: LOWINPUT-A
SET SETTINGINPUT-A
STATUS: ON
INPUT-A: COMPONENT
INPUT-B:
LANGUAGE:
POWER SAVING:SIRCS RECEIVER:
ENGLISH
FRANCAIS
DEUTSCH
ITALIANO
ESPANOL 
						

							18 (GB)
Projecting
4Press the INPUT key to select the input source.
INPUT-A:Selects video signal input from the INPUT
A  connector, such as component
equipment.
INPUT-B:Selects video signal input from the INPUT
B  connector, such as component
equipment.
VIDEO:Selects video signal input from the VIDEO
(VIDEO IN) jack.
S-VIDEO:Selects video signal input from the S
VIDEO (VIDEO IN) jack.
5Press the PATTERN key on the control panel to
display the test pattern, and turn the focus ring to
adjust the focus.
Press the PATTERN key again to clear the test
pattern.
6Turn the zoom ring to adjust the size of the
picture.
Note
Looking into the lens when projecting may cause
injury to your eyes.
To Press
Cut off the picturethe MUTING PIC key on the remote
commander. To restore the picture,
press the MUTING PIC key again.
1After all equipment is completely connected, plug
the AC power cord into the wall outlet.
The ON/STANDBY indicator lights in red and the
projector goes into the standby mode.
2Press the I / 1 key on the control panel or
the I key on the Remote Commander.
The ON/STANDBY indicator lights in green.
3Turn on equipment connected to the projector.
Projecting
LAMP/
COVERTEMP/
 FANPOWER
SAVINGON/
STANDBY
MENU
LIGHTVIDEO MEMORYENTER
PATTERN
RESET
INPUT
MUTING
INPUT SELECT
VIDEO MEMORY PICVIDEO
S VIDEOA
123
4
OFF
MENU
ENTERRESET
56B
2
4
1 5,65
2
4 
						

							19 (GB)
Projecting
To correct the trapezoid
When the projecting image is a trapezoid, change the
projector’s position/height by moving the adjuster.
For details on “How to use the adjuster”, see page 10 (GB).
If the image is still a trapezoid, correct it in DIGIT
KEYSTONE in the INSTALL SETTING menu.
When the base edge is longer than the upper
edge as shown in the figure below:
When the upper edge is longer than the base
edge as shown in the figure below:
Note
If “ZOOM”, “FULL” or “NORMAL” have been
selected in the ASPECT of the INPUT SETTING
menu, you can change the trapezoid.
For details on “DIGIT KEYSTONE”, see page 28 (GB).
Changing the aspect
You can change the aspect according to the video
signal. For details on the menu screen operation, see
“Using the Menu” on page 21 (GB).
1Press the MENU key to display the menu.
2Press the M or m key to select INPUT SETTING
menu, then press the , or ENTER key.
3Press the M or m key to select ASPECT, then
press the , or ENTER key.
Set the value to negative.
Set the value to positive.
4Make setting or adjustment on an item.
For details on setting individual items, see page 24 (GB).
The picture size for the screen size
Refer to the following for selecting the aspect.
When the 4:3 picture is displayed on the 16:9
screen
Example: The 120 inch screen is used.
The 98 inch picture is displayed1,992 2,656
1,494
16:9 screen 4:3 picture
Unit (mm) Unit (mm)
90 73
110 90
120 98
Size
(Inch)
2,656
1,494
1,494 1,992 2,435
1,370
1,370 1,826 1,121 1,992
1,121 1,494
Size
(Inch)
INPUT SETTINGVIDEO
ASPECT:VIDEO MEMORY:
VIDEO/60FULL
FULL THROUGH
NORMAL
NORMAL THROUGHZOOM
SUBTITLE
WIDE ZOOM 
						

							20 (GB)
When the 16 : 9 picture is displayed on the
4 : 3 screen
Example: The 120 inch screen is used.
4:3 screen 16:9 picture
Unit (mm) Unit (mm)
80 73
100 91
120 110
2,438
1,829
1,371
2,438 2,032
1,524
1,143
2,032 1,219 1,626
914.6
1,626
1,829 1,371
The 110 inch picture is displayed.
Size
(Inch) Size
(Inch)
To turn off the power
To turn off the power from the control panel
1Press the I / 1 key on the control panel.
“Power OFF?” appears on the screen.
Note
The message will disappear if you press any key
except the I / 
1 key, or if you do not press any
key for five seconds.
2Press the I / 1 key.
The ON/STANDBY indicator flashes in green and
the fan continues to run for about 120 seconds to
reduce the internal heat. Also, the ON/STANDBY
indicator flashes quickly for the first 40 seconds.
During this time, you will not be able to turn the
power back on with the I / 
1 key.
3Unplug the AC power cord from the wall outlet
after the fan stops running and the ON/STANDBY
indicator lights in red.
When you cannot confirm the on-screen
message
When you cannot confirm the on-screen message in a
certain condition, you can turn off the power by
holding the I / 
1 key for about one second.
To turn off the power from the Remote
Commander
1Press the 1 key on the Remote Commander.
2Unplug the AC power cord from the wall outlet
after the fan stops running and the ON/STANDBY
indicator lights in red.
Note
Do not unplug the AC power cord while the
fan is still running; otherwise, the fan will
stop although the internal heat is still high,
leading to breakdown of the projector.
About the air filter cleaning
Clean the air filter every 300 hours to ensure
optimal performance.
Notes on changing the aspect
This projector provides you with the various choices
of aspects. When changing the aspect, check the
following:
•Select an aspect taking into account that one which
changes the aspect ratio of the original picture will
provide a different look from that of the original
image.
•Also note that if the projector is used for profit or for
public viewing, modifying the original picture by
switching aspects may constitute an infringement of
the rights of authors or producers which are legally
protected by laws.
2,438
Projecting