Sanyo Projector Plv 60 User Manual

21
KEYSTONE ADJUSTMENT
1Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING Menu (P36).  The message “Keystone” is
displayed.
2Correct keystone distortion by pressing POINT UP/DOWN
button(s).  Press POINT UP button to reduce upper part of the
image, and press POINT DOWN button to reduce lower part of
the image.
To reset Keystone adjustment, press NORMAL button.
Message disappears after 4 seconds.
Reduce the upper width with POINT UP button.   Reduce the lower width with POINT DOWN...

22
MUTE SETTING
VOLUME ADJUSTMENT
BASIC OPERATION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button.
Press NO SHOW button on Remote Control Unit to black out the
image.  To restore to normal, press NO SHOW button again or press
any other button.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
Message disappears after 4 seconds.
No show
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to...

23
COMPUTER MODE
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose either Input 1 or Input 2 by pressing INPUT button on Top
Control or on Remote Control Unit.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button to move a red arrow pointer to
either Input 1 or Input 2 that you want to choose and then press
SELECT button.
When choosing Input 2, Source Select Menu will appear.  Move
POINTER to...

PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync., Total dots, and Picture Position to conform to
your computer.  Auto PC Adjustment function can be operated as follows.
NOTE : Auto PC Adjustment function cannot be operated when
“RGB,” “HDTV720p,” “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1...

25
COMPUTER MODE
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals from most personal computers currently distributed.  However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector.  If this happens, projector cannot reproduce a proper image and the image may be recognized
as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This...

26
COMPUTER MODE
NOTE : Display area (H/V), Horizontal scale and Vertical scale
cannot be adjusted when “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Fine sync and Total dots cannot be fully adjusted when
“HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu
(P23, 24).
Selects area displayed with this projector.  Select the resolution at
the Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) and adjust...

27
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and
less than 180 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x...

28
COMPUTER MODE
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
level that you want to set and then press SELECT button.
Move the red frame icon to the
level and press SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture level preset on this projector.
Standard
Picture level adjusted...

29
COMPUTER MODE
Press POINT LEFT/RIGHT buttons
to adjust value.
Reset all adjustment to previous figure.
Reset
Stored
Closes IMAGE MENU.
Quit
Other icons operates as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust. and then press SELECT button.
The level of each item is displayed.  Adjust each level by
pressing POINT...

30
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
Adjusts image size or pans image.  In “Digital Zoom” mode, the ON-
SCREEN MENU disappears and the magnifying glass icon and the
message “D. Zoom” is displayed.  
This projector also enters Digital Zoom mode by pressing the...