Sanyo Projector Plv 60 User Manual

							21
KEYSTONE ADJUSTMENT
1Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING Menu (P36).  The message “Keystone” is
displayed.
2Correct keystone distortion by pressing POINT UP/DOWN
button(s).  Press POINT UP button to reduce upper part of the
image, and press POINT DOWN button to reduce lower part of
the image.
To reset Keystone adjustment, press NORMAL button.
Message disappears after 4 seconds.
Reduce the upper width with POINT UP button.   Reduce the lower width with POINT DOWN button.  
Keystone
If image has keystone distortion, correct image with KEYSTONE adjustment.
BASIC OPERATION
ADJUSTING SCREEN
Message disappears after 4 seconds.
Message disappears after 4 seconds.
Zoom
Focus
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
Message disappears after 4 seconds.
Lens shift
LENS SHIFT ADJUSTMENT
1Press LENS SHIFT /button(s) on Top Control or LENS
SHIFT button on Remote Control Unit.  The message “Lens
shift” is displayed.
2Press LENS SHIFT button or POINT UP button to move
image up, and press LENS SHIFT button or POINT DOWN
button to move image down.
Refer to P9 for operating range.
1Press ZOOM /button(s) on Top Control or on Remote
Control Unit.  The message “Zoom” is displayed.
2Press ZOOM button or POINT UP button to make image
larger, and press ZOOM button or POINT DOWN button to
make image smaller.
1Press FOCUS /button(s) on Top Control or on Remote
Control Unit.  The message “Focus” is displayed.
2Adjust focus of the image by pressing FOCUS /button(s) or
POINT UP/DOWN button(s) . 
						

							22
MUTE SETTING
VOLUME ADJUSTMENT
BASIC OPERATION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button.
Press NO SHOW button on Remote Control Unit to black out the
image.  To restore to normal, press NO SHOW button again or press
any other button.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
Message disappears after 4 seconds.
No show
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears on the screen for a
few seconds.
(+) button to increase volume, and (–) button decreasing.
Press MUTE button on Remote Control Unit to cut off  sound.  To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Indicates the roughly level
of volume.
Press MUTE button to set
Mute function On or Off.
The display disappears after 4 seconds.  
SOUND ADJUSTMENT 
						

							23
COMPUTER MODE
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose either Input 1 or Input 2 by pressing INPUT button on Top
Control or on Remote Control Unit.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button to move a red arrow pointer to
either Input 1 or Input 2 that you want to choose and then press
SELECT button.
When choosing Input 2, Source Select Menu will appear.  Move
POINTER to RGB and then press SELECT button.  (Input 2
accepts R, G, B, H/V and V computer signals (P 13).)
1
2
INPUT button
Input 1
Input 2
Input 3
Move POINTER (red arrow)
to Input 1 or 2 and press
SELECT button.
INPUT 2
Move POINTER to RGB and
press SELECT button.
Source Select Menu (Input 2)
INPUT MENU
INPUT Menu icon
SELECTING COMPUTER SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 27).  When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting.  (Some computers need setting manually.)
Note : Projector may display one of the following messages.
When projector cannot recognize connected signal
as PC system provided in this projector, Auto PC
Adjustment function operates to adjust projector
and the message “AUTO PC Adj.” is displayed on
SYSTEM icon.  When image is not provided
properly, manual adjustment is required.  (Refer to
P25 and 26.)
There is no signal input from computer.  Make
sure the connection of computer and projector is
set correctly.  
(Refer to TROUBLESHOOTING on page 40.)
AUTO PC Adj.
No signal
SYSTEM Menu icon
Displays system being
selected.
SYSTEM MENU 
						

							PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync., Total dots, and Picture Position to conform to
your computer.  Auto PC Adjustment function can be operated as follows.
NOTE : Auto PC Adjustment function cannot be operated when
“RGB,” “HDTV720p,” “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button.
This Auto PC Adjustment can be executed by pressing AUTO
PC ADJ. button on Top Control or on Remote Control Unit.
Move a red frame pointer to AUTO PC
Adj. icon and press SELECT button.
PC ADJUST MENU
Fine sync, Total dots and Picture Position of some computers
may not be fully adjusted with Auto PC Adjustment function.
When the image is not provided properly through this function,
manual adjustment is required.  (Refer to page 25, 26.)
Auto PC Adj.
PC ADJUST
Menu icon
24
COMPUTER MODE
SELECT COMPUTER SYSTEM MANUALLY
SYSTEM Menu icon 
Displays system being selected.
The systems on this dialog box
can be selected.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SYSTEM icon.
Press POINT DOWN button to move a red arrow pointer to the
system that you want to set, and then press 
SELECT button.  
1
2
When this mark is displayed as
black, more computer system
modes will be available.  Move
the arrow to this mark and then
press SELECT  button, and the
other modes will be displayed.
SYSTEM MENU
Custom Mode (1~5) set in PC
ADJUST Menu.  (P25, 26)
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector.  Once parameters are memorized, setting can be
done just by selecting Mode in SYSTEM Menu (above).  Refer to step
3 of MANUAL PC ADJUSTMENT section (P26). 
						

							25
COMPUTER MODE
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals from most personal computers currently distributed.  However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector.  If this happens, projector cannot reproduce a proper image and the image may be recognized
as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats.  This projector has 5 independent memory areas to memorize those parameters manually adjusted.  This
enables you to recall the setting for a specific computer whenever you use it. 
Note : This PC ADJUST Menu cannot be operated when “RGB” is selected on SYSTEM Menu (P23, 24).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear.  Press POINT LEFT/RIGHT
button to adjust the value.
Move the red frame icon to the item and
press SELECT button.
PC ADJUST MENU
PC ADJUST
Menu icon
Adjust the picture as necessary to eliminate flicker from the display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 255.)
Fine sync
The number of total dots in one horizontal period.  Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Total dots
Adjust horizontal picture position.  Press POINT LEFT/RIGHT
button(s) to adjust the position.
Horizontal
Adjust vertical picture position.  Press POINT LEFT/RIGHT button(s)
to adjust the position.
Vertical
Press SELECT button to show the information of computer selected.
Current mode
The number of the total horizontal lines.  Press POINT LEFT/RIGHT
button(s) and adjust number to match your PC image.
Total lines
Adjusts clamp level.  When the image has a dark bar(s), try this
adjustment.
Clamp
Press SELECT button at this icon to
adjust “Total lines,” “Clamp,” “Display
area,” “Horiz. scale” or “Vert. scale” .
Press POINT LEFT/RIGHT
button to adjust the value.
Press SELECT button at
Current mode icon to show
the information of computer
connected.Shows the status
(Stored/Free) of
Mode. Selected Mode 
						

							26
COMPUTER MODE
NOTE : Display area (H/V), Horizontal scale and Vertical scale
cannot be adjusted when “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Fine sync and Total dots cannot be fully adjusted when
“HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu
(P23, 24).
Selects area displayed with this projector.  Select the resolution at
the Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) and adjust number to match the
resolution of image.
Display area H
Adjustment of vertical area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) and adjust number to match the
resolution of image.
Display area V
Adjustment of width of image.  Press POINT LEFT/RIGHT button(s)
for adjustments.
Horizontal scale
Adjustment of height of image.  Press POINT LEFT/RIGHT button(s)
for adjustments.
Vertical scale
Press SELECT button at
Display area icon and
the Display area dialog
box appears.
Reset
Stored
Closes PC ADJUST MENU.
Quit
Other icons operates as follows.
3
To store adjustment parameters, move a red frame pointer to
Stored icon and then press SELECT button.  Move a red arrow
pointer to any of Mode 1 to 5 that you want to store to and then
press SELECT button.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Mode free
This Mode has parameters being stored.
Vacant Mode Shows values of “Fine sync,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Stored icon
Mode free iconClose the dialog box.
To store the adjustment data.
To clear the adjustment data.
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button.  Move
a red arrow pointer to the Mode that you want to clear and then
press SELECT button. 
						

							27
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and
less than 180 MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
MAC1280 x 96075.0075.08
MAC1280 x 102480.0075.08
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
XGA 101024 x 768
XGA 111024 x 768
XGA 121024 x 768
XGA 131024 x 768
62.0477.07
XGA 141024 x 768
61.0075.70
XGA151024 x 768
35.52286.96 
(Interlace)
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768
58.0372.0
SXGA 11152 x 864
SXGA 21280 x 1024
63.4879.35
SXGA 31280 x 1024
36.0087.17 
(Interlace)
SXGA 41280 x 1024
64.2070.40
SXGA 51280 x 1024
62.5058.60
SXGA 61280 x 1024
63.9060.00
SXGA 71280 x 1024
63.3459.98
SXGA 81280 x 1024
63.7460.01
SXGA 111152 x 900
71.6967.19
SXGA 121152 x 900
81.1376.107
SXGA 131280 x 1024
63.9860.02
SXGA 141280 x 1024
61.2065.20
71.4075.60
50.0086.00 
(Interlace)
HDTV720p––––––––
50.0094.00 
(Interlace)
45.0060.00
XGA 11024 x 768
XGA 21024 x 768
XGA 31024 x 768
XGA 41024 x 768
48.3660.00
68.67784.997
XGA 61024 x 768
60.02375.03
XGA 71024 x 768
56.4770.07
48.5060.02
44.0054.58
SXGA 91280 x 1024
SXGA 101280 x 960
79.97675.025
60.0060.00
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
SXGA 181280 x 1024
63.3760.01
76.9772.00
61.8566.00
46.4386.70 
(Interlace)
SXGA 191280 x 102463.7960.18
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
RGB––––––––15.73460 
(Interlace)RGB––––––––15.62550 
(Interlace)
HDTV1080i––––––––33.7560.00 
(Interlace)HDTV1035i––––––––33.7560.00 
(Interlace)
SVGA 10800 x 60032.7051.09
SXGA 201280 x 102491.14685.024 
						

							28
COMPUTER MODE
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
level that you want to set and then press SELECT button.
Move the red frame icon to the
level and press SELECT button.
The level being selected.
IMAGE SELECT MENU
Normal picture level preset on this projector.
Standard
Picture level adjusted for the picture with fine tone.
Real
User preset picture adjustment in IMAGE ADJUST Menu (P29).
IMAGE 1~4
IMAGE SELECT
Menu icon
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on the Remote Control Unit.IMAGE button
Standard
Real
Image 1
Image 2
Image 3
Image 4
Normal picture level preset on this projector.  This normal picture
level can also be selected by pressing NORMAL button.
Picture level adjusted for the picture with fine tone.
User preset picture adjustment in IMAGE ADJUST Menu (P29).
Standard
Real
IMAGE 1~4 
						

							29
COMPUTER MODE
Press POINT LEFT/RIGHT buttons
to adjust value.
Reset all adjustment to previous figure.
Reset
Stored
Closes IMAGE MENU.
Quit
Other icons operates as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust. and then press SELECT button.
The level of each item is displayed.  Adjust each level by
pressing POINT LEFT/RIGHT button(s).
Move a red frame pointer to
the item to be selected and
then press SELECT button.
IMAGE ADJUST MENU
IMAGE LEVEL ADJUSTMENT
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast.  (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter.  (From 0 to 63.)
Contrast
Brightness
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast.  (From 0 to 15.)
Gamma
3
To store manually preset image, move a red frame pointer to
STORE icon and press SELECT button.  Image Level Menu will
appear.  Move a red frame pointer to the Image 1 to 4 where you
want to set and then press SELECT button.
Image Level Menu
Move a red frame pointer to any of
Image 1 to 4 where you want to set
and then press SELECT button.
Stored icon
Press SELECT button at this icon to
store the adjustment.
IMAGE ADJUST
Menu icon
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Blue)
Selected Image level 
						

							30
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
Adjusts image size or pans image.  In “Digital Zoom” mode, the ON-
SCREEN MENU disappears and the magnifying glass icon and the
message “D. Zoom” is displayed.  
This projector also enters Digital Zoom mode by pressing the
D.ZOOM /button on Remote Control Unit.  
1
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM button or the
SELECT button.  The image is magnified by degrees. 
Compress function
To compress the image size, press the D.ZOOM button.  The
size of image is reduced by degrees.  
Panning function
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT
buttons.  Panning function can work only when the image is larger
than the screen size.
To return to screen size previously set, press NORMAL button.
To cancel Digital Zoom mode, press any button except D.ZOOM
/, SELECT, POINT, NORMAL or AUTO PC ADJ. button.
Provides image in its original size.  When the original image size is
larger than screen size (1366 x 768), this projector enters Digital
Zoom mode automatically.  Image size can be set to Normal by
pressing NORMAL button.
Move the red frame to the function and
press SELECT button.
Press POINT DOWN button and move a red frame pointer to the
function that you want to select and then press SELECT button.2
True
Digital Zoom
NOTE
This SCREEN Menu cannot be operated when
“HDTV720p,” “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu  (P23, 24).
True and Digital Zoom cannot be selected when
“RGB” is selected on SYSTEM Menu  (P23, 24).
This projector cannot display any resolution higher
than 1280 X 1024.  If your computer’s screen
resolution is higher than 1280 X 1024, reset the
resolution to the lower before connecting projector.
The image data in other than XGA (1024 x 768) is
modified to fit the screen size in the initial mode.
Panning function may not operate properly if the
computer system prepared on PC ADJUST Menu
is used.
Provides image to fit the vertical size of the screen.
Normal
Provides image to fit the horizontal size of the screen.
Full
SCREEN MENU
SCREEN Menu icon