Sanyo Projector Plc Xu115 User Manual

61

Maintenance and Cleaning
When	the	projection	 lamp	of	the	 projector	 reaches	its	end	 of	
life,	 the	Lamp	 replacement	 icon	appears	 on	the	 screen	 and	
LAMP 	REPLACE	 indicator	lights	yellow.	 Replace	 the	lamp	 with	
a	 new	 one	promptly.	 The	timing	 when	the	LAMP 	REPLACE	
indicator	should	light	is	depending	on	the	lamp	mode.
Follow	these	steps	to	replace	the	lamp.
Lamp
ORDER REPLACEMENT LAMP
Replacement	 lamp	can	be	ordered	 through	your	dealer.		 When	ordering	 a	projection	 lamp,	give	the...

6

Maintenance and Cleaning
This	projector	uses	a	high-pressure	lamp	which	must	be	handled	carefully	and	properly.		
Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
●	Lamp	 life	may	 differ	 from	lamp	 to	lamp	 and	according	 to	the	 environment	 of	use.	 There	 is	no	 guarantee	
of	 the	 same	 life	for	each	 lamp.	 Some	 lamps	 may	fail	or	terminate	 their	life	in	a	shorter	 period	of	time	
than	other	similar	lamps.
●	 If	 the	 projector	 indicates	 that	the	lamp...

6

 Problem:	 –	Solutions
  No power 	 –	Plug	the	power	cord	of	the	projector	into	the	AC	outlet.
	
	 	 –	See	if	the	POWER	indicator	lights	red.
	
	 	 –		
Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	
again.	 The	projector	can	be	turned	on	after	the	POWER	indicator	
turns	red.	See	page	22.
	 	 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights	red,		
	 	 	 projector	cannot	be	turned	on.	See	page	58.
	
	 	 –	Check	the	projection	lamp.	See	page	61.
	
	 	 –	Unlock...

6

Appendix
 No image	 –	Check	the	connection	between	your	computer	or	video	equipment		
	 	 	 and	the	projector.	See	pages	19-21.
	
	 	 –	See	if	the	input	signal	is	correctly	output	from	your	computer.	Some		
	 	 	 laptop	computers	may	need	to	change	the	setting	for	monitor	output		
	 	 			when	connecting	to	a	projector.	See	your	computer’s	instruction		
	 	 	 manual	for	the	setting.	
	
	 	 –	It	takes	about	30	seconds	to	display	an	image	after	turning	on	the		
	 	 	 projector.	See	page	22.
	 	 –...

65

Appendix
 The image is distorted or runs off .  –	Check	"PC	adjustment"	menu	or	"Screen"	menu	and	adjust	them.		
	 	 	 (page	33-34,	38-39)
  PIN code dialog box appears 	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“1234”	or	numbers	
	at start-up . 	 	 you	have	set).	See	pages	22,	54–55.
  Page Up/Down function does        –	Make	sure	your	computer	is	connected	to	the	projector	with	USB		
	not	work .      cable.(see	page	19)	 	 	 	 	 	 	
	 	 –	Check	cable	connection	between...

66

wARNING :
High voltages are used to operate this projector  . Do not attempt to open the cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	
projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	
how	to	obtain	service.
This	symbol	 on	the	 nameplate	
m e a n s 	t h e 	p r o d u c t 	i s 	L i s t e d	
by	 Underwriters	 Laboratories	
I n c . 	I t 	i s 	d e s i g n e d 	a n d	
m...

67

Appendix
Menu Tree
SVGA	1Mode	1Mode	2	-	-	-	-
Auto	PC	 Adj.
Total	dotsHorizontalVertical
Display	area	HDisplay	area	VReset
Dynamic
RealBlackboard	(Green)Image	1Image	2Image	3
Image AdjustContrastBrightnessColor	temp.
Red
Gamma
Store
Quit
NormalTrue
Digital	zoom	
–
Full	
0–630–63
Computer Input
PC Adjust
Mode	1Mode	2Mode	3Mode	4Mode	5
Image Select
High
0–63
0–15
Image	1Image	2Image	3Image	4
Screen
Quit
Yes/No
* 	 Systems	displayed	in	the	System	Menu	vary	
depending	on	an	input	signal.
ResetYes/No...

68

Appendix
AutoPALSECAMNTSCNTSC	4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard	(Green)
Image	1Image	2Image	3
Quit
Normal
0–630–63
Off
Setting
Image Select
System (2)
System (3)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15	0–15
Image	1
Screen
Yes/No
Quit
Image	4
LanguageSetting16	languages	provided.
On/OffOn/Countdown	off/Off	Logo	select
On/OffOn/Off
Off
On/OffAuto/High/Normal/Eco
Code	1–Code	8...

69

Check	the	indicators	for	projector	condition.																																				
•	•	•	green.•	•	•	red•	•	•	off
•	•	•	blinks	green.
When	the	projection	 lamp	reaches	 its	end	 of	life,	 the	LAMP 	REPLACE	 indicator	lights	yellow.	 When	this	indicator	
lights 	yellow, 	replace 	the 	projection 	lamp 	with 	a 	new 	one 	promptly. 	Reset 	the 	lamp 	replacement 	counter 	after	
replacing	the	lamp.	See	pages	61-62.
The	projector	is	off.	(The	 AC	power	cord	is	unplugged.)
The	projector	 is	in	 stand-by...

70

Appendix
Compatible Computer Specifications
Basically	this	projector	can	accept	the	signal	from	all	computers	with	the	V-,	H-Frequency	mentioned	below	
and	less	than	140	MHz	of	Dot	Clock	for	analog	signal	and	110	MHz	of	Dot	Clock	for	digital	signal.		When	selecting	these	modes,	PC	adjustment	can	be	limited.
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .(KHz)V-Freq .(Hz)
VGA	1640	x	48031.4759.88
VGA	2720	x	40031.4770.09
VGA	3640	x	40031.4770.09
VGA	4640	x	48037.8674.38
VGA	5640	x	48037.8672.81
VGA	6640	x...