Sanyo Projector Plc Xu115 User Manual

1

Installation
Connecting to Component Video Equipment
External	Audio	Equipment
COMPUTER/	COMPONENT
AUDIO	IN
Audio	cable	(stereo)
Audio	cable	
(stereo)
Audio	Input
Component	Video	Output
(Y,	Pb/Cb,	Pr/Cr)
RGB	Scart	21-
pin	Output Audio	Output
Component	
cable
COMPUTER	IN	2/COMPONENT 	IN	
Notes:
	 •	When 	the 	AUDIO 	OUT 	is 	plugged-in, 	the 	projector's	
built-in	speaker	is	not	available.
	 •	See	page	73	for	ordering	optional	cables.
			•	RGB	 Scart	signal	 cannot	 be	output	 from	the...



16
The	preparation	display	will	disappear	
after	30	seconds.
(See	page	53	for	Lamp	control	status.)
Lamp	control	status
Turning On the Projector
Connect 	the 	projector ’s 	AC 	power 	cord 	into 	an 	AC	
outlet.	 The	POWER	 indicator	 lights	red.
 Open	 the	lens	
cap	(see	pages	10,60).
Press 	the 	POWER 	ON/SYAND-BY 	button 	on 	the 	top	
control	 or		on	the	 remote	 control.	 The	POWER	 indicator	
lights	 green	 and	the	cooling	 fans	start	 to	operate.	 The	
preparation 	display 	appears...



TO	MAINTAIN 	THE 	LIFE 	OF 	THE 	LAMP, 	ONCE 	YOU	
TURN 	THE 	PROJECTOR 	ON, 	WAIT 	AT 	LEAST 	FIVE	
MINUTES	BEFORE	 TURNING	IT	OFF.
“Power	off?”	disappears	after	4	seconds.
Turning Off the Projector
Press	the 	POWER 	ON/STAND-BY 	button 	on 	the 	top	
control 	or 	on 	the 	remote 	control, 	and 	“Power 	off?”	
appears	on	the	screen.
Press	 the	POWER	 ON/STAND-BY 	button	 again	to	turn	
off	 the	 projector.	 The	POWER	 indicator	 starts	to	blink	
red,	 and	the	cooling	 fans	keep	 running....



Basic Operation
How to Operate the On-Screen Menu
The	projector 	can 	be 	adjusted 	or 	set 	via 	the 	On-Screen	
Menu.	 For	each	 adjustment	 and	setting	 procedure,	 refer	to	
the	respective	sections	in	this	manual.
Use	the	Point	
◄►	buttons	 to	select	 a	Menu	 icon.	Use	
the	 Point	
▲▼	buttons	 to	select	 an	item	 in	the	 selected	
menu.
Press	 the	SELECT 	button	 to	show	 the	item	 data.	 Use	
the	Point	
◄►	buttons	to	adjust	the	values.
To	 close	 the	On-Screen	 Menu,	press	the	MENU...

5

Menu Bar
PC System Menu
Image Adjust Menu
U s e d	t o 	a d j u s t 	c o m p u t e r	
image 	[Contrast/Brightness/	
Color 	temp./White 	balance	
(R/G/B)/Sharpness/Gamma]	
(pp.37–38).
Setting Menu
Used 	to 	adjust	
t h e 	v o l u m e 	o r	
mute 	the 	sound	
(p.27).
Image Select Menu
Used	to	select	an	
image	mode	among	
Dynamic,	Standard,	Real,	
Blackboard(Green),	and	
Image	1–4	(p.36).
For computer source
AV System Menu
Used	to	select	
system	of	selected	
video	source	(p.42).
Image Adjust Menu
U s...

6

Basic Operation
Rotate	the	Zoom	Lever	to	zoom	in	and	out.		
Rotate	the	Focus	Ring	to	adjust	the	focus	of	the	image.		
Zoom and Focus Adjustment
Zoom	Lever
Focus	Ring
If	a 	projected 	picture 	still 	has 	keystone 	distortion 	after	
pressing	 the	AUTO	 SETUP/CANCEL 	button	 on	the	 top	control	
or 	the 	AUTO 	SET/CANCEL 	button 	on 	the 	remote 	control,	
correct	the	image	manually	as	follows:
Press 	the 	KEYSTONE 	button 	on 	the 	remote 	control. 	The	
Keystone	 dialog	box	appears.	 Use	the...

7

Sound Adjustment
1

Press	the	MENU	button	to	display	the	On-Screen	Menu.	
Use	the	Point	
◄►	buttons	to	move	the	red	frame	pointer	
to	the	Sound	Menu	icon.
Press	 the	VOLUME+/–	 buttons	on	the	 top	control	 or	on	 the	
remote	 control	to	adjust	 the	volume.	 The	volume	 dialog	box	
appears	on	the	screen	for	a	few	seconds.
Press	 the	MUTE	 button	on	the	 remote	 control	to	temporarily	
turn 	off 	the 	sound. 	To 	turn 	the 	sound 	back 	on, 	press 	the	
MUTE	button	 again	or	press	 the	VOLUME...

8

Basic Operation
Remote Control Operation
Using	the 	remote 	control 	for 	some 	frequently 	used 	operations 	is 	advisable. 	Just 	pressing 	one 	of 	the 	buttons	
enables	you	to	make	the	desired	operation	quickly	without	calling	up	the	On-Screen	Menu.
Press 	the 	COMPUTER, 	VIDEO, 	or 	NETWORK 	button 	on	
the	 remote	 control	to	select	 the	input	 source.	 See	pages	 30-
31,	40-41	for	details.
Refer	 to	the	 owner's	 manual	"Network	 Set-up	and	Operation"	
for	details	about	the...

9

Basic Operation
black	out		the	captured	image		normal		•	•	•	•	•
Press	 the	NO	 SHOW	 button	on	the	 remote	 control	to	black	 out	
the 	image. 	To 	restore 	to 	normal, 	press 	the 	NO 	SHOW 	button	
again 	or 	press 	any 	other 	button. 	When 	a 	projected 	image 	is	
captured 	and 	set 	as 	“User” 	in 	the 	Logo 	selection 	(p.49), 	the	
screen	 changes	 each	time	you	press	 the	NO	 SHOW	 button	as	
follows.
NO SHOw button
Press	the	P-TIMER	 button	on	the	 remote	 control.	 The	P-Timer...

0

Choose	either 	Computer 	1 	(Analog) 	or 	Computer 	2 	by	
pressing	 the	INPUT 	button	 on	the	 top	control	 or	press	 the	
COMPUTER	button	on	the	remote	control.
Before	 using	these	 buttons,	 correct	input	source	 should	be	
selected	through	Menu	operation	as	described	below.
Press 	the 	MENU 	button 	to 	display 	the 	On-Screen	
Menu. 	Use 	the 	Point 	
◄►	buttons 	to 	move 	the 	red	
frame	pointer	to	the	Input	Menu	icon.1Input Menu
Use 	the 	Point 	▲▼	buttons 	to 	move 	the 	red 	arrow...