Sanyo Projector Plc Xd2200 User Manual

61

Maintenance and Cleaning
Cleaning the Projector Cabinet
Cleaning the Projection Lens
Unplug	the	AC	power	cord	before	cleaning.
Gently	wipe	the	projection	 lens	with	a	cleaning	 cloth	that	
c o n t a i n s 	a 	s m a l l 	a m o u n t 	o f 	n o n - a b r a s i v e 	c a m e r a 	l e n s	
c l e a n e r, 	o r 	u s e 	a 	l e n s 	c l e a n i n g 	p a p e r 	o r 	c o m m e r c i a l l y	
available	air	blower	to	clean	the	lens.	
Avoid 	using 	an 	excessive 	amount 	of 	cleaner. 	Abrasive	
cleaners,...

62

Maintenance and Cleaning
When	the	projection	lamp	of	the	projector	reaches	its	end	
of	life,	the	Lamp	replacement	icon	appears	on	the	screen	
and	LAMP	REPLACE	indicator	lights	yellow.	Replace	the	
lamp	with	a	new	one	promptly.	 The	timing	when	the	LAMP	
REPLACE	indicator	should	light	is	depending	on	the	lamp	
mode.
Follow	these	steps	to	replace	the	lamp.
For	continued	safety,	replace	with	a	lamp	of	the	
same	type.	Do	not	drop	a	lamp	or	touch	a	glass	
bulb!	The	glass	can	shatter	and	may	cause...

6

Maintenance and Cleaning
This	projector	uses	a	high-pressure	lamp	which	must	be	handled	carefully	and	properly.		
Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
● Lamp li�e ma��di��er�rom lamp to lamp and according to the en�ironment o� use. There is no guarantee	Lamp	 life	may	 differ	 from	lamp	 to	lamp	 and	according	 to	the	 environment	 of	use.	 There	 is	no	 guarantee	
of	the	 same	 life	for	each	 lamp.	 Some	 lamps	 may	fail	or	terminate	 their	life	in	a...

64

 Problem:	 –	Solutions
 No power	 –	Plug	the	power	cord	of	the	projector	into	the	AC	outlet.	
	 	 –	See	if	the	POWER	indicator	lights	red.	
	 	–		
Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	
again.	 The	projector	can	be	turned	on	after	the	POWER	indicator	
turns	red.	See	page	18.
	 	 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights	red,																	
	 		 projector	cannot	be	turned	on.	See	page	59.	
	 	–	Check	the	projection	lamp.	See	page	62.	
	 	–...

65

Appendix
 No image	–	Check	the	connection	between	your	computer	or	video	equipment		
	 	 	 and	the	projector.	See	pages	14-16.	
	 	–	See	if	the	input	signal	is	correctly	output	from	your	computer.	Some		
	 		 laptop	computers	may	need	to	change	the	setting	for	monitor	output		
	 				when	connecting	to	a	projector.	See	your	computer’s	instruction		
	 		 manual	for	the	setting.		
	 	–	It	takes	about	30	seconds	to	display	an	image	after	turning	on	the		
	 		 projector.	See	page	18.
	 	–		
Check	the...

66

Appendix
 The image is distorted or runs off . –	Check	PC adjust	menu	or	Screen	menu	and	adjust	them.		 	
	 	 			See	pages	30-31,	34-35.
 PIN code dialog box appears	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“1234”	or	numbers	
	at start-up .	 	 you	have	set).	See	pages	19,	54-55.
 The Remote Control does	 –	Check	the	batteries.	
	not work .	 –	Make	sure	no	obstruction	is	between	the	projector	and	remote	 	
	 	 			control.	
	 	–	Make	sure	you	are	not	too	far	from	the	projector	when	using...

67

wARNING :
High voltages are used to operate this projector  . Do not attempt to open the cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	
projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	
how	to	obtain	service.
This	symbol	on	the	nameplate	
means	the	product	is	Listed	
by	Underwriters	Laboratories	
Inc.		It	is	designed	and	
manufactured	to	meet	rigid	
U.L.	safety...

68

Appendix
Menu Tree
SVGA	1Mode	1Mode	2	-	-	-	-
Total	dotsHorizontalVertical
Display	area	HDisplay	area	VReset
Dynamic
RealBlackboard	(Green)
Image	1Image	2Image	3
Image AdjustContrastBrightnessColor	temp.
Red
Gamma
Store
NormalTrue
Digital	zoom	–
Custom
0–630–63
Computer Input
PC adjust
Mode	1Mode	2Mode	3Mode	4Mode	5
Image select
0–63
0–15
Image	1Image	2Image	3Image	4Screen
Yes/No
	*	Systems	displayed	in	the	System	Menu	vary	depending	on	an	input	signal.
ResetYes/No
Sharpness0–15
Computer Input/Video...

69

Appendix
AutoPALSECAMNTSCNTSC	4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard	(Green)
Image	1Image	2Image	3
Normal
0–630–63
Off
Image select
System (2)
System (3)
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0–630–630–630–15	0–15
Image	1
Screen
Yes/No
Image	4
Standard
OffNoise	reductionL1L2
0–630–63
Image	2Image	3Image	4
L2L1
Film
Color	temp.
Wide
Scale
PositionCommonReset
H/V
H/VYes/NoYes/No
Custom	adj.
On/OffH&V...

70

Check	the	indicators	for	projector	condition.																																			
•	•	•	green.•	•	•	red•	•	•	off
•	•	•	blinks	green.
When	the	projection	lamp	reaches	its	end	of	life,	the	LAMP	REPLACE	indicator	lights	yellow.	When	this						
indicator	lights	yellow,	replace	the	projection	lamp	with	a	new	one	promptly.	(pp.	56,	62)
The	projector	is	off.	(The	AC	power	cord	is	unplugged.)
The	projector	is	in	stand-by	mode.	Press	the	ON/STAND-BY 	button	
to	turn	on	the	projector.
Projector...