Sanyo Projector Plc Xd2200 User Manual

11

Part Names and Functions
✔Note:
To	ensure	safe	operation,	please	observe	the	following	precautions:
–	 Do	not	bend,	drop	or	expose	the	remote	control	to	moisture	or	heat.
–	 For	cleaning,	 use	a	soft	 dry	cloth.	 Do	not	 apply	 benzene,	 thinner,	spray,	
or	any	chemical	material.
Remote Control
⑦
⑭⑩
⑳④
⑱
②
⑧
⑨
⑬
⑯
⑤
⑥
⑪
⑫
⑲
⑮
③
②	AUTO SET buttonExecute	the	setting	of	 Auto	setup	(includes	Input	search,	 Auto	PC	adj.	and	Auto	Keystone	functions)	in	the	setting	menu.(pp.23,	44)
⑤ S-VIDEO button...

12

Part Names and Functions
To	ensure	safe	operation,	please	observe	the	following	precautions	:
	●	 Use	two	(2)	AAA	or	LR03	type	alkaline	batteries.
	●	 Always	replace	batteries	in	sets.
	●	 Do	not	use	a	new	battery	with	a	used	battery.
	●	 Avoid	contact	with	water	or	liquid.
	●	 Do	not	expose	the	remote	control	to	moisture	or	heat.
	●	 Do	not	drop	the	remote	control.
	●	 If	the	battery	has	leaked	on	the	remote	control,	carefully	wipe	the	case	clean	and	install	new	batteries.
	●	 Risk	of	an	explosion...

1

Positioning the Projector
For	projector	 positioning,	 see	the	figures	 below.	The	projector	 should	be	set	 perpendicularly	 to	the	 plane	 of	the	
screen.
Installation
✔Note:
	 •	The 	brightness 	in 	the 	room 	has 	a 	great 	influence 	on 	picture 	quality. 	It 	is 	recommended 	to 	limit 	ambient	
lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
Adjustable Foot
Adjustable	Foot
Foot	Lock	Latch
Projection	angle	can	be	adjusted...

14

Installation
Connecting to a Computer
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	
cables.
Cables used for connection 
•	VGA	Cables	(Mini	D-sub	15	pin)	*(Only	one	cable	is	supplied.)
•	Audio	Cables
(*One	cable	is	supplied;	other	cables	are	not	supplied	with	the	projector.)
✔Note:
	 •	Input	sound	to	the	 AUDIO	IN	terminal	when	using	the	COMPUTER	IN	1/	S-VIDEO	IN	/	COMPONENT 	IN
				and	the	COMPUTER	IN	2/MONITOR	OUT	terminals	as	input.
	 •...

15

Installation
Connecting to Video Equipment
Cables used for connection  
•	Video	Cable	
•	S-Video	Cable	
•	S-Video-VGA	Cable	
•	Audio	Cables
(Cables	are	not	supplied	with	the	projector.	)
✔Note:
	 •	When	the	 AUDIO	OUT	is	plugged-in,	the	projector's	built-in	speaker	is	not	available.
	 •	See	page	73	for	ordering	optional	cables.
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	 AC	outlet	before	connecting	
cables.
External	Audio	Equipment
Audio	cable			(stereo)
S-Video...

16

Installation
Connecting to Component Video and RGB (Scart) Equipment
✔Note:
	 •	When	the	AUDIO	OUT	is	plugged-in,	the	projector's	built-in	speaker	is	not	available.
	 •	See	page	73	for	ordering	optional	cables.
Cables used for connection	
•	Audio	Cables	
•	Scart-VGA 	Cable	
•	Component	Cable	
•	Component-VGA 	Cable	
(Cables	are	not	supplied	with	this	projector.)		
External	Audio	Equipment
AUDIO	IN
Audio	cable	(stereo)
Audio	cable	(stereo)
Audio	Input
Component	Video	Output(Y,	Pb/Cb,	Pr/Cr)Audio...

17

Installation
Connecting the AC Power Cord
This	projector	 uses	nominal	 input	voltages	 of	100-240	 V	AC	
and 	it 	automatically 	selects 	the 	correct 	input 	voltage. 	It 	is	
designed	 to	work	 with	single-phase	 power	systems	 having	a	
grounded	 neutral	conductor.	 To	reduce	 the	risk	 of	electrical	
shock,	do	not	plug	into	any	other	type	of	power	system.
If	you 	are 	not 	sure 	of 	the 	type 	of 	power 	being 	supplied,	
consult	your	authorized	dealer	or	service	center.
Connect 	the 	projector...

18

The	preparation	display	will	disappear	
after	30	seconds.
(See	page	53	for	Lamp	control	status.)
Turning On the Projector
Connect	the	projector’s	AC	power	cord	into	an	AC	
outlet.	The	POWER	indicator	lights	red.	Open	the	lens	
cap	(see	pages	8,	61).
Press	the	ON/STAND-BY 	button	on	the	top	control	or	
on	the	remote	control.	The	POWER	indicator	lights	
green	and	the	cooling	fans	start	to	operate.	 The	
preparation	display	appears	on	the	screen	and	the	
countdown	starts.	
2

1Complete	peripheral...

19

what is PIN code?
PIN	(Personal	Identification	Number)	code	is	a	security	
code	that	allows	the	person	who	knows	it	to	operate	the	
projector.	Setting	a	PIN	code	prevents	unauthorized	use	of	
the	projector.
A	PIN	code	consists	of	a	four-digit	number.	Refer	to	the	PIN	
code	lock	function	in	the	Setting	Menu	on	pages	54-55	for	
locking	operation	of	the	projector	with	your	PIN	code.
Enter a PIN code
Use	the	Point	▲▼	buttons	to	enter	a	number.	Press	the	
Point	◄	►	buttons	to	fix	the	number	and	move	the...

20

TO	MAINTAIN	THE	LIFE	OF	THE	LAMP,	ONCE	
YOU	TURN	 THE	PROJECTOR	ON,	WAIT 	AT 	
LEAST 	FIVE	MINUTES	BEFORE	 TURNING	IT	
OFF.
Power off?	disappears	after	4	seconds.
Turning Off the Projector
Press	the	ON/STAND-BY 	button	 on	the	 top	control	 or	
on	the	 remote	 control,	 and	Power off? appears	 on	the	
screen.
Press 	the 	ON/STAND-BY 	button 	again 	to 	turn 	off 	the	
projector.	 The	POWER	 indicator	 starts	to	blink	 red,	and	
the	cooling	 fans	keep	 running.	 (You	can	select	 the	level	
of	fans’...