Sanyo Projector Plc Wxu700a User Manual

51

Off

Capture
Capture
This function enables you to capture an image being 
projected to use it for a starting-up display or interval of 
presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select yes to capture the 
projected image.
After capturing the projected image, go to the Logo select 
function and set it to User. Then the captured image will be 
displayed the next time you turn on the projector or when 
you press the NO SHOW button (see page 29).
To...

5

Setting
Enter a Logo PIN code
Use  the  Point ▲▼  buttons  to  enter  a  number.  Press  the 
Point ► button to fix the number and move the red frame 
pointer  to  the  next  box.  The  number  changes  to .  If 
you fixed an incorrect number, use the Point ◄ button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
Repeat this step to complete entering a four-digit 
number.
After entering the four-digit number, move the pointer to 
Set. Press the SELECT...

53

Setting
Ceiling 
Rear 
Ceiling
When  this  function  is  set  to On,  the  picture  will  be  top/
bottom  and  left/right  reversed.  This  function  is  used  to 
project the image from a ceiling-mounted projector.
Rear
When  this  function  is  set  to On,  the  picture  will  be  left/right 
reversed.  This  function  is  used  to  project  the  image  from 
rear of the screen.
HDMI setupHDMI setup
This function is only used for HDMI input source.
  Image
              Normal:         When the...

54

Setting
Arrow
PointerPointer
You can emphasize a part of the projected image with this 
function. Use the Point ▲▼ buttons to choose Spotlight 
(Large, Middle or Small) , Arrow, Finger or Dot and press 
the SELECT button. See "Pointer Function" on page 14.
Standby mode
This function is available when operating the projector via 
network.
 Network ....  Supply the power to the network function even 
after turning off the projector. You can turn on/
off the projector via network, modify...

55

Setting
Picture in PictureThis function is used to project two videos simultaneously
by placing a separate small sub screen within the main
screen. (Picture in Picture combinations provided in this 
projector are shown on pages 78.)
Only the sound on the main picture is heard, the sound
on the sub picture cannot be heard.( In P in P, the big 
picture is main picture, and the small one is sub picture; in P 
by P, the left picture is main picture, and the right one is sub 
picture.)
  Mode .
 . . . ....

56

Power management
Timer left before Lamp is off.
Power managementFor reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not operated for a 
certain period.
Select one of the following options:
Ready ..................  When the lamp has been fully cooled 
down, the POWER indicator changes 
to green blinking. In this condition, the 
projection lamp will be turned on if the 
input signal is reconnected or...

57

Setting
On start
When this function is set to On, the projector will be 
automatically turned on just by connecting the AC power 
cord to a wall outlet. 
Note:
  Be sure to turn off the projector properly (see "Turning Off 
the Projector" on page 23). If the projector is turned off 
in the incorrect sequence, the On start function does not 
work properly.
Closed caption
Closed caption is a printed version of the program sound or 
other information displayed on the screen. If the input...

58

Remote control
Lamp control 
Remote control
The eight different remote control codes (Code 1-Code 8) 
are assigned to the projector; the factory-set, initial code 
(Code 1) and the other seven codes (Code  to Code 8). 
The same code should set on both the projector and the 
remote control. For example, operating the projector in 
Code 7, the remote control code also must be switched to 
Code 7.
 To change the code for the projector
  Select a remote control code in this Setting Menu.
 To change...

59

Setting
Key lock
Key lockSecurity (Key lock and PIN code lock)
PIN code lock
This function locks the top control and remote control 
buttons to prevent operation by unauthorized persons. .....  Unlocked.
  .....  Lock the operation of the top control. To 
unlock, use the remote control.
  .....  Lock the operation of the remote control.    
To unlock, use the top control.
If the top control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with...

60

Setting
Use the Point ▲▼ buttons to select Off, On1 or On. 
Press the SELECT button to close the dialog box. Change the PIN code lock setting
Enter a PIN code
Use the Point ▲▼  buttons to enter a number. Press the 
Point ► button to fix the number and move the red frame 
pointer to the next box. The number changes to . If 
you fixed an incorrect number, use the Point ◄ button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
Repeat this step to...