Sanyo Projector Plc Wxu700a User Manual

41

Video Input
Choose Computer  1 by  pressing  the  INPUT  button  on  the  top  control  or  press  the  COMPUTER  button  on  the 
remote control; choose HDMI by pressing the INPUT button on the top control or press the HDMI button on the 
remote control. 
Before  using  these  buttons,  correct  input  source  should  be  selected  through  Menu  operation  as  described 
below.
1
Input Menu
Use the Point ▲▼ buttons to select Computer 1 and 
then press the Point ► button; use the Point ▲▼...

4

Video Input
Video System Selection
1AV System Menu (Video or S-video)
AV System Menu (Component)

If the projector cannot reproduce proper video image, 
select a specific broadcast signal format from among PAL, 
SECAM, NTSC, NTSC 4 .43, PAL-M and PAL-N.
PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
The projector automatically detects an incoming video 
signal, and adjusts itself to optimize its performance.
If the projector cannot reproduce proper video image, select 
a specific component video...

43

Image Select Menu
Select the desired image mode among Dynamic, Standard, 
Cinema, Blackboard (Green), Colorboard, Image 1, 
Image 
, Image 3 and Image 4 by pressing the IMAGE 
button on the remote control.
Standard
Picture mode adjusted with fine tone.
Cinema
Blackboard (Green)
Image 1–4
IMAGE button
Dynamic
Cinema
Image Mode Selection 
Blackboard (Green)
Dynamic
Standard
Remote Control
IMAGE button
Direct Operation
For viewing pictures in a bright room.
Normal picture mode preset on the...

44

Video Input
Image Adjustment
1

Press the Point ◄ button to decrease the contrast; press the 
Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press  
the Point ► button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point ◄ button to lighten red tone; press the Point 
► button to deepen red tone (from 0 to 63).
White balance (Red)
Press the Point ◄ button to lighten green tone; press the 
Point ► button to...

45

Video Input
Use  the  Point ◄►  buttons  to  adjust  the  gamma  value  to 
obtain a better balance of contrast (from 0 to 15).
Gamma
Press the Point ◄ button to decrease the sharpness of the 
image; press the Point ► button to increase the sharpness 
of the image (from 0 to 15).
Sharpness
An interlaced video signal can be displayed in progressive 
mode. Select one of the following options.
 Off .........  Disabled.
 L1  ..........  For an active picture.
  L  ..........  For a still picture....

46

Video Input
This projector has the picture screen resize function, which enables you to customize the image size.
Normal
Screen Size Adjustment
Screen Menu1

Provide the image to fit the screen size while maintaining
the aspect ratio of input signal.
Custom
Adjust the screen scale and position manually with this 
function.
Press the Point ► button at Custom and the Custom is
displayed on the screen, you can use the Point ▲▼ buttons
to choose the item you want to adjust.
 Scale H/V .............

47

HDMI setupTerminal                                                        Computer 2Pointer                                                          DotStandby mode                                               Eco

Language
The language used in the On-Screen Menu is available in 
English, German, French, Italian, Spanish, Portuguese, 
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian, 
Russian, Chinese, Korean, japanese and Thai.
Setting Menu
Setting
Setting
HDMI setupTerminal...

48

Setting
Note:
 • Auto Keystone corrects vertical distortion only, not 
correct horizontal distortion.
  • The 
Auto Keystone function cannot work when the 
Ceiling feature is set On in the Setting menu (p.53).
  • Perfect correction of the image distortion cannot 
be ensured with the Auto setup function. If the 
distortion is not corrected properly by pressing the 
AUTO SETUP/CANCEL button, adjust manually 
by pressing the KEYSTONE button on the remote 
control or selecting Keystone in the Setting...

49

Keystone
This function is used to store or reset the keystone 
correction when the AC power cord is unplugged.
 Store .......  Keep the keystone correction even when the 
AC power cord is unplugged.
 Reset  .......  Release the keystone correction when the AC 
power cord is unplugged.
To correct keystone distortion, press the SELECT button. 
Keystone appears on the screen. Use the Point ▲▼ 
buttons to correct keystone distortion (p.26).
Background
Select the background screen for when no input...

50

Setting
Logo (Logo and Logo PIN code lock settings)
HDMI setupTerminal                                                        Computer 2Pointer                                                          DotStandby mode                                               Eco
Logo select
This function allows you to customize the screen logo with 
Logo select, capture, Logo PIN code lock and Logo PIN 
code change functions.
Note:
    When 
On is selected in the Logo PIN code lock function, 
Logo select,...