Sanyo Projector Plc Wxu700a User Manual

							
51

Off

Capture
Capture
This function enables you to capture an image being 
projected to use it for a starting-up display or interval of 
presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select yes to capture the 
projected image.
After capturing the projected image, go to the Logo select 
function and set it to User. Then the captured image will be 
displayed the next time you turn on the projector or when 
you press the NO SHOW button (see page 29).
To cancel the capture function, select  yes in the "Quit?" 
confirmation box.
Note:
  • Before capturing an image, select 
Standard in the 
Image Select Menu to capture a proper image (pp.36, 
43).
  • A signal from a computer can be captured up to WXGA 
(1280 x800). A signal from video equipment can be 
captured except for 720p, 1035i and 1080i.
  • When capturing the image that has been adjusted by 
the Keystone function, the adjusted data is automatically 
reset and the projector captures an image without 
keystone correction. 
  • When 
Logo PIN code lock is set to On, capture cannot 
be selected.   
  • When starting to capture a new image, the previously 
stored image is cleared even if you cancel the capturing.
  •  When there is no captured image or it is interrupted 
while capturing an image, User cannot be selected, you 
can only switch between Default and Off.
Off
Logo PIN code lockThis function prevents an unauthorized person from 
changing the screen logo.
 Off  ...........  The screen logo can be changed freely from 
the Logo Menu (p.50).
 On  ...........  The screen logo cannot be changed without a 
Logo PIN code.
If you want to change the Logo PIN code lock setting, 
press the SELECT button and the Logo PIN code dialog 
box appears. Enter a Logo PIN code by following the steps 
below. The initial Logo PIN code is set to "4321" at the 
factory.
Logo PIN code lock
Setting 
						

							
5

Setting
Enter a Logo PIN code
Use  the  Point ▲▼  buttons  to  enter  a  number.  Press  the 
Point ► button to fix the number and move the red frame 
pointer  to  the  next  box.  The  number  changes  to .  If 
you fixed an incorrect number, use the Point ◄ button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
Repeat this step to complete entering a four-digit 
number.
After entering the four-digit number, move the pointer to 
Set. Press the SELECT button so that you can start to 
operate the projector.
If  you  entered  an  incorrect  Logo  PIN  code, Logo  PIN 
code  and  the  number  (   )  will  turn  red  for  a 
moment. Enter the correct Logo PIN code all over again.
Logo PIN code can be changed to your desired four-digit 
number. Press the Point ▼ button to select Logo PIN 
code change and then press the SELECT button. The 
New Logo PIN code input dialog box appears. Set a new 
Logo PIN code.  
Be sure to note the new Logo PIN code and keep it on 
hand. If you lost the number, you could no longer change 
the Logo PIN code setting. For details on PIN code 
setting, refer to "PIN code lock" on pages 59-60.
Use the Point ▲▼ buttons to switch On or Off, and then 
press the SELECT button to close the dialog box.
Change the Logo PIN code lock setting
Enter a Logo PIN code
After a correct Logo PIN code 
is entered, the following dialog 
box appears.
CAUTION:
WHEN yOU HAVE CHANGED THE LOGO PIN 
CODE, WRITE DOWN THE NEW PIN CODE 
IN COLUMN OF THE LOGO PIN CODE NO . 
MEMO ON PAGE 83, AND KEEP IT SECUREL y . 
SHOULD THE LOGO PIN CODE BE LOST OR 
FORGOTTEN, THE LOGO PIN CODE SETTING 
CAN NO LONGER BE CHANGED .
Change the Logo PIN code lock setting
Off
Logo PIN code change
Change the Logo PIN code
Next 
						

							
53

Setting
Ceiling 
Rear 
Ceiling
When  this  function  is  set  to On,  the  picture  will  be  top/
bottom  and  left/right  reversed.  This  function  is  used  to 
project the image from a ceiling-mounted projector.
Rear
When  this  function  is  set  to On,  the  picture  will  be  left/right 
reversed.  This  function  is  used  to  project  the  image  from 
rear of the screen.
HDMI setupHDMI setup
This function is only used for HDMI input source.
  Image
              Normal:         When the output of Digital R/G/B   
                                    equipment is set to Standard.  
              
Enhanced:    When the output of Digital R/G/B 
                                    equipment is set to Enhanced.
 
  Sound
              HDMI:            When Digital input source is input,   
                                    Sound is set to HDMI.
               Computer 
: When DVI input source is changed to 
                                    HDMI input source, Sound is set to 
                                     Computer .
The names for the output setting of Digital R/G/B vary
from equipment to equipment. For details, refer to the
owner’s manual of your Digital R/G/B equipment.
When the black parts of the image are destroyed or stand 
out, please switch to Normal or Enhanced, and then switch
the output type of the HDMI Digital R/G/B output equipment.
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back
of the projector is switchable for computer 2 input or monitor
output. (See page 10) 
  Computer 
 . . .  Computer input
  Monitor out . . .  Monitor out
Terminal function is not available when selecting Computer
 to the input source. Change the input source to the others
(HDMI or Computer 1 or Video) so that the Terminal 
function will be available. (pp.30-31, 40-41) 
						

							
54

Setting
Arrow
PointerPointer
You can emphasize a part of the projected image with this 
function. Use the Point ▲▼ buttons to choose Spotlight 
(Large, Middle or Small) , Arrow, Finger or Dot and press 
the SELECT button. See "Pointer Function" on page 14.
Standby mode
This function is available when operating the projector via 
network.
 Network ....  Supply the power to the network function even 
after turning off the projector. You can turn on/
off the projector via network, modify network 
environment, and receive an e-mail about 
projector status while the projector is powered 
off.
 Eco  ............  Select Eco when you do not use the projector 
via network. The projector’s network function 
will stop when turning off the projector.
Refer to the owner’s manual of “Network Set-up and 
Operation”.
Note:
•  Factory default is 
Network.
•  When selecting 
Network, the cooling fans may be running 
  depending on the temperature inside the projector even if 
  the projector is turned off. 
						

							
55

Setting
Picture in PictureThis function is used to project two videos simultaneously
by placing a separate small sub screen within the main
screen. (Picture in Picture combinations provided in this 
projector are shown on pages 78.)
Only the sound on the main picture is heard, the sound
on the sub picture cannot be heard.( In P in P, the big 
picture is main picture, and the small one is sub picture; in P 
by P, the left picture is main picture, and the right one is sub 
picture.)
  Mode .
 . . . . P in P :  The sub picture in the main picture.
                     P by P:  The sub picture by the main picture.
                     Off     :   Exit the Picture in Picture menu.
  Subpicture size .
 . .  Select the subpicture display size. 
                                    Subpicture can be changed  
                                    between Large, Small and Middle. 
  Subpicture position. .  Set a position for subpicture.This 
                                         function is used to set Subpicture 
                                         position as follows:
                                         the top left→ the bottom left →
                                         the bottom right→ the top right→ • • •
Selecting the Main picture or Sub picture
During Picture in Picture mode, and no operation on the On 
Screen Menu, press the SELECT button to select main or 
sub picture. (When the sub picture is selected,  a red frame 
will be displayed.)
Switching of the Input Source
In the main picture or the sub picture mode, choose input 
source by pressing the INPUT button on the top control or 
pressing the COMPUTER、VIDEO、HDMI or NETWORK 
button on the remote control or through Input Menu 
operation.
Operation of the Sub picture
In Picture in Picture mode, press the SELECT button to 
select the sub picture (the frame becomes to  red), and 
then use the Point ▲▼◄► buttons to change Subpicture 
size, switch the Main picture and the Sub picture, and move 
Subpicture position.
   • In Picture in Picture mode, press the Point ▲ button to   
     switch the Main picture and the Sub picture. 
   • In P in P,  press the Point ▼ button to change Subpicture   
     size.
   • In P in P,  press the Point ◄► buttons to move 
     Subpicture position.
Picture in Picture
Note:
• When the input signal(s) is/are incompatible, X mark will
  be displayed on the Main/Sub picture.
• When the sub picture is set to the same signal as the main
  picture, X mark will be displayed.
  • Subpicture position and Subpicture size are only used  
    for P in P.
Subpicture size
Note:
• When P in P or P by P is set, Total dots is 
  disabled in the PC adjust menu. 
• In Picture in Picture mode, the Freeze function 
  is disabled.
• During Picture in Picture mode and the Menu 
  screen is displayed, via the remote control 
  operation, these functions are disabled as 
  below:
   • Change Subpicture size.
   • Move Subpicture position.
   • Switching of the Main picture and Sub picture.
   • Select the Sub picture mode by the SELECT   
     button. 
						

							
56

Power management
Timer left before Lamp is off.
Power managementFor reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not operated for a 
certain period.
Select one of the following options:
Ready ..................  When the lamp has been fully cooled 
down, the POWER indicator changes 
to green blinking. In this condition, the 
projection lamp will be turned on if the 
input signal is reconnected or any button 
on the top control or remote control is 
pressed. 
Shut down  ..........  When the lamp has been fully cooled 
down, the power will be turned off. 
Off  .......................  Power management function is off. 
Timer  ...................  If the input signal is interrupted and 
no button is pressed for more than 
30 seconds, the timer display with No 
signal appears. It starts the countdown 
until the lamp is turned off. Use the Point 
▲▼ buttons to set the Timer(1~30min).
Note:
  Factory default is Ready: 5 min.min
min
Setting 
						

							
57

Setting
On start
When this function is set to On, the projector will be 
automatically turned on just by connecting the AC power 
cord to a wall outlet. 
Note:
  Be sure to turn off the projector properly (see "Turning Off 
the Projector" on page 23). If the projector is turned off 
in the incorrect sequence, the On start function does not 
work properly.
Closed caption
Closed caption is a printed version of the program sound or 
other information displayed on the screen. If the input signal 
contains closed captions, you can turn on the feature and 
switch the channels. Press the Point ▲▼ buttons to select 
Off, CC1, CC, CC3 or CC4.  
If the closed caption is not clear, you can change the text 
from Color to White.
Closed Caption
Note:
The Closed Caption is available only under the situation 
below.
   • When the input signal is NTSC of composite and         
      S-video, and the system is set according to the signal  
      or set on Auto.  
    • The system must be set on 
NTSC or Auto  in Video    
  System Selection. (p.42) 
    • The icon of Closed caption is displayed in gray while it 
       is not available. 
    • 
The Closed caption is unavailable when On-Screen
      menu and P-Timer are displayed, and Picture in 
       Picture is active.Press the Point ▲▼ buttons to select 
Off, CC1, CC, CC3 or CC4, and then 
Press the SELECT button. 
						

							
58

Remote control
Lamp control 
Remote control
The eight different remote control codes (Code 1-Code 8) 
are assigned to the projector; the factory-set, initial code 
(Code 1) and the other seven codes (Code  to Code 8). 
The same code should set on both the projector and the 
remote control. For example, operating the projector in 
Code 7, the remote control code also must be switched to 
Code 7.
 To change the code for the projector
  Select a remote control code in this Setting Menu.
 To change the code for the remote control:
  While holding down the MENU button, press the IMAGE 
button the number of times corresponding to the remote 
control code for the projector. See “Remote Control Code” 
on page 13.
Setting
Note:
• When different codes are set on the projector and on 
  the remote control, any operation cannot be made. In 
  that case, switch the code on the remote control to fit 
  the code on the projector.
• If the batteries are removed from the remote control for 
  a long period of time, the remote control code will 
  be reset.
This function allows you to change brightness of the screen.
Auto ...........  The brightness according to the input signal 
(between High and Eco mode).
High ...........  Brighter than the Normal mode.
Normal  .......  Normal brightness 
Eco ............  Lower brightness reduces the lamp power 
consumption and extends the lamp life.
Note:
Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized. 
						

							
59

Setting
Key lock
Key lockSecurity (Key lock and PIN code lock)
PIN code lock
This function locks the top control and remote control 
buttons to prevent operation by unauthorized persons. .....  Unlocked.
  .....  Lock the operation of the top control. To 
unlock, use the remote control.
  .....  Lock the operation of the remote control.    
To unlock, use the top control.
If the top control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with your remote control, contact the dealer where 
you purchased the projector or the service center.
This function allows you to use the Key lock and PIN code 
lock function to set the security for the projector operation.
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
 Off  ...........  Unlocked.
 On1  .........  Enter the PIN code every time turning on 
the projector.
  On  .........  Enter the PIN code to operate the projector 
once the power cord is disconnected; as 
long as the AC power cord is connected, 
the projector can be operated without a 
PIN code.
Whenever you change the PIN code lock setting or the 
PIN code (the four-digit number), you are required to 
enter the PIN code. The "1234" is set as the initial PIN 
code at the factory. 
If you want to change the PIN code lock setting, Press 
the SELECT button and the PIN code dialog box 
appears.
Off
PIN code lock
Off
Off 
						

							
60

Setting
Use the Point ▲▼ buttons to select Off, On1 or On. 
Press the SELECT button to close the dialog box. Change the PIN code lock setting
Enter a PIN code
Use the Point ▲▼  buttons to enter a number. Press the 
Point ► button to fix the number and move the red frame 
pointer to the next box. The number changes to . If 
you fixed an incorrect number, use the Point ◄ button to 
move the pointer to the number you want to correct, and 
then enter the correct number.
Repeat this step to complete entering a four-digit 
number.
After entering the four-digit number, move the pointer to 
Set. Press the SELECT button so that you can start to 
operate the projector.
If you entered an incorrect PIN code, PIN code and the 
number () will turn red for a moment. Enter the 
correct PIN code all over again.
Enter a PIN code
The PIN code can be changed to your desired four-
digit number. Press the Point ▼ button to select PIN 
code change and press the SELECT button. The New 
PIN code input dialog box appears. Set a new PIN code.
Change the PIN code
CAUTION:
WHEN yOU HAVE CHANGED THE PIN CODE, WRITE 
DOWN THE NEW PIN CODE IN COLUMN OF THE 
PIN CODE NO . MEMO ON PAGE 83,  AND KEEP IT 
SECUREL y . IF yOU FORGET yOUR PIN CODE, THE 
PROjECTOR CAN NO LONGER BE STARTED .
OffPIN code change