Sanyo Projector Plc Wxu700a User Manual

							
81

This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information 
System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified 
conformance with PJLink Standard Class 1.
For PJ Link password, see page 51 on the owner’s manual of “Network Set-up and Operation.”
Projector Input
RGB
Computer 2 (Analog)
Component
RGB (Scart)
PJLink Input
RGB 2
RGB 1
DIGITAL 1
RGB 3
RGB 4
Video
S-video
VIDEO 2
VIDEO 3
NETWORK 1NETWORK
Computer 1
Video
PJLink is a registered trademark of JBMIA and pending trademark in some countries.
Pj Link Notice
Parameter
12
11
31
13
14
22
23
51
Appendix
HDMI(Digital) 
						

							
8

Vcc
- Data
+ Data
Ground
1

3
4
2
3 4
1
COMPUTER IN 1 /COMPONENT IN /MONITOR OUT (ANALOG)
Terminal: Analog RGB (Mini D-sub 15 pin)
512341096781514131112
Configurations of Terminals
Red (R/Cr) Input/Output   
Ground (Horiz.sync.)
Green (G/Y) Input/Output
-----
Blue (B/Cb) Input/Output
Ground (Red)
Ground (Green)
Ground (Blue)
1
5

4
3
6
7
8
+5V Power/-----
Horiz. sync. Input/Output (Composite H/V sync.)
Ground (Vert.sync.)
DDC Data/-----
Ground/-----
Vert. sync.
DDC Clock/-----
9
13
10
1
11
14
15
RX –
TX +
TX –
RX +

3
4
8 7 6 5 4 3 2 1
5
6
7
8
1
USB CONNECTOR (Series B)
LAN TERMINAL
-----
-----
----------
Appendix
13579111315171918161412108642
TMDS Data 2+  Input
Ground (TMDS Data 1)
Ground (TMDS Data 2)
TMDS Data 1+ Input
TMDS Data 2- Input
TMDS Data1- Input
TMDS Data 0+ Input
Ground (TMDS Data 0)
1
5
2
4
3
6
7
8
Ground (TMDS Clock)
SCL
TMDS Clock- Input
-----
-----
SDA
Ground (DDC/CEC)
11
15
12
14
13
16
17
TMDS Data 0- Input
TMDS Clock+ Input
9
10
Plug insert detection19
18+5VPower
HDMI (19 Pin Type A) 
						

							
83

Appendix
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost 
the number and unable to operate the projector, contact the service station. 
PIN Code Number Memo
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
Put the label below (supplied) on in a prominent place of the 
projector's body while it is locked with a PIN code.
While the projector is locked with the PIN code.
PIN Code Lock No .
Logo PIN Code Lock No .
*Should  the  four-digit  number  be  changed, 
the factory set number will be invalid.
→
Hook and loop fastener 
(supplied)
USB Thumb Drive Case
While the USB thumb drive is not in use, put it in the USB 
Thumb Drive Case to prevent lose USB theumb drive.
Use hook and loop fastener, the USB Thumb Drive Case will 
be a fixed place on the projector.
USB thumb drive case 
(supplied) 
						

							
84
Appendix
Dimensions
Unit:  inch (mm)
Screw Holes for Ceiling MountScrew: M4Depth: 12.0(0.472)
10.14 (257.5) 
13.16(334.2)
2.14(53.8)
3.17(80.5)
3.09(78.4)
5.08(129.0)5.20(132.0)
2.78(70.5)
5.08(129.0)4.43(112.5)
5.51(140.0)
3.66(93.0) 
						

							
KY7AE