Sanyo PLV Z700 Projector User Manual

41
Two different remote control codes are assigned to this projector: 
the factory-set code (Code 1) and the secondary code (Code 2). 
This switching function prevents interference from other remote 
controls when several projectors or video equipment next to each 
other are used at the same time. 
When operating the projector in Code 2, the code for both the 
projector and the remote control must be switched to Code 2.  
To change the code of the projector:
Press the Point 8 or OK buttons to switch...

42
Filter counter
This function is used to set a frequency for the filter cleaning.
When the projector reached a specified time between cleanings, a 
Filter warning icon appears on the screen, notifying the cleaning is 
necessary.
Use the Point 
8 button to select the desired timer [Off/ 50H/ 100H/ 
200H/ 300H/ 400H/ 500H] and press the OK button. After cleaning 
the filter, be sure to select [Reset] and set the timer. The Filter 
warning icon will not turn off until the filter counter is reset.
For...

43
Input Source Information Display
The Information Menu is used for checking the status of the image signal being projected and the operation of the projecto\
r.Video or S-video
A color system of the connected video 
signal is displayed from among PAL, 
SECAM, NTSC, NTSC4.43, PAL-M, and 
PAL-N.
Signal
Component
H-sync freq .
V-sync freq .
Lamp time
Information Menu
A system mode of the connected video 
signal is displayed from among 480i, 480p, 
575i, 575p, 720p, 1080i and 1080p.
HDMI
A system mode of...

44
The WARNING indicator shows the state of the function that protects the projector. Check the state of the WARNING 
indicator and the POWER indicator to take proper maintenance. 
WARNINGblinking red
TOP CONTROL
Warning Indicator
The projector is shut down and the WARNING indicator is blinking red.
When the temperature inside the projector reaches a certain level,  
the projector is automatically shut down to protect its inside. The 
POWER indicator is blinking while the projector is being cooled 
down....

45
Cleaning the RGB panels 
Blemishes such as dust and dirt on the internal optical components of the projector t\
end to degrade the brightness of the 
screen and are likely to appear as a shadow on the screen, which can lead to deterioration of image quality.
This projector has the RGB panel cleaning holes on the underside for cleaning of the internal parts (such as optical 
components) of the projector. When you use the projector for a lengthy period of time or a shadow of dust appears on the...

46
Turn the projector on and press the MENU button to display 
the On-Screen Menu. Select the Setting Menu with the Point 
ed buttons. Press the Point 8 or OK buttons to access the 
submenu items.
1
Put the blower’s nozzle into a hole.
2
Blow air into the projector with the blower watching the 
position of the dust from the screen. 
3
Set the projector back into the right position, then press any 
button on the top control or on the remote control to quit the 
Cleaning function.
4
5
Clean by using the...

47
The air filter prevents dust from accumulating on the surface of the optical elements inside the projector. Should the air filter 
becomes clogged with dust particles, it will reduce cooling fan’s effectiveness and may result in a buildup of internal heat 
and adversely affect the life of the projector. Clean the air filter by following the steps below.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when 
operating the projector . Usage in these environment may 
cause a poor image...

48
Be sure to reset the Filter counter after cleaning or replacing the air filter. 
Resetting the Filter Counter
Filter counterTurn the projector on and press the MENU button to display 
the On-Screen Menu. Select the Setting Menu with the Point 
ed buttons. Press the Point 8 or OK buttons to access the 
submenu items.  
Select Filter counter and then use the Point  8 button to 
select [Reset] and press the OK button. “Filter counter 
reset?” appears. Select [Yes] and then press the OK button.
1
2...

49
When the projection lamp of this projector reaches its end of life, 
the LAMP REPLACE indicator emits yellow light. If this indicator 
lights yellow, replace the lamp with a new one promptly.
The time when the LAMP REPLACE indicator should light is 
depending on the lamp mode.
Follow these steps to replace the lamp.
LampLamp Cover
 
ORDER REPLACEMENT LAMP
  Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information 
to the dealer.
 ●  Model No...

50
Be sure to reset the lamp replacement counter after the lamp is replaced. When the lamp replacement counter is reset, the 
LAMP REPLACE indicator stops lighting.
Turn the projector on and press the MENU button to display 
the On-Screen Menu. Select the Setting Menu with the Point 
ed buttons. Press the Point 8 or OK buttons to access the 
submenu items.  
Select Lamp counter reset and then press the Point 8 or OK 
buttons. “Lamp replacement counter reset?” appears. Select 
[Yes] and then press the OK...