Sanyo PLV Z700 Projector User Manual

21
Menu and its Functions
q
w
e
r
t
y
u
i
q Image
 Select an image mode from among Brilliant cinema, Creative cinema, Natural, Living, Dynamic, and User 
image 1 – 5 (p.27).
w 
Image adj .
 Adjust Brightness, Contrast, Color, Tint, Color temp., White balance (R/G/B), Sharpness, Lamp control, 
Gamma, Progressive, Noise reduction, Advanced menu, Reset, and Store (pp.28 – 33).
e Picture adj .
 Select Overscan, Horizontal, Vertical, Auto adj., Fine sync, and Total dots to adjust the parameters to 
match with...

22
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to focus the image.  
Zoom Lever
Focus Ring
For some frequently used operations, using the remote control is advisabl\
e. Just pressing one of the buttons enables you to 
have the desired operation quickly, and no need for calling up the On-Screen Menu.  
LIGHT button
Press the LIGHT button to light up the remote control buttons. The 
light is automatically turned off when no buttons on the remote 
control are pressed for 10 seconds....

23
Remote Control
IMAGE ADj . button
Press the IMAGE ADJ. button to display the adjustment bar of 
the Image adj. Menu items one at a time and directly adjust the 
selected item. For details, see page 28. 
IMAGE AD j .
button
COLOR TEMP  .
button
✔Note:
	 •	 See	the	previous	page	for	the	description	of	 other	buttons.
	 •	 If	you	press	the	OK	button	after	adjusting	each	 Image	adj.	Menu	item,	it	will	enter	the	main	
menu.
BRIGHTNESS button
Press the BRIGHTNESS button to display the Brightness 
adjustment...

24
Input Source and System Selection
Press the INPUT button on the top control or the INPUT buttons on 
the remote control (see below) to choose an input source.Top Control
INPUT button
Press the VIDEO, S-VIDEO, C1, C2, H1, H2, or PC buttons on the 
remote control according to the input source.
Remote ControlINPUT buttons on the remote control
INPUT buttons
When the video signal is connected to the VIDEO 
jack, press VIDEO.VIDEO
When the video signal is connected to the S-VIDEO 
jack, press S-VIDEO....

25
System Menu (Video/S-Video)
If the projector cannot reproduce a proper video image, select 
a specific broadcast signal format from among PAL, SECAM, 
NTSC, NTSC 4.43, PAL-M, and PAL-N.
Video or S-Video
Component 1 or Component 2
The projector automatically detects the incoming video system 
and adjusts itself to optimize its performance.
When the video system is PAL-M or PAL-N, select the system 
manually.
Use the Point ed buttons to select the Input Menu and 
press the Point 
8 or OK buttons to...

26
HDMI 1 or HDMI 2
When the video signal is connected to the HDMI 1 or HDMI 2 
terminals, select HDMI 1 or HDMI 2 respectively.
The projector automatically detects the incoming video signal and 
adjusts itself to optimize its performance.
If the output signal of video equipment and the input signal of the 
projector do not match, you might not get an image with the best 
quality.
If the blacks of the picture appears unclear (too dark or too light), 
try “HDMI 1 setup” or “HDMI 2 setup” in the Setting...

27
Press the Point ed buttons to select the Image Menu and 
press the Point 
8 or OK buttons to access the submenu 
items.1
2Use the Point ed buttons to select the desired image mode 
and press the Point 
8 or OK buttons. The selected item is 
check marked. Image Menu
Image Mode Selection 
Direct Operation
Menu OperationRemote Control
IMAGE MODE
buttons
For viewing contrasty 3D images in a dark room.  Creative cinema
For displaying user preset image mode in the Image adj. Menu 
(pp.28 – 33). User image 1...

28
Press the Point ed buttons to select the Image adj. Menu 
and press the Point 
8 or OK buttons to access the submenu 
items.1
2Use the Point ed buttons to select the desired item and 
press the Point 
8 or OK buttons to access the selected item. 
The adjustment bar is displayed. 
Image adj . Menu
Press the Point 7 button to decrease the contrast; press the Point 
8 button to increase the contrast (from -31 to +31).
Contrast
Press the Point 7 button to decrease the brightness; press the 
Point 
8...

29
Press the Point 7 button to decrease the sharpness of the image; 
press the Point 
8 button to increase the sharpness of the image 
(from -7 to +7). Sharpness
Lamp control
Use the Point 7 8 buttons to adjust the gamma value to obtain a 
better balance of contrast (from -7 to +7).
Gamma
An interlaced video signal can be displayed in progressive. Use the 
Point 
7 8 buttons to select the desired options.
  Off  . . . . .  Disabled.
  Video  . . .  For moving pictures.
  Auto  . . . .  Auto adjustment...

30
This function can be selected only when Advanced menu in the 
Setting Menu (see page 37) is set to “On.” You can adjust the 
following items through this function. Advanced menu
Iris mode
Adjust the lamp aperture. Select from the following options:
 Mode 1 . . Brightness is prioritized over contrast
  Mode 2 . . Contrast is prioritized over brightness
  Fixed . . . . Fixed lamp aperture set in the Iris range
Iris range
Adjust the upper limit of the lamp aperture (from -63 to 0).
✔Note:
	 •	 Value...