Sanyo PLV Z700 Projector User Manual

11
Remote Control
we
!5
o LAMP CONTROL button
      Select a lamp mode (pp.23, 29).
e LIGHT button
  Light up the remote control  buttons for about 10 seconds 
(p.22).
!5 COLOR button
  Adjust the color intensity of a projected image (pp.23, 28).
q POWER ON/STAND-B y button
   Turn the projector on or off (pp.18, 19). 
!0
r
!4
u
!6
t
o
!2
!7
y
i
u BRIGHTNESS button
  Adjust the brightness of a projected image (pp.23, 28).
!3
r MENU button
  Open or close the On-Screen Menu (p.20).
t POINT ed7 8 buttons...

12
To ensure safe operation, please observe the following precautions:
 ● Use two (2) AA or LR6 type alkaline batteries.
 ●  Always replace batteries in sets.
 ●  Do not use a new battery with a used battery.
 ●  Avoid contact with water or liquid.
 ●  Do not expose the remote control to moisture or heat.
 ●  Do not drop the remote control.
 ●  If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
 ●  Risk of explosion if battery is replaced by an...

13
Projection angle can be adjusted up to 6.5 degrees with the 
adjustable feet.
Rotate the adjustable feet and tilt the projector to the proper 
height; to raise the feet, rotate the both feet clockwise.1
Adjustable Feet
To lower or to retract the adjustable feet, rotate the both feet 
counterclockwise.2
✔Note:
	 •	 The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	ambient	lighting	in	order	to	 obtain	the	best	image.
	 •	 All	measurements	are	approximate	and...

14
The projection lens can be moved up and down or left and right manually with the Lens Shift Rings, enabling you to adjust 
the position of a projected image. After adjusting the position, lock the lens with the Lens Shift Lock.
V
V
uppermost
W
1/2W
Horizontal Lens Shift Ring 
(Left/Right)Move the projection lens to the left or right with the Horizontal 
Lens Shift Ring. 
Move the projection lens up or down with the Vertical Lens Shift 
Ring.
Vertical Lens Shift Ring
(Up/Down)
V
V
W
1/2W
downmost...

15
Video EquipmentS-video 
Cable 
S-VIDEO Output
S-VIDEO
VIDEO
Composite 
Video Output
Video Cable
(RCA x 1) 
Video, S-video
Use a video cable or a S-video cable (commercially available).
Unplug the power cords of both the projector and external 
equipment from the AC outlet before connecting the cables .
Video Equipment
Component Video Output (y, Pb/Cb, Pr/Cr)
COMPONENT
Component
Use a component cable (optional).
Connecting to Video Equipment (Component)
Component 
Cable
(RCA x 3) 
✔Note:
	 •	 To	order...

16
Connecting to a Computer
RGB Scart
Use a Scart-VGA cable (optional).  
Video Equipment
COMPUTER
RGB Scart
21-pin Output
Scart-VGA
Cable
  
Video Equipment
HDMI HDMI
Cable
  
HDMI
Use a HDMI cable (optional) for HDMI output. 
Connecting to Video Equipment (HDMI, RGB Scart)
HDMI Video 
Output
Unplug the power cords of both the projector and external 
equipment from the AC outlet before connecting the cables .
✔Note:
•	 To	order	the	optional	cables,	see	page	58.
COMPUTER
Computer
Monitor Out
Computer...

17
This projector uses nominal input voltages of 100 – 120 V or 200 
– 240 V AC and it automatically selects a correct input voltage. It is 
designed to work with the single-phase power systems having a 
grounded neutral conductor. To reduce the risk of electrical shock, 
do not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult 
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning 
it on....

18
Connect the projector’s AC power cord into an AC outlet and 
turn the Main On/Off switch on. The POWER indicator lights 
red. 
Press the POWER ON/STAND-BY button on the top control or 
on the remote control. 
The POWER indicator turns green and the cooling fans start to 
operate. As the automatic slide shutter opens, a preparation 
display appears on the screen and the countdown starts. 2
3
1
4After the countdown, the input source that was selected the  
last time appears on the screen. 
Turning On...

19
Press the POWER ON/STAND-BY button on the top control 
or on the remote control. “Power off?” appears on the 
screen. Press the POWER ON/STAND-BY button again to 
turn off the projector. 
When the Power off confirmation function is set to “Off,” 
the projector can be turned off without the confirmation 
message. (See “Power off confirmation” on page 40.)
The automatic slide shutter closes and the POWER indicator 
starts to blink red. The blinking continues for about 90 
seconds while the cooling fans...

20
Press the MENU button on the top control or on the remote 
control to display the On-Screen Menu. 
Use the Point 
ed buttons to highlight or select a main menu 
item. Press the Point 
8 or OK buttons to access the submenu 
items. (The selected item is highlighted in ORANGE.)
Press the Point 
7 button to return to the main menu; press 
the MENU button again to exit the On-Screen Menu. Use the Point 
ed buttons to select the desired submenu 
item and press the Point 
8 or OK buttons to access the...