Sanyo Plc Xu305 Projector User Manual

51

Setting
Enter a Logo PIN code
Use	the	Point	▲▼	buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer 	to 	the 	next 	box. 	The 	number 	changes 	to 	
.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	entering	the	four-digit	number,	move	the	pointer	to	
Set ....

5

Setting
Ceiling 
Rear 
Ceiling
When	this 	function 	is 	set 	to 	On ,	 the 	picture 	will 	be 	top/
bottom 	and 	left/right 	reversed. 	This 	function 	is 	used 	to	
project	the	image	from	a	ceiling-mounted	projector.
Rear
When	 this	function	 is	set	 to	On,	the	 picture	 will	be	left/right	
reversed. 	This 	function 	is 	used 	to 	project 	the 	image 	from	
rear	of	the	screen.
Arrow
Pointer
Pointer
You	 can	emphasize	 a	part	 of	the	 projected	 image	with	this	
function. 	Use 	the 	Point 	▲▼...

53

Setting
Power management
Time	left	before	Lamp	is	off.
Power management
For	reducing 	power 	consumption 	as 	well 	as 	maintaining	
the	 lamp	 life,	the	Power	 management	 function	turns	off	the	
projection 	lamp 	when 	the 	projector 	is 	not 	operated 	for 	a	
certain	period.
Select	one	of	the	following	options:
Ready 	.................. 	When	the 	lamp 	has 	been 	fully 	cooled	
down, 	the 	POWER 	indicator 	changes	
to 	green 	blinking. 	In 	this 	condition, 	the	
projection 	lamp 	will 	be...

54

Standby mode
This	function	is	available	when	operating	the	projector	via	
network.
	Normal	...... 	Supply	 the	power	 to	the	 network	 function	 even	
after	 turning	 off	the	 projector.	 You	can	turn	 on/
off 	the 	projector 	via 	network, 	modify 	network	
environment, 	and 	receive 	an 	e-mail 	about	
projector	 status	while	the	projector	 is	powered	
off.
	Eco 	............ 	Select	Eco	when	 you	do	not	 use	 the	projector	
via	 network.	 The	projector’s	 network	function	
will	stop	when	turning...

55

Remote control
This	function	allows	you	to	change	brightness	of	the	
screen.
Normal	...... 	Normal	brightness	
Eco 	............ 	Lower	brightness	reduces	the	lamp	
power	consumption	and	extends	the	
lamp	life.
Lamp control 
Remote control
Lamp life control
The	 eight	 different	 remote	control	codes	(Code	 1–Code	 8)	
are 	assigned 	to 	the 	projector; 	the 	factory-set, 	initial 	code	
(Code	1)	and	the	other	seven	codes	(Code	2	to	Code	8).	
The 	same 	code 	should 	set 	on 	both 	the 	projector...

56

Setting
Key lock
Key lockSecurity (Key lock and PIN code lock)
PIN code lock
This	function 	locks 	the 	top 	control 	and 	remote 	control	
buttons	to	prevent	operation	by	unauthorized	persons.
	.....
	Unlocked.
	 ..... 	Lock	the	operation	of	the	top	control.	 To	
unlock,	use	the	remote	control.
	 ..... 	Lock	the	operation	of	the	remote	control.				
To	unlock,	use	the	top	control.
If	 the	 top	control	 accidentally	 becomes	locked	and	you	do	
not	 have	 the	remote	 control	nearby	 or	there	 is...

57

Setting
Use	the 	Point 	◄►	buttons 	to 	select 	Off,	On1 	or 	On .	
Press	the	SELECT 	button	to	close	the	dialog	box.
Change the PIN code lock setting
Enter a PIN code
Use	
the	Point	▲▼		buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer 	to 	the 	next 	box. 	The 	number 	changes 	to 	
.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the...

58

This	function 	provides 	the 	following 	options 	in 	the 	cooling	
fans’ 	operation	when	the	projector	is	turned	off	(p.22).
	L1	...... 	Normal	operation
	L 	...... 	Slower	 and	lower-sound	 than	the	normal	 operation	
(L1),	but 	it 	takes 	more 	time 	to 	cool 	the 	projector	
down.
Fan
Setting
Choose	the	running	speed	of	cooling	fans	from	the	following	
options	according	to	the	ground	elevation	under	which	you	
use	the	projector.	
	Off 	........... 	Normal	speed.	Set	this	function	to	Off...

59

Setting
Factory default
This	function	returns	all	setting	values	except	for	the	User 
logo,	PIN code lock ,	Logo PIN code lock ,	Lamp counter	
and	
Filter counter 	to	the	factory	default	settings.
Factory default
warning log
This 	function 	records 	anomalous 	operations 	while 	the	
projector	 is	in	 operation	 and	use	it	when	 diagnosing	 faults.	
Up	 to	10	 warning	 logs	are	displayed	 with	the	latest	 warning	
message	 at	the	 top	of	the	 list,	 followed	 by	previous	 warning	
messages	in...

60

Input Source Information Display
The	Information	Menu	is	used	for	checking	the	status	of	the	image	signal	being	projected	and	the	operation	of	the	projector.
H-sync freq .
V-sync freq .
Lamp counter
Information Menu
H
The	horizontal	frequency	of	the	input	signal	is	displayed	in	
KHz	or - - - - - when	no	signal.
The	vertical	frequency	of	the	input	signal	is	displayed	in Hz	
or	- - - - - 	when	no	signal.	Numbers	of	Hz	doubles	when	
during	Interlace.
The	cumulative	lamp	operating	time	is	displayed....