Sanyo Plc Xu305 Projector User Manual

							
51

Setting
Enter a Logo PIN code
Use	the	Point	▲▼	buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer 	to 	the 	next 	box. 	The 	number 	changes 	to 	
.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	entering	the	four-digit	number,	move	the	pointer	to	
Set .	Press	the	SELECT 	button	so	that	you	can	start	to	
operate	the	projector.
If 	you 	entered 	an 	incorrect 	Logo 	PIN 	code, 	
Logo  PIN 
code	and 	the 	number 	(   )	 will 	turn 	red 	for 	a	
moment.	Enter	the	correct	Logo	PIN	code	all	over	again.
Logo	 PIN	code	 can	be	changed	 to	your	 desired	 four-digit	
number. 	Press 	the 	Point 	
▼	button 	to 	select 	Logo  PIN 
code  change 	and 	then 	press 	the 	SELECT 	button. 	The	
New	 Logo	 PIN	code	 input	dialog	 box	appears.	 Set	a	new	
Logo	PIN	code.		
Be	 sure	 to	note	 the	new	 Logo	 PIN	code	 and	keep	 it	on	
hand.	 If	you	 lost	the	number,	 you	could	 no	longer	 change	
the 	Logo 	PIN 	code 	setting. 	For 	details 	on 	PIN 	code	
setting,	refer	to	"PIN	code	lock"	on	pages	56-57.
Use	the	Point	▲▼	buttons	to	switch	On or Off ,	and	then	
press	the	SELECT 	button	to	close	the	dialog	box.
Change the Logo PIN code lock setting
Enter a Logo PIN code
After	a	correct	Logo	PIN	code	
is	entered,	the	following	dialog	
box	appears.
CAUTION:
wHEN yOU HAVE CHANGED THE LOGO PIN 
CODE, wRITE DOwN THE NEw PIN CODE 
IN COLUMN OF THE LOGO PIN CODE NO . 
MEMO ON PAGE 79,  AND KEEP IT SECUREL y . 
SHOULD THE LOGO PIN CODE BE LOST OR 
FORGOTTEN, THE LOGO PIN CODE SETTING 
CAN NO LONGER BE CHANGED .
Change the Logo PIN code lock setting
Change the Logo PIN code
Logo PIN code change 
						

							
5

Setting
Ceiling 
Rear 
Ceiling
When	this 	function 	is 	set 	to 	On ,	 the 	picture 	will 	be 	top/
bottom 	and 	left/right 	reversed. 	This 	function 	is 	used 	to	
project	the	image	from	a	ceiling-mounted	projector.
Rear
When	 this	function	 is	set	 to	On,	the	 picture	 will	be	left/right	
reversed. 	This 	function 	is 	used 	to 	project 	the 	image 	from	
rear	of	the	screen.
Arrow
Pointer
Pointer
You	 can	emphasize	 a	part	 of	the	 projected	 image	with	this	
function. 	Use 	the 	Point 	▲▼ 	buttons 	to 	choose 	
Spotlight 
(Large,	Middle 	or	Small )	,	Arrow ,	Finger 	or	Dot 	and	 press	
the	SELECT 	button.	See	"Pointer	Function"	on	page	12. 
						

							
53

Setting
Power management
Time	left	before	Lamp	is	off.
Power management
For	reducing 	power 	consumption 	as 	well 	as 	maintaining	
the	 lamp	 life,	the	Power	 management	 function	turns	off	the	
projection 	lamp 	when 	the 	projector 	is 	not 	operated 	for 	a	
certain	period.
Select	one	of	the	following	options:
Ready 	.................. 	When	the 	lamp 	has 	been 	fully 	cooled	
down, 	the 	POWER 	indicator 	changes	
to 	green 	blinking. 	In 	this 	condition, 	the	
projection 	lamp 	will 	be 	turned 	on 	if 	the	
input	 signal	 is	reconnected	 or	any	 button	
on 	the 	top 	control 	or 	remote 	control 	is	
pressed.	
Shut down 	.......... 	When 	the 	lamp 	has 	been 	fully 	cooled	
down,	the	power	will	be	turned	off.	
Off 	....................... 	Power	management	function	is	off.	
Timer	................... 	If	the 	input 	signal 	is 	interrupted 	and	
no 	button 	is 	pressed 	for 	more 	than 	30	
s e c o n d s , 	t h e 	t i m e r 	d i s p l a y 	w i t h 	
N o 
signal 	appears. 	It 	starts 	the 	countdown	
until	 the	lamp	 is	turned	 off.	Use	 the	Point	
▲▼	buttons	to	set	the	 Timer(1~30min.).
Note:
		Factory	default	is	 Ready: 5 min .
. 
						

							
54

Standby mode
This	function	is	available	when	operating	the	projector	via	
network.
	Normal	...... 	Supply	 the	power	 to	the	 network	 function	 even	
after	 turning	 off	the	 projector.	 You	can	turn	 on/
off 	the 	projector 	via 	network, 	modify 	network	
environment, 	and 	receive 	an 	e-mail 	about	
projector	 status	while	the	projector	 is	powered	
off.
	Eco 	............ 	Select	Eco	when	 you	do	not	 use	 the	projector	
via	 network.	 The	projector’s	 network	function	
will	stop	when	turning	off	the	projector.
Refer	to	the	owner’s	manual	“Network	Set-up	and	
Operation”.
Note:
•	Factory	default	is	
Eco.
•	When	selecting	
Normal ,	the	cooling	fans	may	be	running	
	depending	on	the	temperature	inside	the	projector	even	if	
	the	projector	is	turned	off.
Setting
On start
When 	this 	function 	is 	set 	to 	On ,	 the 	projector 	will 	be	
automatically 	turned 	on 	just 	by 	connecting 	the 	AC 	power	
cord	to	a	wall	outlet.	
Note:
	 Be	 sure	to	turn	 off	the	 projector	 properly	(see	"Turning	 Off	
the 	Projector" 	on 	page 	22). 	If 	the 	projector 	is 	turned 	off	
in	 the	 incorrect	 sequence,	 the	On	start	 function	 does	not	
work	properly.
Closed caption
Closed	 caption	 is	a	printed	 version	 of	the	 program	 sound	or	
other	 information	 displayed	on	the	 screen.	 If	the	 input	 signal	
contains 	closed 	captions, 	you 	can 	turn 	on 	the 	feature 	and	
switch	 the	channels.	 Press	the	Point	 ▲▼	buttons	 to	select	
CC1 ,	CC ,	CC3	or	CC4.		
If	 the 	closed 	caption 	is 	not 	clear, 	you 	can 	change 	the 	text	
from	
Color 	to	white.
Closed Caption
Note:
The	Closed	Caption	is	available	only	under	the	situation	
below.
    •		When	the	input	signal	is	NTSC	of	composite	and									
							S-video,	and	the	system	is	set	according	to	the	signal		
							or	set	on	
Auto .		
	 	 •	 The	system	must	be	set	on	
NTSC 	or	Auto	in	Video				
		System	Selection.	(P.41)	
	 	 •	 The	icon	of	Closed	caption	is	displayed	in	gray	while	it 	
							is	not	available.	
	 	 •	 The	Closed	caption	is	unavailable	when	On-Screen
						menu	and	P-Timer	are	displayed.
Press	the	Point	▲▼	buttons	to	
select	
CC1 ,	CC ,	CC3	or	CC4,	
and	then	Press	Select	button. 
						

							
55

Remote control
This	function	allows	you	to	change	brightness	of	the	
screen.
Normal	...... 	Normal	brightness	
Eco 	............ 	Lower	brightness	reduces	the	lamp	
power	consumption	and	extends	the	
lamp	life.
Lamp control 
Remote control
Lamp life control
The	 eight	 different	 remote	control	codes	(Code	 1–Code	 8)	
are 	assigned 	to 	the 	projector; 	the 	factory-set, 	initial 	code	
(Code	1)	and	the	other	seven	codes	(Code	2	to	Code	8).	
The 	same 	code 	should 	set 	on 	both 	the 	projector 	and 	the	
remote 	control. 	For 	example, 	operating 	the 	projector 	in	
Code  7 ,	the	 remote	 control	code	also	must	 be	switched	 to	
Code 7.
	To change the code for the projector
	 Select	a	remote	control	code	in	this	Setting	Menu.
	To change the code for the remote control:
	 While 	holding 	down 	the 	MENU 	button, 	press 	the 	IMAGE	
button 	the 	number 	of 	times 	corresponding 	to 	the 	remote	
control	 code	for	the	 projector.	 See	“
Remote Control Code ”	
on	page	13.
Lamp control
Select	the	lamp	operation	when	the	total	lighting	time	of	a	
lamp	exceeds	the	recommended	total	hours	of	use.
Mode 1 	.............. 	A	lamp	can	be	turned	on	even	after
																												exceeding	the	recommended	total	 hours	of	use.
Mode  	.............. 	A	lamp	can	be	turned	on	even	after	
exceeding	the	recommended	total	
hours	of	use.	But	the	projector	turns	off	
automatically	after	3	minutes.
Lamp life control
Setting
Note:
•			 Lamp	mode	cannot	be	changed	for	a	while	after	turning	
on	the	projector.	Lamp	needs	some	time	to	stabilize	after	
the	power	is	turned	on.	Stored	lamp	mode	will	be	active	
after	the	lamp	is	stabilized.
•		If	 Mode  	has	been	selected	and	the	projection	lamp	
			exceedes	the	recommended	total	hours	of	use,	the	
			replacement	icon	will	be	displayed	at	the	time	of	power-
			on.	 Then	the	projector	will	turn	off	after	3	minutes.
	 •		 The	Lamp	replacement	icon	will	not	appear	when	the	
Display	function	is	set	to	Off	(p.48),	during	"Freeze"	(p.27),	
or	"No	show"	(p.28).
Note:
•	When	different	codes	are	set	on	the	projector	and	on	the	remote	control,	any	operation	cannot	be	made.	In	
		that	case,	switch	the	code	on	the	remote	control	to	fit	the	code	on	the	projector.
•	If	the	batteries	are	removed	from	the	remote	control	for	a	long	period	of	time,	the	remote	control	code	will	
		be	reset.
Lamp replacement icon 
						

							
56

Setting
Key lock
Key lockSecurity (Key lock and PIN code lock)
PIN code lock
This	function 	locks 	the 	top 	control 	and 	remote 	control	
buttons	to	prevent	operation	by	unauthorized	persons.
	.....
	Unlocked.
	 ..... 	Lock	the	operation	of	the	top	control.	 To	
unlock,	use	the	remote	control.
	 ..... 	Lock	the	operation	of	the	remote	control.				
To	unlock,	use	the	top	control.
If	 the	 top	control	 accidentally	 becomes	locked	and	you	do	
not	 have	 the	remote	 control	nearby	 or	there	 is	something	
wrong	 with	your	 remote	 control,	 contact	the	dealer	 where	
you	purchased	the	projector	or	the	service	center.
This	 function	 allows	you	to	use	 the	Key	 lock	 and	PIN	code	
lock	function	to	set	the	security	for	the	projector	operation.
This	function	prevents	the	projector	from	being	operated	
by	unauthorized	persons	and	provides	the	following	
setting	options	for	security.
	Off 	...........	Unlocked.
	On1 	......... 	Enter 	the 	PIN 	code 	every 	time 	turning 	on	
the	projector.
	 On 	......... 	Enter	 the	PIN	 code	 to	operate	 the	projector	
once 	the 	power 	cord 	is 	disconnected; 	as	
long 	as 	the 	AC 	power 	cord 	is 	connected,	
the 	projector 	can 	be 	operated 	without 	a	
PIN	code.
Whenever	 you	change	 the	PIN	 code	 lock	setting	 or	the	
PIN 	code 	(the 	four-digit 	number), 	you 	are 	required 	to	
enter	 the	PIN	 code.	 The	"1234"	 is	set	 as	the	 initial	 PIN	
code	at	the	factory.	
If	 you	 want	 to	change	 the	PIN	 code	 lock	setting,	 Press	
t h e 	S E L E C T 	b u t t o n 	a n d 	t h e 	P I N 	c o d e 	d i a l o g 	b o x	
appears.
PIN code lock 
						

							
57

Setting
Use	the 	Point 	◄►	buttons 	to 	select 	Off,	On1 	or 	On .	
Press	the	SELECT 	button	to	close	the	dialog	box.
Change the PIN code lock setting
Enter a PIN code
Use	
the	Point	▲▼		buttons	 to	enter	 a	number.	 Press	the	
Point	
►	 button	 to	fix	 the	 number	 and	move	 the	red	 frame	
pointer 	to 	the 	next 	box. 	The 	number 	changes 	to 	
.	 If	
you	 fixed	 an	incorrect	 number,	use	the	Point	
◄	button	 to	
move	 the	pointer	 to	the	 number	 you	want	 to	correct,	 and	
then	enter	the	correct	number.
Repeat	this	step	to	complete	entering	a	four-digit	
number.
After	 entering	 the	four-digit	 number,	move	the	pointer	 to	
Set.	Press	 the	SELECT 	button	 so	that	 you	can	start	 to	
operate	the	projector.
If	 you	 entered	 an	incorrect	 PIN	code,	
PIN  code 	and	 the	
number	 (
)	will	 turn	 red	for	a	moment.	 Enter	the	
correct	PIN	code	all	over	again.
Enter a PIN code
The 	PIN 	code 	can 	be 	changed 	to 	your 	desired 	four-
digit 	number. 	Press 	the 	Point 	
▼	button 	to 	select 	PIN 
code  change 	and	 press	 the	SELECT 	button.	 The	New	
PIN	code	input	dialog	box	appears.	Set	a	new	PIN	code.
Change the PIN code
CAUTION:
wHEN yOU  HAVE CHANGED  THE PIN  CODE,  wRITE 
DO wN THE  NE w PIN  CODE  IN  COLUMN  OF  THE 
PIN  CODE  NO .  MEMO  ON  PAGE   79, AND KEEP  IT 
SECUREL y .  IF  yOU  FORGET  yOUR  PIN  CODE, THE 
PROjECTOR CAN NO LONGER BE STARTED .
PIN code change  
						

							
58

This	function 	provides 	the 	following 	options 	in 	the 	cooling	
fans’ 	operation	when	the	projector	is	turned	off	(p.22).
	L1	...... 	Normal	operation
	L 	...... 	Slower	 and	lower-sound	 than	the	normal	 operation	
(L1),	but 	it 	takes 	more 	time 	to 	cool 	the 	projector	
down.
Fan
Setting
Choose	the	running	speed	of	cooling	fans	from	the	following	
options	according	to	the	ground	elevation	under	which	you	
use	the	projector.	
	Off 	........... 	Normal	speed.	Set	this	function	to	Off	when	
using	the	projector	in	non-high	altitude	
environment.
	On 1 	........ 	Faster	than	Off	mode.	Select	this	mode	when	
using	the	projector	in	high	altitudes	(about	
1,200	meters	or	more	above	the	sea	level)	
where	the	fans	have	less	cooling	effect.
	 On  	........ 	Faster	than	On	1	mode.	Select	this	mode	
when	using	the	projector	in	higher	altitudes	
than	above	where	the	fans	have	lesser	cooling	
effect.Note: 	
			 Fan	noise	becomes	louder	in	On 1  and	On.
Fan control
This	function	is	used	to	set	a	frequency	for	the	filter	
cleaning.
When 	the 	projector 	reached 	a 	specified 	time 	between	
cleanings, 	a 	Filter 	warning 	icon 	appears 	on 	the 	screen,	
notifying	 the	cleaning	 is	necessary.	 After	cleaning	 the	filter,	
be 	sure 	to 	select 	
RESET 	and 	set 	the 	timer. 	The 	Filter	
warning	icon	will	not	turn	off	until	the	filter	counter	is	reset.
For	 details	 about	resetting	 the	timer,	 refer	to	"Resetting	 the	
Filter	Counter"	on	page	62.
Filter counter 
Filter counter
32H
Press	the	SELECT 	button	to	select		Timer	and	
then	use	the	Point	
▲▼	buttons	to	set	the	timer.	
Select	from	( Off/100H/ 00H/ 300H )	depending	
on	the	use	environment.
Filter	warning	icon	appears	on	the	screen	at	a	set	time. Fig .1 			Filter	warning	icon
Fig .			Filter	warning	icon
Note:
		 This	icon	also	appears	at	turning	on.
Note:
	 •	At	selecting	input	source,	the	icon	(Fig.2)	will	appear.
	 •	The	Filter	warning	icons	(Fig.1	and	Fig.2)	will	not	appear	when	the	Display	function	is	set	to	
Off 	(p.48),	
during	"Freeze"	(p.27),	or	"No	show"	(p.28). 
						

							
59

Setting
Factory default
This	function	returns	all	setting	values	except	for	the	User 
logo,	PIN code lock ,	Logo PIN code lock ,	Lamp counter	
and	
Filter counter 	to	the	factory	default	settings.
Factory default
warning log
This 	function 	records 	anomalous 	operations 	while 	the	
projector	 is	in	 operation	 and	use	it	when	 diagnosing	 faults.	
Up	 to	10	 warning	 logs	are	displayed	 with	the	latest	 warning	
message	 at	the	 top	of	the	 list,	 followed	 by	previous	 warning	
messages	in	chronological	order.	
Note:
	 		When 	the 	Factory 	default 	function 	is 	executed, 	all 	the	
warning	log	records	will	be	deleted. 
						

							
60

Input Source Information Display
The	Information	Menu	is	used	for	checking	the	status	of	the	image	signal	being	projected	and	the	operation	of	the	projector.
H-sync freq .
V-sync freq .
Lamp counter
Information Menu
H
The	horizontal	frequency	of	the	input	signal	is	displayed	in	
KHz	or - - - - - when	no	signal.
The	vertical	frequency	of	the	input	signal	is	displayed	in Hz	
or	- - - - - 	when	no	signal.	Numbers	of	Hz	doubles	when	
during	Interlace.
The	cumulative	lamp	operating	time	is	displayed.
Direct Operation
Press	the	INFO.	button	on	the	remote	control	to	display	the	
Information	Menu.
INFO . button
Remote Control
Press	the	Point	▲▼	buttons	to	select	Information.	The	
Information	Menu	is	displayed.	
See	below	for	displayed	information.
Menu Operation
Power management
Screen
Off	,	Ready	,	Shut down	or	Timer is	displayed.
The	selected	screen	size	is	displayed.
Input
Lamp status
The	selected	input	source	is	displayed.
The	selected	lamp	mode	is	displayed.
Information
Language
The	selected	language	is	displayed.
Key lock
The	selected	Key	lock	icon	is	displayed.
PIN code lock
Off	,	On 1	or	On 	is	displayed.
Remote control
The	selected	remote	code		is	displayed.